Search Documents

By Gunn S. G, Wilson E. G

Studies by Telecom showed that the existing cable tunnel system in the Melbourne C.B.D. required expansion in order to meet the future telecommunications needs of the City. Due to physical locations of the various telephone exchanges in the CBD, together with a necessity to connect into existing ATC tunnels, a network of low cover small sized tunnels was proposed to maintain and extend the existing telephone cable network. This paper reviews the feasibility studies, design criteria and constructional aspects involved in building 5 tunnels (total length of 1850 m) and 13 chambers (4 open cut and 9 underground)-together with ancillary works, which form part of the new cable tunnel network.

Jan 1, 1981

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Meinhart, J Rodler, I Katolicky

The ever increasing number of vehicles is leading to slow-moving and even stationary traffic sitting longer in traffic jams over extensive city areas. This traffic situation causes a sharp increase in pollutant emissions from vehicles, and high levels of pollution usually result throughout the built-up area. Reducing the pollution level by using traffic routing measures to speed up the flow of traffic in the existing street network is only possible in exceptional cases.In many cases the only option for achieving a significant improvement in traffic conditions is to shift the traffic underground using a road tunnel or underpass. Such tunnel routes suck off the traffic from large sections of the city, thereby easing the overall traffic flow. Thus on the one hand it produces a sharp reduction in pollution levels in the area of the tunnel route, but on the other hand it can result in locally increased exhaust pollution levels from longer tunnel systems that require mechanical ventilation. The air extracted by the ventilation system is blown out into the atmosphere either directly through the tunnel portal, or via a venting tower. Pollution can therefore occur in the area surrounding such exhaust air outlets.Thus if a tunnel is planned in a city, then closer investigation is required of both aspects: the reduction in pollution in the area of the tunnel route thanks to relocating the traffic and easing congestion, and the increased short-range pollution around the tunnel portals (shafts).

Jan 1, 1999

The 5.6 km Canning Tunnel was constructed to improve water supply from Canning Dam to the Perth metropolitan area. The site area is in the Darling Range which is essentially a laterite-capped plateau-remnant underlain by Archaean granitic rocks, intruded by dolerite. Two arrangements were available. After geotechnical investigations which included geological mapping, seismic refraction geo- physics, diamond drilling and mechanical rock testing, a single tunnel was selected in pre- ference to two short tunnels and a connecting pipeline. The tunnel is hydraulically equivalent to a fully lined tunnel 1.83 m in diameter and 5 580 m long. The alignment diverged from a straight line so that the initial upstream section was almost normal to the contours which allowed for minimal support requirements in a weathered zone. Although steel and con- crete lining was needed at both ends, the main section of the tunnel was unlined except for a concrete floor. A sand and rock trap with a capacity of 46 m3 was constructed near the outlet portal to collect debris and sand down to a size of about 2 mm. Portal excavations were in highly to completely weathered rock which extended 56 m into the tunnel at the upstream end, and 18 m at the downstream end. Conventional drilling and blasting were used for tunnel excavation with survey control by laser. Breakage lEngineering Geologist, Mines Department, Perth, W.A.

Jan 1, 1976

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By T Ireland

The Rosedale Outfall Project utilised an earth pressure balance (EPB) tunnel boring machine (TBM) for only the second time in Auckland. Although the tunnel was excavated fully through East Coast Bays Formation (ECBF), the downhill gradient along with some unexpected areas of extreme water posed some significant challenges during construction.The Rosedale Waste Water Treatment Plant Outfall Tunnel project was commissioned in response to the growing needs of North Shore City, New Zealand. The outfall tunnel comprises a 3 km long segmentally lined tunnel and a 2.1 km buried marine pipeline, and discharges 2.7 km offshore. The capacity of the new outfall is 6 m3/s compared to the existing outfall capacity of 1 m3/s.Following previous project experience, and with the tunnel located along its full length in the bedrock weak sandstone/siltstone bedrock of the East Coast Bays Formation, tunnelling conditions were expected to be benign. However during construction six high inflow events were encountered, including a full face (3.4 m diameter) of Albany Conglomerate over a 48 m length of tunnel. This material comprised cobbles in an uncemented sand matrix, and inflows were recorded at over 25 L/s.This paper describes the design challenges on the project including the design of a steel fibre reinforced segmental lining for internal pressures. The specification of the machine is discussed including the modifications required to enhance the risk mitigation measures already in place. The ground conditions encountered are discussed and have improved the knowledge of the range of conditions that can be expected in Auckland.Despite the challenges presented during construction, excellent progress rates were achieved and the tunnelling was successfully completed ahead of program.

