Search Documents

By R Peden

Recent, detailed mapping, (Allibone, 1986; Peden, in prep.) of north west Stewart Island, has shown that the Rakeahua Granite (Watters et al, 1968), is comprised of a wide range of granitoid bodies ranging from diorite to leucogranite. As a result of the wide variation in granitoids Allibone (1986), suggests renaming of the Rakeahua Granite to the Rakeahua Granitoid Complex. Names were also proposed for the individual granitoid bodies mapped.

Jan 1, 1987

By R WOODS

The interaction of, flotation collectors with sulphide mmerals takes place at the solid-solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulphides is an electrochemical process, xanthates being electro-oxidized to chemisorbed xanthate and dixanthogen.The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidized xanthate species. The action of reagents which can activate or depress the flotation of sulphides is discussed briefly.

Jan 1, 1972

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By H. Sahay

The current Canadian coal production is approximately 57x106 tonnes per annum of which some 25 million tonnes is exported. Two thirds of the Canadian output is classified as thermal and one third as coking or metallurgical coal. The Canadian coal industry, like the industries in some other industrialized nations, has gone through a cycle of ups and downs. The current world vide recession and stable oil prices have somewhat dampened the plans for a further growth of this industry - albeit temporarily. No new mines are expected to be developed within the next few years. However the production is projected to increase to 60x106 tonnes in 1985 increasing to an estimated 75 to 80x106 tonnes by 1995. The Canadian mines are highly mechanized and are willing to employ the modern technology to maintain its competitive position in the world's coal market. This paper reviews the recent technical developments which continue to improve resource recovery and productivity.

Jan 1, 1986

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

Queensland?s underground coal industry, as a whole, has arguably the best gas monitoring systems in the world. Each mine utilizes real time, tube bundle and onsite ultra fast gas chromatograph systems. Queensland?s mining legislation has specific requirements for mine gas monitoring but there is no requirement for all three techniques. Industry has however identified the need for all three and adopted this as a standard, resulting in over sixty thousand gas results collected each day. Automated monitoring systems are programmed to alarm for gas concentrations, gas ratios and explosibility. These alarms are then used to initiate predetermined actions to take control of the situation and prevent the compromise of safety to workers and the loss of resources. Dedicated software packages have been developed to assist in the interpretation of the large volume of results generated. The real time systems are used for real time warning, essential for incidents such as belt fires. Tube bundle systems suit long term trending used for identification of the onset of spontaneous combustion or for the determination of explosibility during the routine sealing of worked areas. Gas chromatograph analysis is used to provide a complete analysis and provides results for hydrogen and ethylene, key gases used in the assessment of spontaneous combustion. It is also crucial during significant spontaneous combustion events and coal fires to use gas chromatography to determine the explosibility status of the underground atmosphere otherwise the severity of the situation is likely to be under estimated. This paper outlines the need for all three techniques for assessing the underground status and outlines advantages and disadvantages of each.

Jan 1, 2009

By Sang Ho Cho, Masaji Kato, Masaaki Yamamoto, Masaaki Nishi, Katsuhiko Kaneko

This paper presents a numerical simulation method to predict rock fragmentation and to verify a fracture mechanism by bench blasting. The rock fragmentation, which has been used as a means of the index to estimate the effect of bench blasting, affects the expenses for loading, conveyance and crushing of blasting muck piles. The developed numerical simulation method is based on the finite element method and fracture mechanics and includes the re-meshing procedure to express the fracture process of the rock mass. This paper discusses a procedure for a determination of size distributions of the results, which were calculated by numerical simulation, including the tines.

Jan 1, 2002

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

Industrial Minerals production in New Zealand is limited in both quantity and range, but imported in quantities that make New Zealand the world's biggest consumer per head of population. The use of industrial minerals is assured as both population and standard of living increase regularly. But to develop these minerals in the New Zealand environment requires the mineral, or its market (both local and export), to have characteristics that negate the remote geographical location. Volume and/or uniqueness can achieve this.

Jan 1, 1997

Kidd Mine in Northern Ontario is now producing from Stage 1 of the Mine D expansion project ? mining between 2100 m and 2700 m below surface. Planning for Stage 2 of the Mine D project is already well advanced and will see the mine extended potentially to 3100 m below the surface. To ensure adequate ventilation is maintained at such depths, two large axial fans have been installed on the 6000 Level (1800 m below surface) as exhaust booster fans to operate in series with the surface exhaust fans. The Kidd Mine 6000 Level Booster Fans are a unique installation with unique and often unexpected challenges. These challenges have been met and attacked through the combined efforts of mine and fan manufacturer personnel with a common focus.

Jan 1, 2009

By C Xuan, J H. Park, Q Wang, C Shen, D Kumar, W Mu

Dissolution of non-metallic inclusions in the metallurgical slag is of vital importance for cleanliness control of the steel manufacturing. With the development of high temperature confocal laser scanning microscope (HT-CLSM), new insights have been obtained due to its in situ observation characteristics, higher resolution and precise control. However, HT-CLSM measurement has the limitation, eg the slag composition cannot include high amount of transition metal oxides. In addition, it is time consuming for the experimental procedure and not so simple to succeed for every measurement. It is known that digitalisation has made a significant progress in recent years. Machine learning (ML), a sub-domain of artificial intelligence (AI), is the key enabling technology for the digitalisation of the material science and industry. The database for ML model is collected using almost all available HT-CLSM experimental data and subsequently the established database is trained by different ML methods. Unseen data is used as the benchmark of the ML model. Al2O3 dissolution is the main process to be predicted in the current study. A good agreement between the HT-CLSM data and the ML model prediction results show the possibility to apply ML in process metallurgy.

Jun 19, 2024

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008