Search Documents

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer's desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l'Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By R. Schuhmann

Jan 1, 1965

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By Paul Hatmaker

Pumice and pumicite are siliceous volcanic substances quite similar in chemical composition , but somewhat different in physical properties , manner of formation , and mode of occurrence . Production in the United States has increased from 23,271 tons valued at $ 94,943 in 1910 , to 56,843 tons valued at $336,099 in 1930. Both pumice and pumicite are included in these figures as it has been impractical to collect statistical data on the separate commodities .

Mar 1, 1932

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By Gloyd M. Wiles

The property of the Park City Consolidated Mines Co. is situated in the northeast part of the Park City dining district 1 mile east of the town of Park City. The elevation at the collar of No. 1 shaft is 7,250 feet. Park City is a town of approximately 4,500 population lying about 30 miles east of Salt Lake City. The two are connected by an oiled State Highway, which is cleared of snow in winter and maintained in first-class con¬dition by the State throughout the year. The district is served by branches of the Denver & Rio Grande Western and Union Pacific Railroads, each operating on a daily' schedule, except Sunday. These two railroads have constructed 1 ½ miles of joint track from the town to the Park City Consolidated Mines Co. loading tipple, located 200 feet from the portal of the adit that leads to No. 1 shaft.

Jan 1, 1936

By S. Bellec, A. Berton

"Usually, steady state mass balances are used for the design of mineral processing plants. However, this tool does not take into account the impact of process inputs variability nor does it evaluate process transient behaviours between stationary states, such as mill start-up and shutdown. The use of advanced simulations enables the integration of dynamic behaviours in process design decision-making by highlighting situations that are undetectable by using only steady state mass balances. Applying these simulation tools to brown field projects allows the simulator performances to be calibrated and validated on actual plant data before it is used as a prediction tool for the modified plant.Three (3) simulators were implemented at the design stage of a major upgrade project for an ore processing plant in order to assess process behaviours under different production scenarios. These simulators were built to evaluate the impacts on major elements such as mine production, ore stockpile, concentrator production as well as water demand. A validation of individual equipment models was performed whenever sufficient measured data was available. The simulators were then used to study the impact of ore variability (grade, hardness, throughput), to assess day-to-day production special events, and to evaluate the true stockpiles live capacity.The use of a stochastic simulator for equipment sizing allowed a more precise sizing of many pieces of equipment and avoided important expenses in the fresh water pumping system. The dynamic simulator also confirmed that the water in place system would suffice, even in the most demanding production scenario. Finally, the stockpile simulator allowed an important production bottleneck to be quantified and then made possible the assessment of various practical solutions for the stockpiling-reclaiming issues.Post start-up, process data underlines the fact that using advanced simulation tools was useful to mitigate process-related risks associated to the plant expansion, showing generally accurate prediction and adequate equipment sizing, leading to smooth process commissioning. The presented methods are part of what is now routine in Soutex’s participation in both greenfield and brownfield projects."

Jan 1, 2015

By K. Liddell

Current practice for the recovery of platinum group metals (PGM) from flotation concentrates is by energy-intensive smelting processes followed by separation and refining of the base and precious metals. Energy costs are rapidly increasing in South Africa and this trend is forecast to continue in future years. Moreover, the smelting operations are highly susceptible to deleterious constituents, particularly chromite; and the increasing tonnages of UG2 chromititic ore being mined results in an increasing chromite content of smelter feeds. Hence there is a substantial incentive to assess and implement alternative processes to smelting for the treatment of PGM concentrates. The Kell process is a patented hydrometallurgical alternative to smelting that is totally insensitive to the chromite content of the feed concentrate and comprises three commercially proven unit operations (pressure oxidation leaching of base metals and sulfur, roasting and chlorination of precious metals). The Kell process provides the opportunity for existing and new PGM producers to significantly reduce their energy consumption, and in particular their consumption of electricity, by removing the need to smelt PGM concentrates. Energy costs, greenhouse gas emissions and installed power requirements are also much reduced. Compared with smelting and refining these reductions are calculated as: ? Total energy consumption-50% reduction ? Electrical energy consumption-84% reduction ? Energy consumption costs-76% reduction ? C02 emissions-70% reduction ? Installed power requirement 92% reduction. The data obtained from simple laboratory batch amenability testing can be readily applied to the Simulus mass and energy balance simulation procedure to determine energy and reagent consumptions, equipment selection and process optimization. The applicability of Kell to treating low-grade 'dirty' concentrates with high UG2 content as well as to polymetallic concentrates containing base metals as the major payable metals with subordinate PGM means that these savings can also be expected when the process is used for treating a range of concentrate types and grades. Keywords PGM,UG2, Merensky, smelting, chromite, electricity, hydrometallurgy, Kell Process, Eskom.