Mar 8, 2011

By Sun Y. L, Jiang J. J, Lu S. L

A distinguishing feature of tunnels in squeezing rocks is that a large deformation of the surrounding rocks takes place slowly and gradually, often called squeezing phenomenon. It is different from the rocksbursting phenomenon during which the deformation of tunnels occurs instantaneously when the resulting stresses exceed the strength of the surrounding rocks. The squeezing phenomenon has received great attention in the field of rock mechanics and tunnelling recently. The mechanism and various factors related to the large deformation and failure of tunnels in squeezing rocks are discussed in this paper on the basis of field investigations and laboratory model tests. The relationship between the deformation of surrounding rocks and support of the tunnels in squeezing rocks is presented in the form of numerical modelling.

Jan 1, 1995

Truck fires in a tunnel can create heat release rates (HRR) significantly higher than 100 MW. Because of a fast spread of smoke and heat the self-rescuing period is shortened significantly. Furthermore, it was experienced that firefighters are not able to approach the fire because of enormous heat and radiation. As consequence, the fire may spread to adjacent vehicles, which is reported for distances of more than 50 m. Tunnels can be damaged severely by fires and the repair works causes long closing time of tunnels. In addition to direct costs for the refurbishment of the tunnel, further economic losses will occur due to the closure time. Conventional deluge systems in Japanese and Australian road tunnels have been known since the 1960s. During the last years the research work was concentrated in the development of more effective and cost-effective solutions based on water mist technology. Orientating fire tests as well as specifications of minimum requirements were carried out within the European research project UPTUN. This basic work was extended by the safety of life in tunnels (SOLIT) research project, funded by the German government. The scope of SOLIT was not only to study the effects of water mist fire suppression systems in tunnels, but also the interactions with other safety systems, such as fire detection, passive fire protection or ventilation. Furthermore, the integration of active fire suppression systems into a holistic tunnel safety system was part of the work program. Within this research project a large-scale fire test program with more than 50 fire tests, including 25 truck fires with a potential HRR of almost 200 MW, was carried out in the test tunnel of San Pedro des Anes (Spain). Furthermore, a two-week testing and training period with the Madrid Fire Brigade was carried out after the SOLIT program. Two fundamental results were achieved during the fire tests:Primarily, water mist systems are able to control the HRR of fires in tunnels, so the atmosphere will be improved significantly. Hazardous effects of toxic smoke on people will be reduced and due to the reduction of temperatures and radiation, a firefighterÆs approach is improved significantly. Furthermore, the fire spread will be hampered and the thermal load on the building structure also be reduced. Secondarily, due to positive interactions with the ventilation system, the effectiveness of a tunnel ventilation system, longitudinal as well as semi-transversal, is increased significantly. Based on the results of the SOLIT research project, a water mist system was applied into several parts of the M30 tunnels in Madrid. As a basic principle the technical equipment and the methodology of implementation comply with the UPTUN 251 guidance, recommending minimum standards for water-based fire suppression systems in tunnels.

Jan 1, 2008

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Weeks

Melbourne Water Corporation, through the Pipelines Alliance, has commenced construction of a new drainage pipeline to provide additional flood protection within the Sandgate Avenue Main Drain catchment, in order to mitigate against the risk of flooding of Frankston’s central activity district (CAD).The project involves the construction of a 1550 m long, 2.5 m internal diameter tunnel, commencing upstream at the Monash University Peninsula Campus and traversing approximately west to the outlet located at Kananook Creek. The tunnel was excavated by a dual slurry-earth pressure balance tunnel boring machine (TBM), with the depth to tunnel crown ranging from 0.7 m to 14 m below the natural surface level. The TBM navigated 500 m radius curves, with a maximum drive length of 608 m. The tunnel lining consists of 2.5 m internal diameter, 250 mm thick reinforced concrete jacking pipe.The geotechnical conditions along the tunnel alignment consisted of mixed face ground conditions, predominately clay, with clayey sand and sandy clay and some sand deposits near Kananook Creek.This paper presents the challenges associated with the operation of the slurry separation plant during tunnel construction. In particular, the paper focuses the impact of slurry separation on tunnel advance rates, the lessons learnt during construction with regards to slurry separation and on the decision to adopt a dual slurry-earth pressure balance shield TBM. In addition this paper highlights the importance of having a thorough understanding of the slurry separation requirements on a slurry TBM project prior to selecting the necessary plant.

