Search Documents

By Neil J. Duncan, Edward R. Langfield

A hydraulic rock breaker was developed in Germany by Helmut Darda and uses a wedge-plug and feathers mechanism powered by a 10,000 p.s.i. power pack. During the past four years these tools have been increasingly used all over North America for secondary breaking of boulders and rock. More recently, techniques have been developed to break rock off the solid in trenches and rock emplacements where blasting is pro¬hibited or very limited. Underground operations are commencing to adopt the splitter for scaling plus including systems which can be efficiently applied to chambers and mines. Mr. Neil Duncan, who was originally scheduled to give the main part of this presentation has, during this past month accepted a position with the Alberta Energy Resources Conservation Board in Calgary. The board encourages its members to take part in seminars such as this but, unfortunately, due to the heavy pressure of work, it was impossible for him to attend this conference. Mr. Duncan has, however, forwarded me his notes and suggest¬ions, and using these, combined with a slide presentation, we feel that we can quickly and clearly define the operations and application of the hydraulic splitting technique as it applies to your profession and tunnelling work. The first question that most of you are asking is, "Why use a hydraulic splitter if you can blast?" Our answer to this is that we are not advocating the use of hydraulic splitting where blasting is feasible - but, during the past decade many applica¬tions have arisen where blasting is not allowed, or restricted

Jan 1, 1997

By D. C. Willett

INTRODUCTION The Symposium on the Development of Underground Space, held in Seattle, Washington, from October 1 through 3, 1980, was organized by the "Deep Space" subcommittee of the ASCE's Underground Research Technology Council. The primary objective of the symposium was the exploration of the interfaces between the investigation, design and construction of large underground facilities in "deep space" which, for the purposes of the committee, has been defined as starting at 100m below ground surface. The meeting focussed primarily on tunnels, caverns and shafts in hard rock; the meeting format comprised a number of brief presentations concerned with the technical aspects of investigation, design and construction, followed by an open discussion, and concluded with the assembly of recommendations regarding the interface problem by the symposium participants. The principal considerations brought out during the symposium, and a general review of the conclusions, are briefly presented in the following paragraphs. INVESTIGATION The sessions dealing with "Investigation" were chaired by Dr. H. Pratt. Presentations were made by Dr. D.C. Banks, Dr. W.A. Hustrulid and Dr. Pratt. The extent of the interface of the investigation phase with the other (design and construction) phases of an underground facility will depend in large measure upon the nature of the facility; at one end of the spectrum, the investigation must be in continuous and closely coupled relationship with the design of a radwaste facility. At the other end of the spectrum, for (say) a small mining operation, the interface is largely associated with the initial development, with only minor on-going involvement.

Jan 1, 1981

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By Chapman Young, Donald E. McCarthy

Many hard rock tunneling projects, where the majority of excavation can be accomplished with TBMs, will still require considerable specialized excavation which can not be done with a TBM. This secondary excavation, involving cross cuts, galleries, flattening of the invert, increases in bore diameter, et cetera, may be accomplished with conventional drill and blast, applied on a small scale and usually with fracture control techniques, or with mechanical splitters. The problems of using explosives in many of these cases and the high cost of mechanical splitting excavation make the consideration of other approaches attractive. The PCF rock excavation method, which has recently been reduced to commercial practice for mine-development excavation, offers an attractive alternative to drill and blast and mechanical splitters. With the PCF method the rock is excavated utilizing a small-charge, propellant-driven, controlled, penetrating-cone fracture process. Excavation is carried out continuously by combining the PCF hardware with integrated mucking capabilities on a carrier which remains at the excavation point. In addition to the benefit of providing for complicated excavation geometry, the PCF method also causes minimal damage to the remaining rock which will significantly reduce ground support requirements. In very bad ground, the continuous nature of PCF excavation allows ground support to be applied as limited sections are exposed thus reducing both the duration and extent that the ground would be free to move. Data on PCF excavation parameters, as measured in actual mining operations, indicate that crosscuts, galleries and the like could be excavated at considerable cost savings compared to drill and blast or mechanical splitters.

Jan 1, 1995

By Steven H. Brown

Ore bodies which were once uneconomical to mine by conventional methods such as tunneling or open pits, have become attractive due to the development of nonconventional techniques, involving considerably less capital expenditure. Technologies such as uranium solution mining or in-situ leaching, have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall U.S. uranium supplies during the next 20 years. Commercial size solution mining production facilities have operated since late 1975. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange, precipitation, calcining, and packaging operations. This paper presents an overview of the solution mining process and the health physics monitoring programs developed over the last four years at several production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. Some special monitoring considerations are presented which are required due to the manner in which radon gas is evolved in the process and the unique aspects of controlling solution flow patterns underground. An overview of the major aspects of the health physics compliance and monitoring programs that have been developed are discussed.

