Search Documents

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz

Embora a resistência ao desgaste seja geralmente a principal propriedade avaliada decorrente da adição de terceiros elementos em ligas Al-Sn, não somente os fenômenos tribológicos são responsáveis pela deterioração gradual das peças, mas também os fenômenos relacionados à corrosão. Dessa forma, o presente estudo objetiva analisar o efeito de características microestruturais formadas durante a solidificação transiente da liga Al-9%Sn-5%Zn na resistência à corrosão em solução 0,06M NaCl investigada por polarização potenciodinâmica e espectroscopia de impedância eletroquímica. Foi observada uma morfologia microestrutural caracterizada por dendritas da fase α-Al com concentrações de Zn tanto na matriz dendrítica quanto em regiões ricas em Sn localizadas nos contornos interdendríticos. A evolução dos espaçamentos dendríticos primários (λ1) também foi correlacionada com parâmetros térmicos de solidificação. Finalmente, constatou-se que a amostra com microestrutura mais grosseira, ou seja, λ1 = 89,6 μm, apresentou comparativamente menor densidade de corrente de corrosão e maior resistência à polarização.

Oct 1, 2019

By Joshua Alyson Freitas Ribeiro

Aços com teores eutetóides, tratados termicamente são usualmente utilizados em trilhos metroviários. Para que sejam atingidas as propriedades mecânicas desejadas para as devidas aplicações, o material pode ser submetido a alguns tratamentos térmicos, como, por exemplo, Recozimento Pleno, Normalização e Têmpera. Os tratamentos térmicos são de extrema importância, pois possibilitam uma grande versatilidade na utilização dos aços em geral. Neste estudo, as peças utilizadas são provenientes de um trilho metroviário e foram fornecidas pelo Laboratório de Pesquisa e Tecnologia em Soldagem da Universidade Federal do Ceará. Foram feitas análises metalográficas após diferentes tratamentos térmicos em peças do Aço SAE 1080 Fe-C com o objetivo de verificar os aspectos microestruturais e a sua inflências no comportamento mecânico das amostras e a alteração nas propriedades mecânicas. Pelo fato do material estudado ter uma matriz com composição perlítica de, aproximadamente, 100%, são mostradas as consequências devido à mudança nos espaçamentos interlamelares provocados pela aplicação de diferentes tratamentos e a influência da fase martensita na dureza do material.

Oct 30, 2017

By K. C. Armstrong, A. B. Cron, L. A. Melis

"The Johnny Mountain gold mine in northern British Columbia, owned by skyline Gold Corporation, has been in operation since August 1988. Mill operating difficulties at the start of the operation resulted in a depleted cash flow situation and quick improvements were required to generate a self-sustaining financial basis of operation. In October 1988, Melis Engineering Ltd. was contracted to identify metallurgical difficulties, implement necessary modifications, and undertake mill operations and personnel training in order to achieve production targets.This paper presents the operating difficulties which existed at start-up and describes the methodology used to overcome production problems. Metallurgical testing results are described along with the modifications made to the milling circuit to suit ore metallurgy. Plant changes led to the operation of a simple gravity/flotation circuit to recover gold as bullion and in a copper concentrate. Operation of the originally installed cyanidation circuit was discontinued. This contributed to substantial savings in operating costs and virtually eliminated environmental problems. PROPERRTY LOCATION ANR DESCRIPTIONThe Johnny Mountain mine site is located in northern British Columbia along the Iskuit River about 60 km east of Wrangell, Alaska and 275 km north of Terrace, B. C.. A location map is presented in Figure 1 and a site plan is shown in Figure 2. The complex is located on a mountain plateau about 3, 600 feet above sea level. The plateau is flanked to the north by Johnny Mountain and surrounded on the other sides by steep cliffs."

Jan 1, 1990

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By D. D. Hamilton

The ISMS program provided for the development and demonstration of equipment modifications for improved safety in both conventional and continuous coal mining systems. This report documents the success of the program in identifying accident hazards in underground coal mines with 4-to 8-foot seam heights, in designing modifications to reduce the hazards, and in demonstrating improved safety through extended underground use of the ISMS equipment.

Jan 1, 1977

By Euzebio De Oliveira

ONE of a recent batch of samples from the Serra da Baliza, in the state of Parana, Brazil, contained asphalt and a dark heavy oil; and workmen on the railway from Porto União to Uruguay discovered asphalt, coming from eruptives that outcrop along the Rio de Peixe. The occurrence f asphalt in the triassic eruptives of southern Brazil, however, has been known a long time, according to Dr. Gonzaga de Campos. It is generally believed that the Botacatú sandstone is always a hard vitrified rock, from the metamorphic action f. the overflowing eruptive contacts. In this region, however, the contact metamorphism is almost nil; the sandstone is slightly hardened in a narrow zone about 20 to 30 cm. wide. In many places, the sandstone is so friable as to be easily reduced to sand, which is used-.in, mortar for building in Guara-puava and Palmas. South and west from Porto União,. this bench of sandstone is about. 50 m. thick, and is capped by a heavy bed. f basic eruptives, many of which are amygdaloids. Dr. Geo: P. Merrill, after studying the triassic eruptives collected by the Coal Commission, reached the conclusion that. "All these rocks are of typical basalt-diabases, not in any essential different other than in structure. An interesting mineralogical phase is its paucity in olivine, which in many cases is completely lacking. Professor Hussak, who carefully studied these rocks and their accessory minerals, decided that in the dikes they are granular (diabase) and, that in the lava sheets, porphyritic (augite-porphyrite or melaphyre), and that the latter pass evidently to normal diabases and are always typical of effusive rocks. The examination f many slides from dikes and sheets leads us to adopt the opinion of Professor Hussak; the rocks of the dikes are of ophitic structure, while that of the sheets show a great variety f structure and may vary from almost granular to basaltic. The great paucity in olivine had been noted by Hussak, who classes as melaphyres, the porphyritic triassic rocks in Brazil which contain olivine.

Jan 4, 1921

By D. H. Horswill

The Red Dog Mine is the world’s largest zinc mine. It is located 145 km (90 miles) north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called the Northwest Alaskan Native Association (NANA) Development Corp. NANA acquired surface and subsurface title to this resource as part of its settlement lands under the Alaska Native Claims Settlement Act. In 1982, NANA entered into a lease agreement with Cominco. Cominco is an international mining company focused on zinc. It built and operates the Red Dog Mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language and traditions are as important to the NANA people today as they were in the past.

Jan 1, 2000

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

THE Synthetic Liquid Fuels Act (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Federal Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation,3 the Fischer-Tropsch synthesis,4 and nil stifle.5 The. Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because anal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form Will Ire valuable. The material will he presented in three parts. as follows I. United Stares Patents. II. United Kingdom, Australian, Canadian, and South African Patents. III. Other Foreign Patents. Part I appeared in early 1960. Part II follows.

Jan 1, 1962

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001