Search Documents

By Maria I. De Rosa

The U.S. Department of Energy Pittsburgh Research Center2 conducted experiments with mine conveyor belt samples in a 20-L furnace and in a laboratory fire tunnel to measure and compare the major toxic gas concentrations evolved during the combustion of the materials. The toxic gas concentrations, measured simultaneously through a multiport sampling device and treated as yield values, included hydrogen chloride (HO), hydrogen cyanide (HeN), oxides of nitrogen (NO, treated as NO), and carbon monoxide (CO). The data obtained from the two experimental systems were in good agreement. Correlations were developed for the toxic gas yields as a function of the percentage of chlorine (for HO gas), nitrogen (for HCN and NO, gases), and carbon (for CO gas) contained in the original materials. The toxic gas yields were also used to calculate a toxicity index (TI) parameter to assess the potential gas toxicity of belt materials during a fire. Furthermore, the TI and the mass loss burning rate values were used to calculate a toxicity hazard (TH) parameter to estimate the toxic gas hazard produced by a burning belt in a ventilated system. Results show that polyvinyl chloride (PVC) belts released higher HC1 concentrations because of the higher chlorine content; styrene-butadiene rubber (SBR) belts released higher CO, HCN, and NOz concentrations because of the higher carbon and nitrogen contents. The TI's, however, were greater for the PVC belts due primarily to the higher levels of HC1 produced. The fire tunnel data indicate that the SBR belts can bum with higher mass loss rates than the PVC belts, resulting in a potentially higher toxic hazard (higher TH values) even though their TI values were lower than those of the PVC belts.

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

This dictionary is published by the Bureau of Mines as a contribution to the mining and mineral literature in the belief that it will fill a recognized need. Several attempts have been made over the years to revise Albert Fay's Glossary of the Mining and Mineral Industry which first appeared in December of 1918. Frank L. Hess of the Bureau of Mines worked on a revision, but his untimely death prevented its completion. Subsequently, the writer was employed to compile and edit this dictionary in cooperation with the technical staff of the Bureau of Mines. Fay's glossary contained about 18,000 terms with 27,000 definitions; the present compilation contains about 55,000 terms with approximately 150,000 definitions. These terms are of both a technical and local nature, and they apply to metal mining, coal mining, quarrying, geology, metallurgy, ceramics and clays, glassmaking, minerals and mineralogy, and general terminology. Petroleum, natural gas, and legal mining terminology, unless of a general nature, has been excluded, as has been foreign terminology where there is an English equivalent. Several thousand Spanish-American mining terms that appeared in Fay's compilation have been removed to make way for the thousands of new English terms that have evolved over the years. Those Spanish-American and Mexican terms still used in the Southwestern United States have been retained.

Jan 1, 1968

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By Albert E. Long

THIS GLOSSARY is published lay the Bureau of Mines as a contribution too the mining literature to fill a long-felt need for a compilation of the terms used by the diamond-drilling industry. The first step toward preparation of the glossary was taken in October 1955 when the Diamond Core Drill Manufacturers Association (DCDMA) proposed that the Bureau of Mines undertake the cons compilation and publication of a glossary of the terms used by the diamond-drilling industry. The work was authorized in July 1956, and a preliminary draft of the glossary was completed in may 1958. Copies of the draft were submitted for review to members of the DCDMA and appropriate personnel of the Bureau of Mines. The final draft, incorporating the many helpful suggestions of the reviewers representing both the diamond-drilling industry and the Bureau of Mines, was completed in March 1959.

Jan 1, 1960

By Albert H. Fay

This glossary is published by the Bureau of Mines as a contribution to the mining literature in the belief that it will fill a long-felt need. It contains about 20,000 terms; these include both technical and purely local terms related to metal mining, coal mining., quarrying, petroleum, and natural gas, and metallurgical works; names of useful, important, and common minerals and rocks; and geological terms. It presents in one comprehensive volume the available standard, technical terms relating to the mining and mineral industry, as well as provincialisms that have been or are now in use in English-speaking countries. The glossary also includes many terms relating to ceramics and. the clay industry, glass making, foundry practice, railway and building construction, electrical installation and power-plant equipment, and chemical terms relating to metallurgical practice. Complete lists of terms for each of these allied industries are beyond the scope of this glossary. Paleontological terms, although closely associated with geology, are far removed from mining and metallurgical operations, and for this reason have been omitted.

Jan 1, 1920

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By D. G. Leddy, J. B. Johnson, L. D. Gratz, S. T. Bagley

