Search Documents

Significance of Ion Interactions in Flotation in Saline and Brine Solutions

Sep 13, 2010

By Andrew St. Amant

This report reviews the first three "investigative and concept generation" phases of the referenced contract, and details task performance of Phase IV. This last phase integrated the most promising concepts from Phases I, II, and III into a prototype detailed design which was manufactured, and then tested on a mine locomotive. The concepts developed during the first three phases provided "Improved Pole Tracking," automatic "Rapid Pole Retraction" in the event of dewirement, and servo-operated "Remote Pole Repositioning" on the trolley wire. The Appendix of this report supplies detailed information for the design and construction of the prototype system which is comprised of an RCB (Remotely Controlled Base subassembly), an RCL (Remote Control Lever subassembly) and an SAU (Servo Amplifier Unit) subassembly.

Jan 1, 1980

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By S. Cossio, J. L. Noyola, R. Espinosa

"Minera Penmont’s La Herradura is a joint venture between Industrias Peñoles, S.A. de C.V. and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with a two-stage crushing plant and heap leaching facility. Gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130 000 oz gold per year and its treatment capacity is approximately 22 000 t/d. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to coarse visible gold, which in some cases ranges from 100 to 600 microns.Sampling and assaying protocols were established during exploration and prior to start-up of operations, based on nomographs developed from early heterogeneity tests. However, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block consisting of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to start-up of operations (existing) and the new protocol (leaching). In the existing protocol, sub-sampling is done through riffle splitters, and coning and quartering. Fire assaying was used to estimate the gold content on a 50 g sample. In the leaching protocol, a 12 000 g sample of bottle-rolled cyanide was leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this rotary sampling protocol and for comparison purposes, gold assays were also repeated using the leaching protocol.Test results were compared in three groups: < 0.3 g/t (below cut-off), 0.3 to 0.8 g/t, and >0.8 g/t. Overall, results show that the protocol established prior to start-up of operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2004

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey&apos;s success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013

By Tumilty JA, Schmidt CG

Sulphide ion is a powerful poison in gold cyanidation, however, the detrimental effect is less severe in plant practice. This is thought to be due to the presence of depassivating elements in the ore, mainly lead. Trace amounts of lead can counteract the poisonous effect of considerable amounts of sulphide. The reaction is instantaneous and is likely to be a direct involvement in the electrochemical surface reaction. Lead addition cannot be regarded as an all-round cure when experiencing poor leach efficiencies. A possible beneficial effect depends on the mineralogy of the ore and has to be determined individually for every material.

Jan 1, 1989

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By Judy B. Jones, Bradley A. Crenshaw, Theodore DePooter

This paper reviews groundwater issues leading to a secondary grouting program at the Chattahoochee Tunnel that was implemented subsequent to the contact grouting program. The secondary grouting program was developed based on infiltration data, geology, and testing programs. This paper includes a brief description of the geological features encountered, as well as describing the grouting program. The success of this grouting operation has been quantified by several methods, and is presented to help others project the costs and benefits of this type of program. Review of initial results and refinements of techniques are also discussed.

Jan 1, 2005

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:C&#243;rdova, E, Brzovic, A and Gonz&#225;lez, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By Joelma Krugel Brites

Com a perspectiva do uso de aços API em ambientes sour service, o controle de inclusões e precipitados é essencial para bom desempenho. A precipitação de carbonetos e nitretos de Nb e Ti, assim como a formação do MnS foram analisados criticamente em aços de alta resistência e baixa liga – HSLA- com Mn entre 0,3 e 1,6%, Nb 0,02-0,1%, S 0,001-0,005% e Ti 0-0,02% em peso. Os valores da temperatura de precipitação do MnS, Nb(C,N) e Ti(C,N) foram obtidos por meio do software ThermoCalc™. A partir desses resultados, possíveis tendências da precipitação foram discutidas e relacionadas com a temperatura de não-recristalização, traçando um comparativo entre temperaturas de processo e precipitação. Três aços produzidos com a composição estudada atenderam os requisitos mecânicos de tração da norma API 5L X65M.

Oct 30, 2017

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985

By Ebrahim Ghasemi

Problem statement: One of the most challenging safety problems in room-and-pillar coalmines is controlling roof falls during retreat mining. Roof falls not only cause both fatal and non-fatal injuries to miners, stoppages in mining operations, and equipment breakdowns, but also results in the inefficient recovery of coal reserves. Approach: Sufficient awareness of effective parameters related to roof falls is an important factor in roof control. In this study, the major contributing parameters on roof falls during retreat mining are introduced based upon experience and judgment acquired from extensive retreat mining case histories and a review of relevant literature. Key findings: The main roof fall parameters in retreat mining can be divided into three categories: geological, design, and operational. Key conclusions: The design and operational parameters can be controlled by the engineer and/or operator. By the appropriate selection of these parameters in the design and implementation stages of retreat mining, the roof fall risk can be decreased to an acceptable extent.

Jan 1, 2012

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By Welington Bermudes Merelles

A ArcelorMittal Tubarão, unidade de produção integrada de aços Planos, faz parte do Grupo ArcelorMittal, maior produtora de aço do mundo. A empresa localizada na Região metropolitana de Vitória (ES), tem como principais produtos bobinas a quente e placas de aço. Como resposta ao cenário econômico do País, que atualmente se posiciona com baixa atividade econômica e em busca de manter a perenidade de seus negócios, lançou um Programa para identificar e eliminar “desperdícios”, baseado na metodologia Lean Thinking/ Manufacturing. Uma das iniciativas, apontadas como oportunidade de aumento de produtividade foi a etiquetagem das Placas de aço em substituição ao processo tradicional de Marcação e Pintura das placas. Esta mudança no processo de identificação de placas, proporciona maior produtividade na área de Condicionamento de Placas e a possibilidade de aumentar a produção com menos recursos e custo operacional.

Oct 30, 2017