Search Documents

By W. H. Van Niekerk

The metal zinc has been around since only about 1400 AD. This may sound like a long time, but when compared to fellow base metals copper and lead, which were discovered in 5000 and 4000 BC respectively, it is evident that zinc is a fairly new kid on the block. This may also be the reason why many new facts and benefits of zinc are still being discovered. For instance, it has been discovered only in the last few decades that virtually no life on earth is possible without zinc. In this address it will be shown that zinc is not only very useful to mankind, but is in fact vitally important for all forms of life. It will be shown that zinc is natural, zinc is essential for life, zinc protects, zinc contributes to the well-being of society and that zinc is fully recyclable. It is therefore hoped, that by the end of this address, zinc will no longer be viewed only as the metal that is responsible for the nice colour of roofing sheets and steel buckets, but may indeed be man?s best friend.

Jan 1, 2005

This report is a compilation of all information obtained in accordance with the requirements of contracts S0122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies: Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gai-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated

Jan 1, 1974

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976

An enhanced gravity concentrator was installed in conjunction with an intensive leach reactor at the Sadiola plant in Mali last year and commissioned in December 2007. There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every ten per cent of gold recovered by gravity, there was a corresponding 0.1 per cent to one per cent additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall four per cent gain in plant recovery. With total gold recovery of 12 per cent in the gravity section, grades are increased from 3.54 g/t in the gravity feed to an average of 2 600 g/t in the concentrator feed to the inline reactor. The recovery of gold in the inline reactor is in excess of 98.5 per cent. This paper discusses the background to the project, the laboratory test work prior to the equipment selection, the operational results of the system, as well as the benefi ts of the future application of high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.

Aug 1, 2010

By E. F. Schnitzer, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

By I. Bhattacherya

Over the last three decades, the mining industry has been moving towards underground mechanized mining methods and the number of load haul dump (LHD) vehicles utilized has increased. The growth of mechanization and automation has benefited both workers and mining companies. However, due to the design constraints with LHD vehicles and the limitations of the operating environment, restrictions to operator visibility has contributed to a number of accidents, including fatal injuries. Past researchers have used the light filament technique to collect obscuration zones around mobile equipment and have produced 2D visibility charts (shadow diagrams) of this information. The light filament method involves manually collecting visibility data, which results in errors and is time consuming, requiring around three hours to complete. This research utilizes a MENSI GS100 laser scanner along with 3D modelling software (3Dipsos) to collect and process operator visibility profiles for underground mobile equipment. Results from this test work indicate that a laser scanner can be successfully used to rapidly collect this data and utilize this information for improved mobile equipment design from a visibility perspective. Nomenclature FERIC Forest Engineering Research Institute of Canada ISO International Organization for Standardization JACK Software for digital human modelling and ergonomics LHD Load haul dump vehicle LOS Line of sight MASHA Mines and Aggregates Safety and Health Association (based in Ontario, Canada) PVD Polar visibility diagram SAMMIE3D human modelling computer aided ergonomics design system WSIB Workplace Safety and Insurance Board

Jan 1, 2006

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By Crook KAW

New sedimentological and biostratigraphic data indicate that the Leron Formation in the Markham Suture Zone, Papua New Guinea (PNG) represented Pleist- ocene alluvial fan-delta deposition in shallow marine to lacustrine environments. The distribution of sedimentary regimes in the Leron Formation indicates that during collision zone evolution, various tectono-sedimentary regimes do not always track the movement of the triple-junction systematically as idealized by Crook's (1989a) model. The migration of various tectono-sedimentary regimes are also controlled and influenced by the effects of second-order geometric features of the convergent margins. Leron Formation in the Markham Valley represents late to post-collisional marine to fluvial molasse. Foraminifera indicate that the collision and concomitant suturing of the Markham valley occurred after 1.32Ma.

