Search Documents

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

Workers in underground stone mines have a high fatality rate caused by falls of ground from the mine roof or rib. NIOSH recommendations to reduce ground fall injuries and deaths address baskets, mechanical scalers, mechanical bolters, drill steel changing, personal protective equipment, and training. Description of Exposure An informal National Institute for Occupational Safety and Health (NIOSH) review in 1998 identified approximately 17 new underground limestone operations in vari¬ous stages of planning; as many as 35 new underground stone mines are expected by 2005. Many of these new underground stone mines will employ new or inexperienced workers with minimal knowledge of the hazardous conditions that exist underground. Workers in underground stone mines have a fatality rate nearly 20 times that of workers in the manufacturing sector. Three quarters of the fatalities in underground stone mines are caused by falls of ground from the mine roof or rib (Figure 1) [Statistical Abstract of the United States 1985-1999; MSHA 1983-1999]. During 1983-1999, nonfatal ground falls resulted in 140 injuries, or 15% of all underground, lost time stone mine injuries. These nonfatal ground fall injuries resulted in more than 13,800 lost workdays (one third of all lost workdays). Ground falls generate more disabling injuries and time away from work than any other type of incident. [ ]

Jan 11, 2003

By B. Yarar

The critical surface tension of wetting (?c) of Cu2S, FeS2, PbS, and MoS2 were determined by plotting flotation recovery versus YLV which was arranged by methanol, and Extra-polating to % R = 0. ?c values ranged from 26 dyne cm-1 for MoS2 to 49 dyne cm-1 for PbS and elemental sulfur gave a value of 31.5 dyne cm-1. Minerals exhibiting natural flotability of different extents, could be separated from their mixtures in the absence of conventional flotation reagents, but controlled ?LV. Correlations between non-stoichiometry and degree of natural hydrophobicity for MOS2 are also reported in this paper.

Jan 1, 1983

Study on Desulfurisation and Deashing for Medium-High Sulfur Coal Using Shaking Table As important coal resources, medium- high sulfur accounts for a significant part of the coal reserve in China. The environmental regulations and fuel standard requires sulfur and ash to be removed before it is used, so as to save energy and decrease the emission. Therefore, the effective desulfurisation and deashing technologies are urgent needed. However, due to the local characteristics of the coal, specific technology with optimum operation parameters is required to develop for different local coal. Qinglong is a district of Guizhou Province, which has large medium to high sulfur contained coal reserve. In this paper, medium-high sulfur coal is sampled from Qinglong, Guizhou province. Some basic characteristics such as the mineralogical composition of the coal rock, the monomer existing state and the granulometric composition are determined by X-ray diffraction quantitative analysis and polarisation microscope analysis respectively. Adopting the classified feed method, shaking table tests show that the feed pulp concentration is 20 per cent, the stroke is 13mm, the frequency of the stroke is 380 per min, the cross slope is 3¦ and the volume of wash water is 5.2 L per min. Under such condition, aggregate processed coal yield is 72.87 per cent and sulfur content decrease to 1.31 per cent With shaking table technology of 'First stage rough and intermediate further fine benefication', the yield of concentrate coal increased from 72.87 per cent to 81.21 per cent, while the sulfur content reduced to 1.35 per cent.

Sep 13, 2010

By Royal Preston Jarvis

minerals of different specific gravities. It is simple in construction, easily operated, capable of treating large quantities in a short time, and highly efficient under various conditions. The question, whether the material to be jigged has first been sized, determines the two principal methods of jigging. Jigging preceded by close sizing, generally known as the Continental or German system, involves a more or less elaborate series of screens or trommels, with attendant cost for installation, operation, and repairs. Jigging without sizing, known as the English system, is, according to Munroe,1 a development of the hand-jigging formerly employed in Cornwall . and introduced by English miners to this country." In its simplest form, the method consists in jigging an ore-mixture previously crushed to some maximum size (although, in some cases, even this preliminary is omitted) oil a relatively coarse sieve, and then jigging again on a filler sieve, the material passing through the first sieve and bedding. While many modifications have been necessary to adapt it for use in mills of large capacity, where hand-work was necessarily, replaced by machines, the principle remains the same; the fact that the English system has been successfully employed, both in this country and abroad, is well known; and arguments have been made for its efficiency and applicability in a wider sphere than it has occupied hitherto. II. REVIEW OF PREVIOUS INVESTIGATIONS. The fact that treating a mixture of minerals under jigging conditions increased the amount of mineral saved, or, as Professor Richards aptly terms it, 1 ?the extra jig-catch," has long been known. To account for this fact a number of theories have been proposed. The work of Rittinger2 in this field has, for many years, been a classic in the literature of ore-dressing. For the purposes of my present paper, however, the work of two American investigators, Prof. H. S. Munroe and Prof. R. H. Richards, is chiefly concerned. Professor Munroe has given the results of an elaborate series of experiments,3 and his deductions, based largely oil theoretical grounds, of this work. After reviewing briefly the two systems of jigging, followed by a discussion of Rittinger's formulas and

