Search Documents

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By I Halikia, T Lilis

Lead smelter slags, produced during the last century in quantities ofmillions of tonnes at Lavrion, Greece, have recently been used in theconstruction of Lavrion harbour. In order to evaluate the geochemicalstability of slags and assess their environmental impact on the aquatic environment, a detailed study on lead leachability under conditions that simulate subsea environments was carried out. Leaching experiments using magnesium chloride solutions under mild temperature conditions were conducted and the effect of main parameters on lead solubility was examined. Furthermore, kinetic analysis on the experimental results was performed. Based on the results, lead dissolution increases by increasing the reaction time, magnesium chloride concentration in the bulk solution and temperature, whereas it decreases by increasing the slags particle size. The reaction order was found to be approximately 0.5 at the initial extraction stages and the activation energy value from the Arrhenius plot was estimated to 29.8 KJ/mole. Diagnostic equations applied to all the experimental data reveal that lead dissolution is mainly controlled by diffusion through the ferrosilicate matrix of the slag particles, which is in accordance with the low activation energy value. The JanderÆs diffusion equation [1-(1-a)1/3]2=kt was proposed as the equation representing the reaction of lead dissolution from slags using magnesium chloride solutions.

Jan 1, 1999

By Frank G. Breyer

THE .following developments in the zinc field during 1935 are listed in the order of their importance. Each will he amplified in later paragraphs. In the field o f Metallic Zinc: (1) Construction of further continuous vertical retort smelting capacity in the United States and Germany. (2) Expansion of fractional distillation capacity in the United States. (3) Great expansion in the zinc-base die-casting industry in the United States and abroad. (4) Wide acceptance of heavy galvanizing by the steel industry. (5) Construction of the first commercial wire electroplating plant for putting on heavy coats of pure zinc. (6) Firm establishment and appreciable expansion of the practice of using zinc dust as a reducing agent in the organic chemical industry.

Jan 1, 1936

By Ed Beswick

Resource Update Drilling Program ? Pre-feasibility ? Exploration Metallurgy Program ? Grindability ? Metallurgical Optimization ? Hydrometallurgical Options Preliminary Mine Development Design Environmental Permitting Infrastructure Development

May 1, 2008

By Victor Velho de Castro

O presente trabalho tem por objetivo avaliar a resistência ao desgaste de dois diferentes materiais (três amostras de aço SAE 52100 e três amostras de SAE 1045) em diferentes condições microestruturais, sem lubrificação e com lubrificação (utilizando biodiesel B100, óleo diesel/biodiesel B50 e óleo diesel comercial B7). Quatro amostras foram submetidas a tratamento térmico de têmpera (830°C resfriado em óleo nas amostras de aço SAE 52100 e 850°C resfriado em água nas amostras de SAE 1045) seguida de revenimento (100°C e 200°C nas amostras de aço SAE 52100 e 100°C e 300°C nas amostras de SAE 1045). Os ensaios foram realizados em um tribômetro do tipo pinosobre- disco, com rotação de 300 RPM, 1,5kg de carga e 4400m de distância percorrida, seguindo as recomendações da norma ASTM G99–95, medição da microdureza superficial da pista de desgaste e avaliação da superfície desgastada das amostras com um Microscópio Eletrônico de Varredura (MEV). Ao final dos ensaios, observou-se a variação da resistência ao desgaste entre os diferentes materiais, diferentes microestruturas e diferentes lubrificantes aplicados no ensaio. Os resultados indicaram uma tendência de diminuição de desgaste nos ensaios realizados com lubrificação de biodiesel B100.

Aug 16, 2017

By Heidy de Oliveira Simões

Visando entender os impactos causados pela formação de trincas e deformação das pelotas na qualidade física do material, foi desenvolvido um algoritmo que, através de análise automática de imagens, é capaz de medir o tamanho da trinca, sua largura e comprimento, bem como efetuar as medições de tamanho e morfologia da pelota queimada. Foram analisadas pelotas produzidas com minério hidratado (elevado teor de goethita) com 2 perfis térmicos distintos. Os dados obtidos na análise de imagem foram correlacionados com a resistência à compressão das pelotas e evidenciaram o tamanho das trincas denota notória correlação com a sua resistência física. A medição das trincas formadas pela deformação da pelota no leito (denominadas resiliência) permite evidenciar o quanto a pressão no leito de pelotas impacta na qualidade após a queima, bem como indica o ponto ótimo para que não acarretem em perda da resistência. A medição do tamanho das trincas térmicas mostra-se essencial, pois mesmo em perfis mais suaves de queima pode haver a formação de tais trincas, sendo que o tamanho e a abertura da trinca é que definem a melhor ou pior resistência. O conhecimento, e possível aplicação prática, da avaliação das trincas poderá auxiliar na otimização de perfis térmicos de fornos de pelotização.