Jan 1, 1991

By Joan Weinberg

Real output expanded at a 3.0% rate worldwide in 1987, a slightly lower pace than the 3.2% rate in 1986. The decline was accounted for largely by slower growth in the U.S.S.R. and the East European countries, as well as in the developing countries (table 1). According to the International Monetary Fund, output of industrial countries output grew 3.1% and rose most strongly in Japan, the United Kingdom, and Canada (table 2). U.S. economic growth remained at 2.9%, the same as in 1986. Consumer and government spending declined in industrial countries, while gross fixed investment: rent increased. This increase in fixed investment expenditures could be attributed partly to lagged results of some 1986 developments: the fall in oil prices, declining interest rates, and exchange rate changes. The U.S. budget deficit, as well as the large external deficits and surpluses among major industrial countries, hindered further growth .2 A report from the Organization for Economic Cooperation and Development (OECD) indicates that the impact of the October stock market crash was short-lived because it hit economies that were growing strongly, anyway.3 The growth of output in the developing countries slowed in 1987; however, output declined in the fuel-exporting developing countries. These countries have been adversely affected by weakness in oil prices and the depreciation of the U.S. dollar. The weighted average of inflation rates in industrial countries--as measured by the [ ] GNP deflator, was 2.9% in 1987, down from 3.4% in 1986. Prices rose 3.0% in the United States, up from 2.6% the previous year. Inflation for 1988 is expected to remain slightly higher in the United States than in Japan and the Federal Republic of Germany because of recent exchange rates changes and the elimination of slack productive capacity and labor in the U.S. economy. Prices in developing countries as a whole rose more than 10 percentage points in 1987. Higher import prices, caused by

Jan 1, 1988

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

By Víctor Barrientos

El presente trabajo es un estudio realizado donde se determina la pérdida de ingresos de una empresa minera, producto de la detención de camiones y cargadores frontales en una faena minera a cielo abierto. El cálculo de esta pérdida de ingresos se realiza a través de un modelo que estima el volumen del movimiento de roca de la mina y los ingresos que este genera en función de la disponibilidad y rendimiento de los camiones y cargadores, y su interacción conjunta.

Sep 1, 2015

By O. H. Metzger

This is the second of two papers dealing with the construction and use of aerial tramways in the metal-mining industry. The first paper3/described aerial tramways in a general way and discussed the engineering principles used in tramway design. The purpose of this paper is to give a more detailed description of equipment and material rind to discuss construction and operating costs. ACKNOWLEDGMENTS The paper is based largely on data from actual operations. Metal-mine operators from many parts of the United States, Canada, Alaska, and Mexico contributed liberally.

Jan 1, 1940

By Juliovany Drumond

Este trabalho apresenta os resultados da produção do aço bifásico DP980 galvanizado a quente na ArcelorMittal Brasil, com foco no atendimento às propriedades mecânicas e microestruturais. Foram analisadas bobinas produzidas industrialmente de um aço bifásico baixo carbono com e sem adição de boro, e também amostras para simulação de recozimento. A análise foi baseada nas propriedades obtidas no ensaio de tração e também na microestrutura. Foi observado que o aço com adição de boro apresentou propriedades mecânicas mais elevadas que o aço sem a adição deste elemento, e este aumento está diretamente relacionado à maior fração volumétrica de martensita encontrada neste aço. Este fato está ligado à segregação do boro nas interfaces ferrita / austenita durante o recozimento intercrítico, evitando assim a nucleação e crescimento da “nova” ferrita, com um consequente enriquecimento de carbono na austenita. Esta austenita mais enriquecida de carbono gera uma maior quantidade de martensita na microestrutura final. Diante disso, o aço DP980 produzido industrialmente com adição de boro apresentou melhores propriedades mecânicas e microestruturais, sendo compatível com os requisitos demandados atualmente pela indústria automotiva, quando galvanizado a quente nas condições de processo estabelecidas neste estudo.

Jul 30, 2018