Sep 1, 1908

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976

By M. B. C. Brandt

Focal depths of 15 tectonic earthquakes and 9 mine-related events were determined for South Africa using data recorded by the South African National Seismograph Network. These earthquakes and events were relocated by means of the Hypocenter program using direct P-waves (Pg) , critically refracted P-waves (Pn) , and first-arrival S-waves for the magnitude range 3.6 ?? ML ?? 4.4. Focal depths were first determined by means of the minimum root mean square (RMS) of the differences between the measured travel times and those predicted using the velocity model. The depths for tectonic earthquakes had a 2 km ?? D ?? 10 km range and an average depth and standard deviation of 6.9 ± 2.3 km. Depths for minerelated events ranged over 0 km ?? D ?? 7 km, averaging 3 ± 2.3 km. Next, arrival times for the additional regional depth phases sPn , PmP, sPmP, and SmP were measured. Focal depths were re-determined for the relocated epicentres, with the minimum variance (i.e. spread) of the differences between the measured travel times and travel times predicted by means of the Wentzel, Kramer, Brillouin, and Jeffreys (WKBJ) method for synthetic waveform modelling. Depth ranges were 4 km ?? D ?? 7 km (average 5.9 ± 1.2 km) and 1 km ?? D ?? 4 km (average 2.4 ± 1.2 km) for tectonic and mine-related events, respectively. The derived depths were verified for one tectonic earthquake with synthetic-to-recorded-waveform fits using the WKBJ synthetic seismogram software for the abovementioned regional phases. The focal mechanism parameters for this earthquake source were obtained from the National Earthquake Information Centre. Focal depths were estimated for nine stations by visually comparing synthetic waveform phases with recorded waveforms, ranging from 5 km to 8 km.

Jan 1, 2014

The observation of lower-than-predicted Fe/Cu ratios in the cementation of copper on iron in tests at elevated temperatures indicated that some other reaction was contributing to the reduction of cupric sulphate in addition to the reduction by elemental iron. Experiments showed that the copper sponge, which initially formed on the iron, subsequently reduced the cupric sulphate giving the products cuprous oxide and sulphuric acid.Tests were undertaken to determine the rate and equilibrium conditions of the reduction reaction with variations in the types of the reducing agent and solution parameters. The reaction first became apparent at temperatures above 50°C and as it ceased at pH 1·8 it was possible to induce further reaction by alkali addition.

Jan 1, 1974

By Joseph J. Yancik

An exchange of coal mine specialists was made with the USSR under an "Agreement on Exchanges and Cooperation in Scientific, Technical, Cultural, and other Fields for 1972-73," which was signed by President Nixon and Chairman Breshnev on April 11, 1972.* This exchange, in the field of coal mine safety and scientific research in hazard control technologies, was one of 16 technical exchanges covered under the above agreement. A six-man USA delegation visited the Soviet Union from September 9 to September 21, 1973. The delegation visited four deep mines, three in the Donets Basin and one in the Moscow Basin, a State Safety Research Institute, a Mine Research Station and associated Research and Design Institute, two Research and Design mining equipment institutes, and a Trade Union-sponsored health sanitarium. In Moscow, the delegation received a briefing on the Soviet coal industry from First Deputy Minister Vladimir Fedanov. A similar briefing was given to us on the Donets coal basin by the Deputy Minister S. Saratikyanz of the Ukrainian Coal Ministry. Lengthy technical discussions were held with the mines staff and research personnel at the institutes we visited. In addition, we had detailed discussions with key staff members of two combinats "Donetskugol" and "Tulaugol." In all these meetings, principal topics were matters of safety related to hazards associated with face mechanization, coal transport, methane gas control measures, gas outbursts, coal and rock outbursts, fire fighting add control, explosion suppression and control measures and other related hazard factors. There was also much discussion on miner training, miner's attitudes toward safety and accident prevention practices, and preparation and enforcement of safety rules and regulations. The delegation was very warmly received and constant attention was given to our needs. Our numerous questions were answered with candor although quite often in not as much detail as we would have liked.

