Search Documents

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

The first part (lH of this work dealt with the process of recrystallization of single crystals of lead after deformation by creep, as revealed by macroscopical examination. It was shown that when recrystallization commenced, a crystal, termed the primary crystal, started to grow at the edge of the specimen and extended into the body of the specimen along the slip planes. At some stage during the growth of this crystal, other crystals appeared at the boundary of this first crystal and fragments of the parent crystal. From thispoint, recrystallization was accelerated with relatively rapid necking down of the specimen until fracture occurred.All those crystals formed after the primary crystal were given the term secondary crystals. In the present paper is given a detailed account of the orientations of the primary and secondary crystals.EXPERIMENTAL METHODThe size of the test pieces and the manner of loading were given in the previous paper (1). X-ray back reflection photographs were taken of the individual primary and secondary crystals and from them were determined the orientations. The path of the X-ray beam was perpendicular to the surface of the creep specimen.In view of the large number of photographs needed, gold...

Jan 1, 1940

By Jozef F. Zurawski

River Des Peres Foul water Interceptor (Skinker–McCausland Tunnel) is a gravity sewer tunnel constructed to eliminate dry sewage overflows during high river stages and to improve the wastewater collection and treatment. The original 78-inch (2m)finished diameter Skinker-McCausland Tunnel started as a 21,500 feet (6.5km)interceptor with 13 work, drop and access shafts. The tunnel constructions included soft ground, mixed face and rock tunneling in karst formation with maximum overburden of 175 feet (53m). Due to the success of the project, the tunnel alignment was extended another13,361 feet (4.1 km) and 7 new structures by negotiating two additional segments with the contractor and the designers.

Jan 1, 2001

We report the studies of Proton-Exchange Membrane Fuel Cells (PEM FC) and hydrogen storage materials at McMaster University for the last 14 years. From the initial investigation of ionic conduction mechanism to the revelation of the origin of non-Arrhenius temperature dependence, as well as the synthesis and characterization of high temperature polymer electrolytes, both experimental and theoretical works have been compiled for the fuel cell membranes. In addition to the discovery of suppressed ionic conduction in Electrode-Membrane Assembly (EMA) and novel hydrocarbon PEMs based on micro-emulsion, the first evidence of hydrogen adsorption saturation by carbon nano-tubes was also achieved, which has been the bottleneck for the application of PEM FC. Prior to our study, a number of controversial publications have claimed the hydrogen capacity of these materials to be between 0.1 to 10.0 wt.%, and none demonstrated a plateau of adsorption with pressure that is consistent with monolayer saturation. Others suggested that the tube bundle structure is opened under high pressure to enable higher adsorption on newly uncovered surfaces, but received no confirmation. Using our home made high-pressure instrument with in-situ electrical probes, we found that a plateau is nearly achieved at about 300 atm in the room temperature isotherm, and that nanotube bundles actually compress with pressure instead of splitting, using in-situ electrical measurements.

Jan 1, 2005

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By M. J. Ankeny, J. J. Forbes

The United States Bureau of Mines often receives inquiries from the mineral , petroleum , and allied industries concerning the essential steps to be taken in the formation of Holmes Safety chapters and councils . The purpose of this circular is to answer in a general way such inquiries and to relate briefly the history and work of the Holmes Safety Association to the present date .

Jul 1, 1931

By R. L. Marek

The number of persons fatally injured in the California petroleum industry, in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry--reduced personnel, decreased active field development, and curtailed production--have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period.

Jan 1, 1933

Jan 1, 1968

Lime and Marble Limited was founded by the late T J McKee OBE and his family in 1935. The Company had its base in the high grade marble deposits on Takaka Hill, and was also shipping crushed limestone to the Auckland glass works, and supplying burnt lime for industry.

Jan 1, 1998

By Michael Casson

With the mining industry changing rapidly due to mergers, acquisitions and fluctuating market pricing, today?s market for coal, minerals, ores and aggregates demands electrical apparatus that perform every time with maximum efficiency and with consideration for personnel safety. This is especially true in existing mining operations where every payload counts. Draglines are the workhorses of surface mining operations, and reliable and efficient operation is absolutely critical to success. However, the inherent disadvantages of using dc motors and motor-generator (MG) sets can significantly impact productivity and return on investment (ROI).

Jan 1, 2013

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By K Kermanshahi, J Allen, MáHilden, M Powell, S Mwansa, S Palaniandy

Approximately 420 VertiMills« (VTM) have been installed in mineral processing plants throughout the world, mainly in tertiary and regrind applications plus several in secondary grinding duties. Metso Minerals (Metso) and the Julius Kruttschnitt Mineral Research Centre (JKMRC) have commenced a collaborative research program in stirred milling technology focusing on mill performance evaluation, model development and scale-up methodology. Industrial VTMs are being assessed using a consistent circuit survey protocol to evaluate the performance of VTMs in comminution circuits. The survey protocol includes identification and modification of sampling points, appropriate sampling techniques, controlled circuit stability, and best sample analysis practice. To initiate this study four surveys were conducted in the tertiary grind circuit in the Ridgeway Concentrator at Cadia Valley Operations (CVO) that treats the full circuit throughput of over 800 tph. To deal with the high feed rate the site opted to lead the world in the application of stirred mills by installing the largest VTM, at 3000 hp (2240kW) in closed circuit with a hydrocyclone bank. On average the operating work index was 13.1 kWh/t, reducing the secondary grind product by 40 - 50 ¦m to the required 80 to 100 ¦m range. The applied specific energy is relatively low in these low-intensity stirred media mills at 2.7 kWh/t. The size specific energy was 24.2 kWh/t-75¦m. Based on the survey and operating data the VTM circuit is performing well in this high-throughput tertiary grinding application, producing a sub-100¦m product.CITATION:Palaniandy, S, Powell, M, Hilden, M, Kermanshahi, K, Allen, J and Mwansa, S, 2013. VertiMill« - Development of circuit survey and performance evaluation protocols, in Proceedings MetPlant 2013 , pp 162-175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Alvinus Brown Wood