Jan 1, 2011

By Lyman G. J

Magnetic separator operation in the recovery of magnetite in heavy medium circuits was studied by conducting a series of tests on a full size wet drum magnetic separator.The significant operational variables were found to be feed pan clearance, squeeze pan clearance, dry magnetite feed rate and separator drum speed. With feed and squeeze pan clearances optimized for typical primary separator operation, magnetite loss and concentrate specific gravity were found to be related in a regular manner to dry magnetite feed rate at any drum speed.A two component model of magnetite loss is proposed, relating total magnetite loss to losses in the feed pan and squeeze pan zones. The experimental curves relating magnetite loss to dry magnetite feed rate at the various drum speeds are interpreted in terms of the two component model.The magnetite particle size distribution in the separator was also examined. The tailings magnetite was found to be finer than the feed magnetite only when the dry magnetite feed rate was low, or immediately following the introduction of a new charge of magnetite when the separator was fed at an intermediate dry magnetite feed rate.

Jan 1, 1983

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting Cu, Ni, Co, and S from high grade Ni concentrate produced from Lynn Lake ores and describes in some detail the chemistry of the process. In the leaching stage air, ammonia, and sulphide minerals react in a sequence of inter-related steps to produce soluble amines of Ni, Cu, and Co in a solution containing sulphate, thiosulphate, polythionate, and sulphamate ions and a controlled amount of free ammonia, the iron and other components of the concentrate remaining as an insoluble residue which is separated from the leach solution by filtration. The pregnant solution produced in leaching is further treated by boiling to precipitate and remove Cu as cuprous sulphide, leaving a copper-free solution with a composition suitable for subsequent precipitation of Ni and Cu by H,

Jan 3, 1955

By K. Yathavan

Fracturing of rock at low stress levels can be a source of unexpected problems in rock engineering: • the resulting instability can be a safety hazard; • in very brittle rocks it may be associated with violent failure of the rock and strainbursting (rockbursting); • it usually leads to an unexpected requirement for rock support, with time and cost implications; • in rock boring projects, it may result in fracture of the rock ahead of the bored face and in the walls of the bore behind the face. This may lead to cutter head vibration, increased cutter wear and consequently decreased performance and increased costs. Examples of situations in which fracturing of rock at very low stress levels has been observed will be described. This will include details or estimates of the in situ stress magnitudes and the rock strengths involved. La brisure de roche sous faibles contraintes peut être l’origine de problèmes inattendus en génie minier : • L’instabilité résultante peut devenir un danger • Elle peut provoquer des éclatements violents des roches fragiles • Elle nécessite souvent une infrastructure de soutien de la roche, ayant des implications sur les coûts et les délais • Les forages de la roche peuvent provoquer une brisure de celle-ci au niveau de la surface forée mais ainsi à l’intérieur de la roche, causant parfois des vibrations et une fatigue de la tête de forage, induisant une baisse de performance et un accroissement des coûts. Nous avons décrit ci-après des exemples de situations de brisure de roche sous faibles contraintes. Cette description comprend des détails ou des estimations des forces et des contraintes impliquées. Cette étude représente la base du travail de recherche effectué sur le phénomène. ißbildung im Gestein unter niedrigen Stressbedingung kann eine mögliche Ursache sein für unerwartet auftretende Probleme in der Felsmechaniklehre: • Die resultierende Instabilität stellt ein mögliches Sicherheitsrisiko dar; • In sehr sprödem Gestein kann es verbunden sein mit einem plötzlichen und gewaltsamen Zerfall des Gesteins; • In den meisten Fällen ist eine nicht eingeplante Gesteinsabstützung erforderlich, und damit ein Zeit- und Kostenaufwand verbunden; • Bei Bohrungsprojekten kann es dazu führen, daß es während des Bohrvorganges zu einer Rißbildung im Gestein hinter und vor der gebohrten Felswand kommt. Dies kann Bohrkopfvibrationen, eine erhöhte Bohrkopfabnutzung und folglich eine Bohrleistungssenkung, sowie Kostenerhöhung zur Folge haben. Das Phenomen von Gesteinsrißbildung unter niedrigen Stressbedingung wird anhand von einigen dokumentierten Beispielen erörtert. Diese beinhalten zudem Details oder Schätzungen bezüglich der Stärke des in situ Stressfeldes, sowie der gegebenen Gesteinsstärken. Die mit diesem Beitrag dokumentierten Ergebnisse formen eine Grundlage zur weiteren Forschung dieses Phenomens.