Jan 1, 1974

By Raffaele Alves Paranhos

Devido à alta competitividade no mercado siderúrgico se faz necessário à otimizaçãodo processo como forma a atendermos a demanda de produção com um menorcusto de transformação. Nesse contexto, foi utilizado para desenvolvimento dotrabalho a metodologia DMAIC e os conceitos do “LEAN”. O objetivo do grupo foiestratificar o custo de produção do equipamento e atuar nos principais fatores, tendocomo princípio a redução do desperdício, aumento da produtividade da mão de obra,aliada a produtividade de tonelagem de material. Na estratificação do custo deprodução identificamos o “Rendimento metálico” como sendo o fator maissignificativo e propomos ações internas que contemplaram alteração de programade automação para melhora do descarte da cauda (Final) da bobina e com issoatingindo valores recordes de aproveitamento material acabado. Fizemos reduçõesde lead time do nosso processo eliminando os tempos que não agregam valores,aumentando a produtividade do equipamento. Com este trabalho conseguimosreduzir consideravelmente o custo de transformação do equipamento, além, deaumentar sua capacidade produtiva.

Aug 16, 2017

By Nick Lewis

Farce Mining of Texas is a surface coal mine located in Laredo, Texas. Farce mines and sells approximately 600,000 tons /year of bituminous coal. A map showing the location of Laredo is provided in Figure 1. As shown, Laredo is located on the border between the United States and Mexico. The mine property runs to the Rio Grande River, the border between the two countries. Farce pumps water from the Rio Grande for use in their coal preparation plant. Laredo’s climate is quite dry with annual rainfall averaging about 12” per year. Also, due to the southern location, Laredo is quite hot. It is common for the temperature to reach 100” F in March and maintain these temperatures through September.

Jan 1, 1994

VISIT TO HENDRINA POWER STATION AND OPTIMUM COLLIERY A visit to Hendrina Power Station and the Optimum Colliery, contractually committed to supply the coal for the power station, took place on the 20th September, 1972. INTERNATIONAL IRON AND STEEL CONGRESS This congress will be held in Dlisseldorf from May 23rd to 30th, 1974. The main theme is "Metallurgical Technology of Iron and Steplml1king".

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

The Morning Star diorite dyke has been subjected to two periods of mineralization. The earlier, genetically related to the dyke magma, gave rise to a weak chalcopyrite-pyrrhotite-pentlandite-gold mineralization in a narrow zone, up to 25 cm. wide, which parallelsthe nearby western (hanging) wall of the dyke. Subsequently a set of conjugate shears formed in the dyke as a result of tectonic movements. Gold-quartz veins formed in these shears giving rise to the classical "ladder veins" of the Morning Star mine. On either side of the veins ("floors") the diorite has been bleached for up to 3 ft. This involved introduction of much CO. and some K"O, and S with abstraction of SiO. and FeO, giving rise to carbonates, sericite, zoisite and pyrite. The veins consist of quartz with minor amounts of albite and carbonate, together with pyrite, arsenopyrite, pyrrhotite, chalcopyrite, sphalerite, tetrahedrite, galena, bournonite, boulangerite and gold. Spectrographic analyses of gold show that the suite of trace elements is consistent throughout the mine.INTRODUCTIONThe gold-quartz veins of the Morning Star Gold Mine, at Wood's Point, Victoria, are a classic example of the "ladder vein" type of deposit. The structure of this series of repeating quartz veins or "floors", some barren and some productive, occurring in a set of conjugate shears which transect a "dyke bulge" of diorite (Fig. 1), has been described on numerous occasions as mining has progressed and figures in the textbooks (Whitelaw, 1905; 1916; Junner, 1920; Lindgren, 1933; McKinstry, 1935; 1942; 1949; Kenny, 1949; Hills, 1952; Clappison, 1953) ; but there has been no study of the mineralization apart from that in Junner's (1920) general study of the Walhalla-Wood's Point Goldfield, made at a time when mining had not developed below the 400 ft. level,. and the mine was dormant.

Jan 1, 1958

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.'-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005