"Studies have been conducted at Michigan Technological University (MTU) for over twenty years on methods for characterizing and controlling particulate emissions from heavy-duty diesel engines and die resulting effects on regulated and unregulated emissions. During that time, control technologies have developed in response to more stringent EPA standards for diesel emissions. This paper is a review of: 1) modem emission control technologies, 2) emissions sampling and chemical, physical and biological characterization methods and 3) summary results from recent studies conducted al MTU on heavy-duty diesel engines with a trap and an oxidation catalytic converter (OCC) operated on three different fuels. Control technology developments discussed are particulate traps, catalysts, advances in engine design, the application of exhaust gas recirculation (EGR) and modifications of fuel formulations. Methods for dilution tunnel sampling, particle size analysis, chemical analysis with emphasis on polynuclear aromatic hydrocarbons (PAH) and nitro-PAH, and biological characterization using mutagenic activity (Ames) assays are described, along with statistical approaches to experimental design and data analysis.In studies at MTU, both particulate traps and an OCC have been shown to be effective for the reduction of total particulate mauer (TPM), with the OCC being better al reducing all forms of hydrocarbon emissions, including PAH and nitro-PAH, and with the traps being better at removing the solids (SOL). The use of low sulfur fuel (0.Ql % by mass) has led to additional reductions in TPM; the low sulfur fuel has been shown to reduce the number of small, nuclei-mode particles for one of the engines tested. PAH, nitro-PAH, and mutagenic actively levels generally decreased with use of either the traps or the OCC.INTRODUCTIONDuring the 1980s and the early 1990s there have been significant advancements in the development of technology to control diesel particulate emissions. Efforts have been focused on internal control of the engine by design, the use of after-treatment devices, and improvements in fuel formulations to reduce all the diesel emissions. The research and development activities have been driven by the need to meet the US EPA heavy-duty vehicle standards shown in Table 1. The important standards for new technology are the 1994 heavy-duty vehicle 0.1 gm/bhp-hr particulate, the new urban bus 0.05 gm/bhp-hr particulate standard for 1996 and the heavy-duty vehicle 4.0 gm/bhp-hr NOx standard for 1998."

Dec 1, 1995

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

By Gordon T. Austin

The combined value of production of natural abrasives, which includes tripoli, special silica stone, garnet, staurolite, and emery, increased about 21070 in 1989. The increase in the value of staurolite and tripoli production was the result of an increase in the quantity of materials produced and an increase in the unit value. Emery decreased due to the significant decline in the volume of the material produced. Special silica stone experienced both a decrease in unit value and quantity produced. Garnet showed a small increase in quantity, but a decrease in unit value. The silicon carbide industry saw a slight decrease in the quantity produced and a 12070 increase in the value of production. The fused aluminum oxide industry showed a 5070 decline in the quantity produced, but enjoyed a 15070 increase in the value of production. Combined production for both industries decreased 4070 in quantity but increased 13070 in value compared with those of 1988.

Jan 1, 1991

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased in 1993. The increase in the value of tripoli production was the result of an increase in total production. Special silica stone experienced an increase in unit value but decrease in the quantity produced. Garnet showed a 19 % decrease in quantity and an 8 % decrease in value. Staurolite increased about 51 % in the quantity produced and 136 % in value compared with those of 1992. Staurolite's significant increase in value of production resulted from a 56 % increase in the unit value. The fused aluminum oxide industry showed an 8 % decrease in the quantity produced and a 13 % decrease in the value of production. The silicon carbide industry saw an 11 % decrease in the quantity produced and an 8 % decrease in the value of production. Combined, the industries decreased 9 % in quantity and 11 % in value compared with those of 1992.

Jan 1, 1993

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, staurolite, and emery, increased in 1987. The increase was, in certain cases, because the materials were used in nonabrasive applications, such as the increased use of tripoli as a filler and special silica stone material as a special-purpose crushed stone. The increased use of garnet as a blasting media accounts for most of its growth. Production and sales of garnet were at a record-high level in 1987. [ ]

Jan 1, 1989

By Robert G. Clarke

The production of natural abrasives varied in quantity and value compared with those of 1974. Output of tripoli-type materials and garnet both decreased in quantity and value. Special silica stone products decreased in quantity but in-creased in value. The production of emery increased 38% in quantity. The production of manufactured abrasive materials decreased for all types and the decreases were more in quantity than in value. [ ] FOREIGN TRADE Imports of abrasive materials were 15% less in value than in 1974, and exports plus reexports decreased in value 10%. Net exports, the excess of exports and reexports over imports, were $9.3 million, about four times that of 1974. The volume of all abrasive materials exported decreased and the value of nearly all decreased.

Jan 1, 1977

By W. T. Adams

The production of natural abrasives var¬ied in quantity and value compared with 1975. Output of tripoli-type materials and garnet increased in both quantity and value; special silica stone products decreased in quantity and increased in value; the production of emery decreased. The production and value of manufactured abrasive materials increased for all types. [ ]

Jan 1, 1978

By Gordon T. Austin

The combined value of production of natural abrasives, which includes tripoli, special silica stone, garnet, staurolite, and emery, increased about 9% in 1988. In the case of emery, the increase was due to an increase in unit value of the material produced. The increase in the value of garnet and staurolite production was simply the result of an increase in the quantity of materials produced. However, special silica stone experienced both an increase in unit value and quantity produced. The nonmetallic manufactured abrasives industry, which includes only silicon carbide and fused aluminum oxide in the reported statistics, enjoyed the best production year since 1981 in terms of total quantity produced. Production increased 22% in quantity and 16% in value com-pared with those of 1987.

Jan 1, 1990

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The increase in the value of tripoli production was the result of an increase in the unit value. Emery increased owing to an in? crease in the volume of the material produced and an increase in the unit value. Special silica stone experienced a decrease in unit value and an increase in the quantity produced. Garnet showed a 10% in? crease in quantity and a 73% increase in unit value. Staurolite decreased about 8% in the quantity produced, and the value of production decreased about 10%. The fused aluminum oxide industry showed a 5% decline in the quantity produced and in the value of production. The silicon carbide industry saw a 10% decrease in the quantity produced and a 9% decrease in the value of production. Production for both industries decreased 7% in quantity and value compared with those of 1989.

Jan 1, 1993

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars on accident prevention in metal and nonmetallic mines. These circulars are: 1. Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957