Search Documents

By FHATUWANI SENGANI

The understanding of yielding pillar behavior has been well documented in terms of pillar strength using numerical simulations and empirical formulas, but the understanding of how fracture propagates in a matured yielding pillar is not well established. A new empirical summation chart of fracture distribution along the matured yielding pillar is presented in this paper. The chart was developed using ground penetrating radar (GPR) supported by borescope observations, focusing on monitoring the distribution of extension fracture.

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By Mahmut Yavuz

to in Old Uighur Turkish as Tolay kopugu, in Ottoman Turkish as Derya kopugu, and in modern Turkish as Luletasi. Scientifically known as sepiolite, it is represented by the formula Si12Mg8O30(OH)4(H2O)4(8H2O). Sepiolite is a natural clay mineral composed of hydrous magnesium silicate, characterized by a structure of alternating blocks and tunnels that develop in the direction of the fiber. Each structural block contains two silica tetrahedral sheets surrounding a central layer of magnesium oxide- hydroxide. Sepiolite exists in two distinct forms in nature: alpha-sepiolite and beta-sepiolite. Alpha- sepiolite is amorphous, compact, and resembles pellets that look like sea froth, hence its Turkish name Luletasi. In contrast, beta-sepiolite appears as amorphous aggregates or small, flat, round particles. These two forms exhibit different physical properties. Meerschaum was also studied by Brauner and Preisinger in 1958, who agreed that it primarily consists of sepiolite (2MgO·3SiO2·nH2O). According to these researchers, water is present in its mineral, zeolitic, crystal, and structural forms. Meerschaum is commonly used for adsorbing various liquids, as an ion exchanger, and for dispersing and insulating paraffin in the chemical industry (Gokdemir and Dogan, 2011). Sepiolite deposits of the meerschaum type are primarily found in Turkey, Somalia, Tanzania, Kenya, and Mexico. Alongside high-quality, low-density, and highly porous meerschaum, Somalia also has sedimentary sepiolite formations. The total reserves of these deposits are estimated at around 50–100 million tons (Sariiz and Isik, 1995). Meerschaum, also known as “white gold” or “sepiolite,” is a unique mineral highly prized for its lightness, heat- resistant properties, and ability to be carved into intricate designs. Found predominantly in Eskisehir, Turkiye, meerschaum mining and processing have become significant contributors to the local economy and cultural heritage. This paper explores the history, economic importance, mining practices, and environmental impacts of meerschaum mining in Eskisehir and discusses the challenges and opportunities faced by the industry.

Feb 1, 2025

By Robert C. Bacon

The first commercial installation of the Dashaveyor has recently been completed at the White Pine Mine in Northern Michigan. After four years of development work, including prototype testing, and pilot plant operation, this new and unique system is being tested under operational conditions. Many of you may be familiar with the concept through numerous articles which have appeared in the technical press. But this discussion of the system will be simplified and less time consuming with the presentation of a portion of a film showing the Dashaveyor in actual operation. After the movie, I will show some slides which will supplement and clarify it and hopefully lay the basis for questions you will undoubtedly wish to ask.

Jan 1, 1968

By Valerie (Wollet) Rebar

Successful execution of fast-track projects is an arduous task at best. Effective and organized management, a comprehensive technical design with an independent check-and-balance system, and optimal schedule components all play major roles in project success, regardless of the required timeline. However, a fast-track schedule intensifies the significance of each of these elements due to the heightened time constraints.

Jan 1, 2008

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By Michael Casson

With the mining industry changing rapidly due to mergers, acquisitions and fluctuating market pricing, today?s market for coal, minerals, ores and aggregates demands electrical apparatus that perform every time with maximum efficiency and with consideration for personnel safety. This is especially true in existing mining operations where every payload counts. Draglines are the workhorses of surface mining operations, and reliable and efficient operation is absolutely critical to success. However, the inherent disadvantages of using dc motors and motor-generator (MG) sets can significantly impact productivity and return on investment (ROI).

Jan 1, 2013

By Harrison H. Roberts

A. We are aware that many who are in the audience have perhaps heard before some of the material which will be presented. Since our firm is more closely associated with the heavy construction industry our experience is more oriented in that direction. Notwithstanding this, the subject your program committee has asked us to present centers mainly in the earth-moving field. We find a common denominator between say, the stripping of a site to uncover an ore-body which will be developed by open-pit methods, and that of excavating & transporting materials for an embankment dam, airport or other project. Both are earth-moving problems and we offer for your consideration a means of determining the most favorable method, equipment selection and resultant cost. We do considerable studies involving rock excavation for tunnels, underground powerhouses, inclined and vertical shafts for penstocks, muck-removal, electrical cable & other related underground work. Hence, we believe we speak the same language.