Mar 8, 2011

By I Lamb

Past experience of ground settlement and groundwater monitoring for tunnelling projects in Melbourne has provided an appreciation of the value and importance to owners of establishing a broad baseline monitoring program of the ground surface movements and groundwater movements well in advance of the commencement of any excavation and tunnelling activities. For the Northern Sewerage Project (NSP) tunnels in the northern suburbs of Melbourne, a baseline monitoring network of ground settlement points and groundwater wells was established in early 2006, 18 months prior to the commencement of project construction, and has continued throughout the tunnelling and project construction activities. This baseline monitoring network provides insights into the superposition and interpretation of both tunnelling and non-tunnelling effects, such as seasonal effects, which result in ground settlement.In the case of the NSP the baseline monitoring and construction phase excavations coincided with several years of drought. The reduced rainfall developed overall downward settlement trends project wide that could easily be mistaken at the local site level to be construction effects if the baseline monitoring was not available to show otherwise. There are lessons to be learned from the NSP experience for tunnel projects where there are variable surface soil types and where project-specific settlement criteria are to be established for the protection of property prior to construction.This paper presents examples of the baseline monitoring, how the tunnelling-specific settlement was identified and determined, and what this means in terms of how settlement criteria should be established and set for project consenting and in the construction contract documents.

Mar 8, 2011

By L Drowley

The Adelaide Desalination Plant (ADP) draws raw sea water into the facility and returns saline concentrate to the Gulf St Vincent via subsea conduits. This paper describes the detailed design and construction methodologies developed for the cross connection tunnel excavation. The paper concentrates on key design elements which include:· lateral breakout support of the segmental tunnel lining,· ground improvement grouting in the zone of the cross connection tunnels due to extremely variable and weak ground conditions, and· excavation methodologies and proposed support types of the riser to tunnel cross connections.The design process consisted of developing concepts, detailed risk assessment, three-dimensional (3D) finite element modelling and structural analysis for temporary support of tunnel lining; functional design of the ground improvement grouting and the temporary support; and permanent lining design of tunnel to ocean riser connections in a mixed soft ground/hard rock environment.The paper also presents conclusions of the design based on construction data available, and highlights the close collaboration between the design team and construction team.

Mar 8, 2011

By A Bagis, T Baker

In 1983 the New South Wales (NSW) Government began to construct a 35 km freight rail line to provide additional rail capacity to Port Kembla in the Illawarra region, south of Sydney, through a direct connection between the Unanderra to Moss Vale line at Dombarton to the Main South rail line at Maldon in the Southern Highlands. The project area lies within the carefully managed Sydney Water catchment and is also underlain by previous coal mining activities.Construction of the line halted in 1988 prior to its completion after the NSW Government reassessed the demand case and found that the project was not as viable as originally forecast. However, by this stage the line was partially constructed, including the majority of civil earthworks, approach structures to the main river crossings and establishing the portals for the Avon tunnel as a precursor to major tunnelling works.In 2012, the Commonwealth Government funded Transport for NSW to undertake the necessary engineering and environmental preconstruction works. Most importantly here, the 1980s rail link was predicated upon the use of electrically powered locomotives, whereas the locomotive fleet in operation today in NSW is diesel powered. This fact has a significant impact upon the approach and development of the Avon tunnel section, as the diesel powered locomotives combined with the length and grade of the tunnel alignment produces a unique set of conditions requiring specialist engineering design and systems to ensure safe and functional operation of the railway through the tunnel section.Given the above, the Avon tunnel will need to be supported by a ventilation and smoke control design based on the heat rejection from the locomotive consist, consideration of ambient air quality compliance, comparison against in-tunnel air quality goals, and providing safety systems in line with the fire and life safety strategy it requires.This paper explores the current development of both the tunnel civil works responding to the geography, geology, rail functional requirements, as well as the tunnel ventilation systems being revised to suit the diesel locomotives.Further, this paper describes the importance of combining the design outcomes with the procurement methodology in order to achieve the project objectives, a functional outcome and value for money across the project life.CITATION:Baker, T and Bagis, A, 2014. Maldon to Dombarton Rail Link – design development of the Avon Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J C. Small