THE ancient copper-mines of Lake Superior, having been destroyed or covered by-modern mining-dumps, are not accessible to the present inhabitants of that region, and, since no more are likely to be found, some account of those already discovered, from one who has seen them, may be acceptable to the Institute. Early in May, 1855, 1 took a party of men to open an ancient pit on the Quincy mine-location. Mr. C. C. Douglas was the Agent.," as mine-managers were then called on Lake Superior. The Quincy Co. had previously done work on a fissure-vein, several hundred feet west of the Amygdaloid lode (afterwards called the Pewabic lode), on which was the ancient pit herein described. It was at this pit that the Quincy' main shaft was subsequently stink. The ancient pit showed an apparent depth of about 4 ft., but when cleaned out it was shown to be 14 ft. deep, having been filled up by the sliding-in of material composed largely of broken rock, taken out in sinking the ancient shaft, and left near its mouth. Midway of the shaft, and below water-level, was found a scaffolding, of white-birch poles,- which had been used as a landing, to assist in removing the excavated rock. The shaft was 7 ft. in diameter. The excavation had been done by first building fires in order to disintegrate the rock, as was proved by the abundance of charcoal found; then breaking the softened rock with hammers of diorite, such as is found in the greenstone range on Keweenaw point. These hammers had about. the size of large paving-stones. Only broken ones were found, the whole ones having been doubtless carried away for other work, such as could be traced on the lode for a hundred feet or more to the south. At the place where this shaft was stink, barrel-copper (i.e.,

Mar 1, 1906

By J. A. Hudson, D. L. Millar

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Rock engineering system performance monitoring using neural networks.) Synthetic and analytical approaches to objective-based design of rock engineering projects are discussed. Rock masses are considered as complex dynamic systems with components that concurrently interact with each other and their environment. The existence of a rock engineering system canon (i.e. a set of systems governing rules) is proposed. Its possible components are highlighted and an application is demonstrated using a "rock mass automaton" designed to simulate dynamic heat distribution in rock. In the example given, the canon implements the basic result from probability theory applied to the thermodynamics of solids. Rock engineering system performance is reduced to the mapping of the output of a rockmass to varying input (design) options, within the state space of the systems model. The Kohonen Self-Organising Map provides an extremely useful analytical tool to reduce the hyper-dimensionality of rock engineering system behaviour. Further, the hyper-dimensional state vector is mapped "quasiconformally" such that the neural map tends to spatially organise similar input state vectors, facilitating interpretation of rock engineering system behaviour (performance monitoring). Work is reported on the development and validation of the automation as a basis for an internal representation of the rock mass bahaviour. The results are reported of simulations compensating for the uncertainty of the exact mechanisms operating within the rock mass, using additive noise with the input state vector in the training stages of the self-organising map implementation. Initial work on adopting Grossberg's Adaptive Resonance Theory neural network architecture for classification of rock engineering systems behaviour is also presented

Apr 1, 1994

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

[Thin roport. C"WAW; I Ac rvq"I LN 01 a tvchniv&ll nnd oco I in j ;- I iv It i on c)l roncc p Ln,I I Lc!iin I OV Lhe undprnro"nd vNing, ruh h! i zn(kn, And 1" viiii rutoriin- of Opp &L :;halo drponi1q. Study L-I 10 1 1:; ..vi c I i rst d it cc tvd L ""Ards "vA I "it Wit "I the ippLWAhle q(t)¬logy, .in:;"(OLud ;hintvirak, r"ck muchnnics, ii; Olu rolturving, acum; mining, votitiInthn, iiiHtl I' it inn, vaFrry, :ind nn': iru"muniAl iNpiet InvI ors ConroptuAl mv:Lvmn wore nv"tWqjW rind Wen ovALUOILed agalnSt I lIt"n I it' 1 ttCS I runt ho I I I ;I I cc!ii i (.:I I A I I( I ocon "mi t?. vivwpn Lnt . Thu I CS" ICS 01 Lhunv vv&"Mions wpru thun ;lira ly-Ptl ind, KNqwd upon this analls is , hit foll"wkg two syntvmn writ' 5VIecLind lor furLhpu study in Phaso Ll: 4 -Ili I I : kcoiii nid Pi I lair -Art ica L DrL I I and Blasr SyKyw 1V: THOW Hori"g-Horiz"nuaL Ring Drill anti BI-ast Thiq rvpnrL is nahmillrd in fulAllarrit or We Phzni, J parLion ul (Arnt KICL Oinhou SON LO/ 1 by Nni x & Kc Won , I nc. Co thp D. nvor Rostnrch Cvntpr, Uni-LPd AL"tpn DWPAUxiont of the InLerilor, QUrCJlH of Mines. Ark wns tonpirrind as of March, 1979.]

Jan 1, 1975

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilisation to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilised to produce more effective dispersant systems which allow the preparation of, added value, higher solids and finer particle size calcium carbonate slurry products.INTRODUCTIONConcentrated aqueous dispersions of fine, particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently more than 10 million tonnes of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e. its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximise the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimise drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003