Jan 1, 2003

By Cláudio Magno do Carmo, Gilmar Pinto Ribeiro, Luciney Miranda Martins

A rotina operacional e os seus processos de validação e acompanhamento já estão consolidados no ambiente da Tecnologia da Informação (TI). No ambiente da Tecnologia de Automação (TA) estamos avançando lentamente, apesar da grande semelhança em vários processos, devido a dificuldades de adaptação dos controles principalmente no tocante aos tempos de resposta e atuação das equipes. Enquanto a TI atua na garantia da execução do tripé formado por confidencialidade (segurança), integridade (precisão dos dados) e disponibilidade, rigorosamente nessa sequência de prioridades (CID) [1], a TA procura atender às necessidades da produção, e inverte a prioridade para a disponibilidade (DIC). Daí o conflito inicial entre os modelos: demanda imediata ou planejamento detalhado das atividades dentro dos padrões de qualidade da TI, entretanto sem impactar nas metas operacionais. É tudo uma questão de visão e principalmente de gestão por processos! Quais as diretrizes comuns? Quais os processos similares? Encontrar os pontos de afinidade, alinhados com as expectativas dos gestores e com foco na disponibilidade, sem perder a integridade e confiabilidade dos dados é o desafio.

Oct 1, 2019

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By Peter M. Watt

The objective s of this paper are: (a ) to examine and discuss the burdens we place on our extractive industry; (b) to compare the levels of taxation in Canada with those in other countries; and ( c) to suggest certain broad parameters within which our taxation policies may be made more rational and stable. Among the burdens identified are taxation, the ownership and use of our resources, environmental issues and the rather emotional issue of so-called 'super profits'. Finally, the paper will address certain broad but key areas of policy which need attention and agreement if our tax system is to be made more rational. Such areas include: whether and if so why the extractive industry should be given incentives;. what circumstances, if any, justify a 'higher' than normal' level of taxation, and, ?if the concept of economic rents is a justifiable one, how might a basis for them be established which recognizes the fluctuating value of much of the industry's output. Note: The paper was written before the 1977 Federal and Provincial budgets were presented. Consequently, the paper does not reflect any changes proposed in these budgets.

Jan 1, 1977

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By W. A. Padgham, H. Helmstaedt

Field evidence for current hypothe e about age and kinematic ignificance of gold-bearing hear zones in the Archean Yellowkni fe greenstone belt is reviewed , and it is concluded that major disagreements between previous workers are a direct result of differences in stratigraphic and tructural in terpretations of the Yellowknife Supergroup. Although goldbearing hear zone appear to be confined to the mafic volcanic pile of the Kam Group. it can be shown that shearing affected all supracru tal rocks, including the Jackson Lake Formation. now con idered to represent the youngest unit of the Yellowknife Supergroup. tructural ob ervations are incompatible with the hypothe is that the hear zones represent loci of ynvolcanic gravity sliding but are consistent with earlier conclu ions that shear zone development commenced with rotation of the volcanic pile and continued as re ult of lateral shortening broadly overlapping with the emplacement of granitoid batholiths. Shear Zones are common throughout the entire green tone belt. yet productive zone are confined to the Yellowknife Bay Formation of the Kam Group and localized where flow abut with a high angle again t the contact of the We tern Plutonic complex. However. no obvious tructural and lithological features have been recognized that are more favorable for gold deposition and distinguish the shear zones and flows of the area around the mines from those of other parts of the greenstone belt. The model that gold wa transported by metamorphic solutions and that hear zones were the firs t-order control for gold deposition provides no explanation for the trong localization of the depo it . As porphyries with elevated gold contents are present in and near ome of the mines. the possibility that gold was deposited from hydrothermal system around fel ic intrusion representing early phases of the Western Plutonic complex should be given erious consideration.

Jan 1, 1986