Time-dependent deformation occurs when geo-materials are under an applied load; this may lead to additional deflection of a tunnel structure and the stress redistribution in the surrounding rock, shotcrete lining and rock bolt support system over time. A better understanding of this creep behaviour can improve the reliability of design, construction and maintenance of tunnels. Hence, the present investigation was carried out on the time-dependent properties of rock, shotcrete and the combined tunnel support system. Tunnels constructed in different ground conditions were modelled. The closure changes of the tunnel with time and the redistribution of stress in the surrounding rock, shotcrete lining and rock bolts due to the creep deformation were analysed. Results of the present analysis were compared with the results from the commercial program ABAQUS.

Jan 1, 2008

By M D. Boscardin, P A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County involves TBM tunnelling twin light rail tunnels through cohesive soils and rock under the Allegheny River and a narrow city street. Along the tunnel alignment are a listed historic building on shallow foundations as well as modern buildings on deep foundations; one major office block was actually constructed directly over the alignment during the latter phases of design process. This paper provides an overview of the general site conditions, tunnel design and the technical basis for excavation support and tunnelling decisions. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed. Project construction has now commenced and a brief summary of progress to date is included in this paper; this will be updated for the presentation to be made in Melbourne.

Jan 1, 2008

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

This is a brief introduction of a sewer pipeline constructed with a pipe jacking method in combination with a 1 200 mm finished inner diameter tunnel boring machine developed for the first time in Japan. The pipeline is located under a national highway running through a densely built urban area and is 185.7 m long and 2.9 m to 3.7 m deep from the ground surface. The geological features along the pipeline show mostly slate and partly silt. The pipeline was constructed with a newly developed multi-application type tunnel boring machine equiped with a fluid transport system. The construction consisted of tunneling by a tunnel boring machine followed by pipe jacking operations. The excavated materials were dis- charged off the tunnel by a fluid transport System.

Jan 1, 1987

By Baczynski NR, Fagan MJ

A 3050m long section of a 1.65m internal diameter tunnel is presently under construction in the Brisbane area by means of the pipe-jacking method. The soils along the alignment had been deposited in a deltaic/estaurine environment and rapid changes in soil type occur. The tunnel passes beneath several extensive bodies of surface water. Groundwater problems have been experienced with tunnelling through alluvial sands and gravels. Details of the ground conditions, the pipe-jacking method used and tunnelling experience are discussed in this Paper.

Jan 1, 1987

Subsurface development requires some geotechnical conditions and challenges. Most of then are related to the compatibility between tunnelling system and surrounded ground conditions, and design criteria. Design criteria usually involve lining pressure and ground control of displacements. In order to fulfil these requirements, geotechnical parameters have to be obtained as well as construction aspects have to be taken into account for predicting the tunnel behaviour. The Brasilia Metro is presented as a case history illustrating the geotechnical conditions and challenges for its implementation. It is 42 km long, including tunnels excavated in collapsible porous soils by the New Austrian Tunnelling Method. The Brasilia porous clay presents some characteristics, which may lead to large deformations due to structural collapse. Empirical methods were calibrated for collapsible porous soils and then applied to predict tunnelling-induced settlements. Settlements due to soil structural collapse modify completely the expected settlement profile, increasing their values from the tunnel crown to the ground surface. Consequently, surface settlement trough volumes were also greater than the ground losses around the tunnel. In this case history, structural collapse of porous soils played an important role and must have been taken into account to predict correctly the settlement trough and profile. Numerical simulation has shown that settlement magnitudes due to structural collapse are strongly dependent on the soil stiffness reduction after collapse and the extent of the collapsible zone.

Jan 1, 1999

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011