Search Documents

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By Mark I. Copeland

This study was conducted by the Bureau of Mines to determine the effect of steel reheating practices in burning natural gas on the amount of silicon required to prevent the formation of copper on steels containing up to 1 wt-pct Cu. Formation of copper, which causes surface hot shortness, was readily prevented by as little as 0.3 wt-pct Si and by 2 vol-pct excess oxygen in the furnace atmosphere when reheating steels containing up to 0.8 wt-pct Cu. Up to 0.8 wt-pct Si content and careful control of reheating conditions were necessary for steels containing 1 wt-pct Cu. Best conditions for these steels were reheating to 2,200° F (1,205° C) in burning gases containing 2 vol-pct excess oxygen, and then to higher temperatures in gases of 6 vol-pct excess oxygen. Slag and mold wash were not detrimental on steels reheated for 8 hr by a soaking-pit-type furnace schedule, but they were problematical on steels heated for 2 hr by a pusher-type furnace schedule. The effect of silicon contents on scaling rates also was determined.

Jan 1, 1974

By Pierre Gaucher

It is possible to selectively mine an orebody by combining the use of the SSW probe with any bulk mining methods as well as narrow vein exploitations. In other words, thanks to the use of the SSW probe, mining operators will be able to reduce and control dilution that is generally associated to every mining operation. Already, quick and substantial savings have been obtained. Falconbridge mines have demonstrated in Sudbury and Raglan operations, that the SSW probe can log nickel, copper and iron sulphides in blast holes. They have raised the grade and reduced dilution by outlining the limits of the ore zones before selectively loading explosives in the blast holes. By lowering the probe in a blast hole, a profile of the ore content is instantly measured and recorded. Logging cored diamond drill holes at the mine have demonstrated that the ore content (nickel, copper, cobalt, PGM) as assayed is proportional to the intensity of the probe?s electromagnetic response (EM), probably because the nickel / pyrrhotite ratio is uniform within a given orebody. The probe also measures the intrinsic conductivity of the sulphides and the percentage of magnetite. All probe readings are displayed and automatically stored at a 10-cm interval within the same reading unit. A 30-meter blast hole takes less than 2 minutes to survey. The whole instrument is light (12 kg) and very simple to use. One operator can carry the SSW system and survey either down or up-holes. The probe works from ?40°C to +50°C. Plotting the measurements of the SSW probe in blast holes (2-3-4-6-10 inches in diameter) before blasting allows to determine the exact shape of the orebody within the waste rock and uneconomic low-grade ore. Thus, only the portion of the holes that contains ore is blasted. The dilution is then much reduced and, by leaving the waste and low-grade ore in place, the mine saves on transportation, blasting, crushing, backfilling, milling, etc. Thousands of dollars are thus saved. Some savings may also be achieved during the development of stopes by guiding development drifts and by replacing diamond drilling by percussion drilling. In some circumstances, when the probe shows that some of the rich ore was not drilled-off, additional blast holes will allow to recover pockets of rich ore that otherwise would have been abandoned in the walls of a stope.

Oct 1, 2001

By A. Tobey Yu, W. Joseph Schlitt, Alfred Weiss, Frederic L. Kadey, Louis Kuchinic

Introduction The February and April 1984 issues of MINING ENGINEERING have already provided introduction to the long-range planning efforts of the Society of Mining Engineers (SME). These efforts are intended to provide the basis for effectively maintaining and improving the Society in the face of the changes that are besetting the mineral industry. This requires that SME recognize what changes are occurring and determine how these will impact the membership. Then a plan must be developed and implemented so that the Society successfully meets the challenges of the next decade. The Board of Directors has charged the Long Range Planning Commission with the responsibility for meeting these goals. This article provides a summary of the work done by the Management and Organization Committee of the Long-Range Planning Commission. This committee's task was to analyze the Society's current organizational structure and management process. Then a set of recommended improvements was to be developed. In doing this, the Committee has been careful to operate under that popular axiom, "If it ain't broke, don't fix it." Thus, changes were not proposed simply for the sake of change, but only where the present system appeared to be less effective than desired. Bases For Action The Committee began by establishing a set of premises about SME and its membership. These premises provided the bases for subsequent actions and recommendations by the Committee. Highlights from the premises included: • The Society should be run on a business-like basis. However, its "business" is that of a not-for-profit scientific, technical, and educational public institution. SME enables professionals involved in or associated with the mineral industry to serve the public purpose of benefitting mankind. • The Society operates as a national (US) organization with transnational (worldwide) interests. It recognizes its obligation to make its goods and services available to minerals professionals throughout the world. In addition, the Society recognizes its obligation to translate technology for the "lay" public, who then also become users of its goods and services. • The Society's Board of Directors is the policy-making body of SME and has final approval of all programs. These responsibilities will become greater when the Society becomes a separate corporation. • At present, the Society provides the following goods and services: publications, meetings/programming/short courses, academic education support, information dissemination - internal and external, and individual member services. • Planning is an ongoing process. It is best performed on a decentralized basis. That is, each major service category should have a responsible group authorized to conduct planning for that category, subject to the Society's master plan and the Board's approval. • The Society is privileged to have highly qualified and motivated members who volunteer their time and efforts on behalf of the Society. The best of these volunteers should rise to the highest positions of leadership - the Presidency of the Society and Institute (AIME). • The Sooiety is strongly committed to the protection and promotion of the history, traditions, and identity of AIME and the use of AIME as the unifying forum for the Constituent Societies. Identification of Potential Problems Once the premises about the Society and its membership were well in hand, the committee began examining the many facets of SME's organizational structure and management process. This was done in order to identify problems or potential problems in these areas. After considerable review and discussion, 10 areas of potential concern were called out for more detailed study and possible recommendations for improvement. These 10 areas include: • A lack of continuity at the Board level and among officers due to the established turnover policy. • A series of subboards that serve, by practice, to diffuse management authority and accountability, rather than enhance it. • A question as to whether the dissemination of information has been adequately planned, organized, and staffed. • An apparent illogical divisional organization. Two divisions are discipline oriented and two are commodity oriented. • A regional organization that does not adequately fulfill its purposes. • Uncertainties about the per-