Aug 16, 2017

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By Clinton C. Knox

Attention of mine operators and engineers in the Picher zinc-lead field has been drawn increasingly in recent years to marginal ore deposits lying at greater than normal depth below surface in the marked structural depressions known as the Miami and Bendelari troughs. Not only mining but prospect and development drilling is relatively costly in the bottoms of the structural depressions known as the. Miami and Bendelari troughs which cross the center of the Picher field. Nevertheless, operations by various mining companies in recent years have shown that no insuperable problems exist, and with the gradual lowering of grade cut-offs throughout the field, certain potential deep-ore areas, previously only partly explored seemed worthy of further investigation. Some such areas were called to the attention of Bureau of Mines engineers by lease holders and operators, while others were noted in the course of Bureau's systematic investigation of Tri-State ore reserves. The writer was assigned to make a study of. those possible "trough extensions," in the course of which all available nine maps, drill logs, and prior reports were assembled. Subsequently 41 churn drill holes were bored by the Bureau in the periods October 1944 to May 1945 and October 1946 to April 1947. The general area under investigation this project is indicated on figure 1, which likewise shows its relation to nearby towns, roads, and railroads. The location of individual deposits included in the report is indicated more clearly on figure 3. Minable ore was found in only two holes, and the structural information procured by drilling was less encouraging than anticipated. This report, however, presents all factual data obtained, in the belief that they may be useful in subsequent prospecting and development projects in the areas investigated. There are also set forth some of the stratigraphic data relative to the Picher field ns a whole and the Miami and Bendelari troughs which were assembled in the preliminary investigation of this project.

Jan 1, 1949

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By S. J. Frank

Ferroalloy furnaces are well known to be extremely difficult to control from a metallurgical perspective. Mostly metallurgical control is still reactive in nature, causing a significant amount of reworking and product blending to achieve a proper product specification. Despite numerous efforts towards the model based control of primary smelting operations, actual metallurgical feed forward control seems to remain elusive. One of the key reasons in the failure to model these metallurgical reactors well, is that fundamentally orientated pyrometallurgists, statisticians, data miners and control engineers very often have diverging ideas how to model these systems. Furthermore, metallurgists have often come to rely on their ability to develop empirical regression models of furnace behaviour, as they have lost their faith in the ability of thermochemical and metallurgical engineering fundamentals to accurately predict the outcomes from furnaces. This paper shows how good thermochemical modelling can be combined with proper technological and systems analysis, as well as a proper inventory model, to predict the alloy and slag chemistry with good accuracy one tap into the future, at a time horizon of typically around 4 to 6 hours. For this modelling approach, a number of tools will be used, such as data reconciliation, thermodynamic modelling using Fact Sage®, inventory and heel estimation, neural networks and statistical data exploration. Furthermore, systems identification theory will be combined with the approaches given above to develop a truly dynamic predictive model. This paper seeks to demonstrate the need for a hybrid approach, which incorporates plant data and readily accessible thermodynamic data to develop a proper dynamic model.

Jan 1, 2004

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By Eduardo Côrtes de Castro

O presente trabalho aplica o modelo de análise de capacitação tecnológica desenvolvido por Figueiredo (2001) para definir um método de aumento de competências e melhoria de performance numa unidade de prestação de serviços da Companhia Siderúrgica Nacional, a gerência de oficina de cilindros de laminação. A utilização deste método permitiu o aumento da capacitação técnica da unidade, através dos processos de aprendizagem subjacentes, e a melhoria de performance, medida por indicadores chave de desempenho relevantes para o resultado da empresa (qualidade, custo, atendimento e produtividade da mão de obra). São apresentados, além dos resultados, a estrutura analítica do modelo proposto e as evidências associadas às capacidades tecnológicas acumuladas e aos processos de aprendizagem.

Oct 30, 2017

By Juan Carlos Salas

In this paper, a collaborative R&D model which has been successfully applied by a global mining companies association is presented and analysed both from the conceptual and practical point of view and an example of these collaborative initiatives, the Copper Technology Roadmap recently generated by a group of the most relevant copper mining companies, is presented, including an analysis of strategic opportunities and challenges in the Latin American region.

Sep 9, 2007

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By NONE N

Jan 1, 1963

By Laura Pires Ribeiro Martins

Para a produção de peças e componentes automobilísticos, a utilização de ensaios não destrutivos é de grande importância, tanto para a detecção de defeitos como para a estimativa de propriedades físicas e mecânicas. Este estudo tem como objetivo avaliar dois métodos de ensaios não destrutivos (frequência de ressonância e ultrassom) através da determinação do módulo de elasticidade e do amortecimento de vibrações, em ferros fundidos vermiculares de classe FV 450. Estas técnicas também foram avaliadas para identificar a presença de microporosidades de contração na solidificação. Verificou-se que estas metodologias permitem estimar valores de módulo de elasticidade com bastante precisão, superior à obtida com ensaios de tração. Comprovou-se ainda que a capacidade de amortecimento de vibrações, avaliada pela taxa de atenuação da oscilação, é sensível à presença de interfaces na microestrutura do material, bem como à presença de pequenas porosidades.

Aug 16, 2017