Search Documents

By James L. Hendrix

The applicability of a rotating drum with an attached trommel as a flocculation dewatering device of Florida phosphatic claywastes was studied. Several experiments were conducted in order to determine the important fabrication and operating parameters. Results from the experiments indicated flint the dosage of polyethylene oxide required to form a satisfactory product cake could be reduced by using the rotary drum, which introduces less shear stress into the fluid than a constant stirred tank mixer. It was found that the length of the mixer was the most important parameter. Increased length increased the retention time the flocs stayed in the mixer without dewatering. Such increased time decreased the stability of the flocs. Through analysis of residence time distribution data it was found that the longer mixers approached plug flow characteristics. Other important parameters were trommel length and rotational speed. Mixers from 10 cm diameter to 35.6 cm diameter were tested with good results.

Jan 1, 1982

By Olman Hee

This study investigates the identity and relative importance of factors affecting the future demand for phosphate rock, potash, and nitrogen. The main objective is to analyze demand relationships for these chemical raw materials for some specified past period, and to utilize this information to make projections of consumption into some designated future period. The end-use approach is used, which divides total consumption of each chemical raw material into agricultural, industrial, and export use. Multiple regression analysis is employed to statistically measure the relative effects of the different factors on consumption in each end use. The general method centers on the construction of a consumer demand model, the fitting of the respective equations in the model, and the interpretation of the statistical results. Direct and cross price elasticities of demand are computed for each end use of the chemical raw materials. These give an insight into expected changes in consumption with respect to given changes in price. The results of this study indicate that price, consumer income, and level of technology are factors which measurably affect consumption of chemical raw materials. For phosphate rock and potash, the agricultural and industrial end uses showed an inelastic demand, whereas for nitrogen, all end uses (including export use) exhibited an elastic demand. Among the chemical raw materials, average annual growth of consumption of nitrogen for agricultural and export uses to 1980 is expected to be notably higher than that for phosphate rock and potash.

Jan 1, 1969

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By C. W. Owings

The number of major coal-mine explosions occurring annually in the United States is decreasing, due mainly to fuller recognition of explosion hazards in coal mines and knowledge of methods to prevent them, which can be attributed largely to the dissemination of information by the United States Bureau of Mines, State departments of mines, and other coal-mining agencies. Conditions vary considerably from one coal field to another; consequently, outstanding causes of and methods of combatting explosions vary, also. The Safety Division of the United States Bureau of Mines is making a critical study of coal-mine explosions in the various coal-mining States, and an analysis of the results is published as each study is finished. It is believed that, with completion of the series enough information will be at hand which, if applied, will prevent all coal-mine explosions. ACKNOWLEDGMENTS The data in this circular are based on records of the United States Bureau of Mines and the Industrial Commission of Ohio. The cooperation and assistance of T. P. Kearns, superintendent of the Division of Safety and Hygiene of the Industrial Commission of Ohio, and of James Berry, chief inspector of the Division of Mines of Ohio, is acknowledged.

Jan 1, 1937

By P J. Dailey, S L. Burchell, R F. Chiappetta

In recent years, high-speed motion picture photography has become a powerful diagnostic tool and technique to study, analyze, evaluate, and aid in blast designs. Production blasting, typically lasting less than two seconds, requires an extended time base for observation and clarification of short-lived phenomena. Information obtained from high-speed photographic analysis is categorized into two main groups.

Jan 1, 1989

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961

The mineral industry of Benin contributed less than 1% of the 1977 gross domestic product (GDP), which was estimated at $500 million.' Other than limestone and salt, no exploitable mineral deposits have yet been discovered in Benin, which has been rated by the United Nations as one of the world's least developed nations. In 1977, the economy was further weakened by petroleum price increases and severe drought. The country continued to depend on foreign assistance, which averaged $20 million per year, to finance development projects. The country's first 3-year plan, which was put into operation in October 1977 after many delays, allocated more than $1 billion to projects in infrastructure, agriculture, and light industry. The most important infrastructure project was the expansion and modernization of the port of Cotonou, valued as an entrepôt port for the transit of goods to the neighboring countries of Niger and Nigeria. Plans called for an increase in handling capacity to 1 million tons of cargo annually, the improvement of port and cargo handling operations, and the upgrading of the efficiency of the Port Autonome de Cotonou (PAC) management system. The $46 million project was to be financed by a consortium led by the International Bank for Reconstruction and Development (IBRD) and including Canada, France, Nigeria, and Abu Dhabi. Construction was scheduled to begin in 1978 and be completed in 1980.

Jan 1, 1981

By Joe Maher

[ ]

Jan 1, 1976

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

Nickel-bearing ores in North-east Dundas have been described by A. McIntosh Reid1 as occurring at the margins of narrow dykes of gabbro, norite, peridodite and pyroxenite, which are intrusive into the Dundas series of slates, quartzites and breccias. They occur chiefly in the neighbourhood of the Five Mile, near Zeehan, as small, narrow ore-bodies which are mostly less than 100 ft. in length.The ores are massive sulphides containing pyrrhotite, chalcopyrite, pyrite and the nickel sulphide, pentlabdite.A less common nickel-bearing mineral, gersdorffite, has been recently found in an adit, which is marked on Reid's geological plan of Dundas as the Hecla mine, 30 chains south of the crossing of the North-east Dundas tramway, over the Great Northern Creek, and at an, elevation of about 350 ft. above the tramway. The occurrence is in a lode traversing the Dundas slates and quartzites, and is situated, according to Reid's plan, about 20 chains beyond the northern extremity of a narrow basic dyke which is continuous for a distance of two miles in a south-westerly direction.The mine eonsists of a prospecting adit following the course of a lode for about 275 ft. in a direction a little west of south. The low values of the lode are indicated by a bulk sample from a shallow winze about 100 ft. from the entrance which is reported by Reid to contain:

Jan 1, 1935

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.' If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i'reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well 'flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011