Jan 1, 1972

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By Gary N. Greenfield

This morning, gentlemen, I should like to discuss resin anchors of a type introduced to North America approximately 2-1/2 years ago. We shall also briefly review the basics of mechanically anchored rockbolts so that a general comparison may be made. Previous efforts with synthetic resins were aimed at aiding a mechanical Or "point" anchor, obtain a better purchase in the rock mass. Resin cartridges of the type to be described in this paper are capable of achieving point anchorage or full encapsulation of mine roof or rockbolts. Of significance, therefore, is that unlike a mechanical bolt, placed and tensioned, celtite rockbolts may be fully grouted and tensioned or left untensioned in the installation sequence. Our principle effort has been to offer this system to mining and civil engineers who have encountered difficult rock conditions and wish to reinforce strata to achieve a greater degree of permanence and safety.

Jan 1, 1972

By Firat Atalay

Estimating the spatial distribution of ore grade is one of the most critical steps to proceed with an investment decision on a deposit. Kriging is the most widely used method to estimate the ore grade, but alternative techniques are being developed. Machine learning algorithms can be used as alternative methods to classical kriging. In this paper, the iron (Fe) grade of a deposit is estimated with the XGBoost algorithm, and the results are compared with kriging estimation results. For the estimations, samples collected from drillholes were used. Due to the different natures of the estimation methods, different steps were taken to perform the estimations. The results show that XGBoost produced higher-range estimates, which is a desired result in ore grade estimation, and the minimum and maximum of the estimates were lower and higher than the kriging estimates, respectively. However, like kriging, the estimation results were smoother than composites, and the variance of the XGBoost estimates was lower than the variance of composites. This means that even though estimation with XGBoost mitigates the smoothing effect, the estimation results suffer from smoothing like kriging.

Dec 1, 2024

By James C. Fowler

The use of ground-probing radar as a reflection mapping tool has expanded greatly in the last few years. This tool can now be used to produce near surface information which is very useful to geotechnical engineers. Using the lightweight field equipment now available, it is possible to use the radar within mines and tunnels to obtain information which may impact the safety and production of these operations.

Jan 1, 1979

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By Tadashi Nishida

Subsidence due to mining caused various kinds of damage to the surface structures, and actually great deal of mining damage becomes the severe social problem at some time in many coal fields, but the most of mining damage was restored at present. Recently, the effect of old coal working on the deformation of newly constructed structures has become into question, because it was obliged to plan many engineering structures in old mining areas for the shortage of adequate construction sites and the difficulty of getting location. That is, building, dams, bridges for railroads and highway, power plants, tunnels, storage tanks and so, have to be built on the ground which has old coal working.

Jan 1, 1982

By J. Weyer

"Colored gemstones are most often mined in small scale artisanal mining operations. Sri Lanka is well known as source for precious stones since thousands of years. Gemstones are mine in small open pits, directly in rivers (river dredging) and in underground mines. Almost all mined deposits are alluvial deposits. PRECIOUS STONES AND DEPOSITS Precious stones from Sri Lanka are well known for thousands of years. Tales and legends from Arabia, India, China and reports from discoverers like Marco Polo describe the fabulous stones from Ceylon which was the name for Sri Lanka before 1972. Already 1000 BC King Salomon got valuable gemstones from the legendary Queen of Sheba on her visit to Jerusalem. Paintings (frescoes) of the “cloud maidens” with huge gemstones can be seen at the “mirror walls” of the Sigiriya rock fortress - one of the eight World Heritages Sites of Sri Lanka.And even today some of the most valuable and most desired gemstones come from Sri Lanka. The term “Ceylon Sapphire” stands for an excellent royal blue color of high quality corundum from Sri Lanka. Reason enough to look a bit closer how these gemstones are mined. Sri Lanka has rich gemstone deposits which are mined underground, in small open pits or directly within a river. Some of the primary deposits in magmatic and metamorphic rock are also known, but most gemstones are mined in secondary alluvial deposits. Gem bearing deposits can be found in a band from NW to SE. Highly probable deposits and main mining areas can be found around Ratnapura – the city of gems, down to the coast (Matale) and up to the region around Elahera. These secondary deposits are mostly thin layers of gravel and sand, so called “illam”. The depth can vary between some dm to 10 25 m or even almost 40 m. But the average depth is about 12 m. Gemstone mining is controlled, licensed and regulated by a special authority – the National Gem and Jewelry Authority - which was founded in 1993. Another task of this authority is the promotion and development of the gemstone industry and the control of import and export of gemstones. Any violence of the NGJA law can lead to a fine or even up to 5 years imprisonment. To increase the confidence in the gemstone industry the Authority offers a unique service to foreigners. All bought gemstones can be tested free of charge in certain laboratories in Ratnapura and Colombo. So visitors can be sure they got no imitations, wrong stones or even synthetic stones or glass. It was said that detected synthetic stones will be destroyed and the seller will do all he can to replace the stone with the right stone. Otherwise he will lose his license."

Jan 1, 2016

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized using waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empirical testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicate that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate than conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965