Jan 6, 1984

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Feb 24, 1997

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

Solid. dense, air-cooled slag can fulfil most, if not all, the functions of natural stone for civil engineering purposes. The value of pumice, also, has long been appreciated, and processes for the manufacture of similar synthetic material for light-weight concretes and insulating fills have been developed in past years.Foamed slag is, in effect, blast furnace pumice and is often referred to on the European continent as metallurgical pumice. It is made by the treatment of molten blast furnace slags with a critical quantity of water during which process the slag cools and expands into a sponge-like mass. The connection between foamed slag and air-cooled slag is also considered and a basis for density control given.All blast furnace slag cannot be foamed to give a product which would comply with B.S.S.877; 1939 Foamed Blast Furnace Slag. A large proportion of the total output of molten slag lacks the necessary inherent properties. This investigation attempts to discover the conditions necessary for the production of foamed slag capable of meeting the British specification.EARLIER WORKIt was generally accepted (Parker, 1951; Gallai-Hatchard, 1955) that the spongy structure of foamed slag was caused mechanically by steam trapped in the slag when it was poured into water. It was assumed that slags which would not foam would not trap steam, because their viscosities and surface tensions were unsatisfactory, on account of temperature and/or composition. The earliest systematic investigation was made by Frisak (1923) who attempted to establish a limiting chemical composition for foamable slags. He decided that foamable slags covered most blast furnace slag compositions on the basis of silica, alumina, and lime, and further "that the replacement of lime by magnesia up to 15 per cent has no noteworthy effect on foamability, that moderate quantities of alkalis are not deleterious, that sulphur raises the foamability and that MnO is only deleterious in the presence of 1...

Jan 1, 1963

By James Westfield

Following is a resume of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction o1 injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bitumi¬nous coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1959

This is the initial issue of STATE MINERAL SUMMARIES. This publication provides estimated data and summaries of mineral activities at the State level for 1988. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1989

A large body of porphyry-type copper mineralization occurs at Panguna in southern BougainviIle. It is associated with the intrusion of quartz diorite/granodiorite into andesites, particularly with the contact zone. Metasomatism of both intrusives and andesite resulted in the formation of biotite pseudomorphing hornblende and the veining of the resultant biotite diorite and biotitized andesite by quartz-chalcopyrite veins with pink orthoclase and dark biotite selvages, respectively.The orientation of intrusives and veins appears to be controlled by premineralization fault-joint patterns in the intruded andesitic Kieta Volcanics.

Jan 1, 1968

By David G. Winter

The first test pile for the carrier pier and south wharf at NAVSTA Puget Sound was driven on December 27, 1989, and the final pile was tested on February 26, 1990. Implementation and modification of the test pile program were done by the owners (WESTDIV and ROICC-Everett), the engineers (ABAM and Hart Crowser), and the contractor and his subcontractor (General Manson Joint Venture and GRL). The site is located as shown on Figure 1. SUMMARY OF THE SOIL CONDITIONS A soil profile along the pier is shown as Figure 2. The soil units can be generalized as follows: ? Upper Silts - Fill, sandy silt, and clayey silt extending from the mudline to an elevation of about -80 feet; ? Intermediate Sand - A medium dense to very dense silty sand unit which is about 30 feet thick near the shore, but thins and disappears offshore; ? Lower Silts - Sandy silts and clayey silts in a medium stiff to stiff condition; ? Deep Sand - A very dense overconsolidated sandy soil encountered at an elevation of about -145 feet.

Jan 1, 1990

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By Kurt O. Hellriegel

Uno de los objetivos de la División médica estriba no solo en cumplir con los requerimientos del Código de minería, sino en el fomento de los principios humanitarios entre los miembros de la comunidad. Por tal motivo, el presente texto refiere la estructura, organización y actividades de la división médica en la Cerro de Pasco Corporation. El primer centro médico más grande y mejor equipado es el Hospital General de Chulee en La Oroya, luego está el Hospital Esperanza y de Huiracocha. Asimismo, la implementación de los equipos adecuados, las funciones del personal técnico y médico, el rol de la administración y el desarrollo del área de las bodegas conforman una estructura idónea y necesaria para el acceso al servicio de salud del trabajador y su familia.

Aug 20, 1963

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004