Jan 1, 1981

By J. Köppel, K. Kovári, Ch. Amstad

INTRODUCTION The measurement of displacements in soil or rock in the vicinity of underground openings provide valuable information for a better understanding of the behaviour of the structure. On the basis of systematic observations conclusions can be drawn concerning - safety of the opening in the various stages of excavation - effectiveness of the support measures - nature of the rock pressure to be expected - influence of the construction of the opening on neighbouring structures (settlements of foundations, underpassing other tunnels etc.) - comparison of theoretical predictions with the actual structural behaviour (1). Today there are several types of suitable instruments available that can be employed at reasonable costs for such investigations (2). The most important ones are the multiple point borehole extensometer, the inclinometer and the multiple point borehole deflectometer. As is well-known, the extensometer only measures the displacement component in the borehole axis, while the inclinometer and the deflectometer provide monitoring of rock mass movements normal to the borehole axis. In the following a new instrument is described, which has been given the name Extenso-Deflectometer ISETH. In this single piece of equipment certain features of the above-mentioned three types of borehole instruments are incorporated. it enables the measurement of all three components of the displacement vector at consecutive points along the borehole, the axis of which may have any direction in space. This device is portable like the inclinometer. A simplified version

Jan 1, 1979

By L. L. Gagné

The Churchill Falls Development will eventually be the largest source of hydroelectric power in North America. Churchill Falls was discovered in 1839, but until recent years it was not practical to begin development of this site to tap the 7 million horsepower available. This $1 billion project is located in Labrador, 700 miles northeast of Montreal and 650 miles northwest of St. Johns, Nfld. The construction will divert the Churchill River 5 miles upstream from the 245 foot Churchill Falls. Rapids above and below the Falls, together with the Falls proper, give a natural head of 1,040 feet. In contrast to the basic simplicity of the surface installations, the powerhouse labyrinth is astounding in size and complexity. The largest in the world, it consists of three major chambers - the powerhouse, 972 feet long by 81 feet wide and 154 feet high; the surge chamber, 763 feet long, 40 feet to 64 feet wide and 148 feet high; and the transformer gallery, 856 feet long by 50 feet wide and 39 feet high. Other major features include eleven inclined penstocks, each 1200 feet long and 20 feet in finished diameter; eleven draft tubes averaging 37 feet in finished diameter and 162 feet long; six vertical cable shafts each an average of 865 feet in length; a series of eleven short bus tunnels linking the powerhouse and the transformer gallery; a vertical power-

Jan 1, 1997

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

By William G. Doepken

After 15 years of production, 91 Mt (100 million st) of ore mined and nearly 227 kt (500 million lb) of molybdenum produced, Climax Molybdenum Co.'s Henderson Mine and Mill are being modernized as a new mining level is brought on line. The $40 million investment in mine development and plant modernization positions the Henderson complex as one of the largest, low-cost primary molybdenum producers for the next 15 years. Henderson history The Henderson Mine and Mill facilities are located on the east and west flanks of the Continental Divide about 80 km (50 miles) west of Denver, CO. The underground mine and surface mill sites are linked by 16 km (10 mile) of railroad tunnel and 8 km (5 mile) of surface trackage. The mine, railroad and mill were built between 1968 and 1976 at a cost of $500 million. Each has operated at various levels of production over the past 15 years. The Henderson Mine was originally developed using a highly mechanized, panel caving mining system. Over the past 10 years, mining methods, equipment and railroad operations have been improved to position Henderson as one of the most productive and lowest cost underground mining operations. At the same time, the mill and concentrator facilities were upgraded to reduce costs and improve product quality. During this time, manpower was reduced from 2000 to 560 employees. These 560 people increased productivity to 54 t (60 st) per total manshift. They reduced operating costs by 50%. And they dramatically improved safety performance. However, as the 1990s approached, the modernization of the Henderson mining and milling complex and the development of the new 7700 mining level became the primary goals to guide Henderson into the 21st century.

Jan 1, 1991

By Sol Ribakoff

In 1973, the Subcommittee on Contracting Practices, U. S. National Committee on Tunneling Technology, National Academy of Sciences, under the able chairmanship of A. A. Mathews, Engineering Consultant, now residing at Kaunakokai, Hawaii, undertook the task of developing recommendations for improving the performance of underground construction work, reducing the costs of such work and minimizing the adverse atmosphere in which owners and contractors were performing their respective functions. The author of this paper and C. F. Palmetier, a highly qualified engineer, were thereupon appointed as staff assistants to the Subcommittee, to conduct a study of existing practices and relationships in Western Europe and in the United States, to formulate recommendations, for consideration by the Subcommittee and the participants in a future workshop, as to desirable improvements in United States contracting practices and relationships. The study, conducted during 1973 and 1974, involved personal interviews of a total of 162 owners, engineers, contractors, lawyers, and educators throughout the United States and in 7 European countries, the analysis of 178 replies to questionnaires sent to individuals and firms involved directly or indirectly in construction, and a workshop, near Napa, California, attended by 53 representatives of all segments of the construction community. The resulting report, entitled "Better Contracting for Underground Construction", was submitted by the Subcommittee to the National Academy of Sciences, which approved its publication in 1974 by the National Technical Information Service. It may be obtained from that Service at Springfield, Virginia, 22161, as Accession No. PB-236 973. It was recognized-during the course of the study that while contracting practices and owner-contractor relationships were the

Jan 1, 1981

By Paul C. Jones

Summitville is an old mining district located south of Wolf Creek Pass in the southern San Juan Mountains of Colorado at an elevation higher than 3500 m (11,500 ft). The Summitville mine site is about 40 km (25 miles) southwest of Del Norte. The current mine, developed by Galactic Resources Ltd. and its subsidiaries in the mid-1980s, is on the north facing side of South Mountain. The area is drained by Cropsy Creek to the east and Wightman Fork to the north, both tributaries to the Alamosa River. Mining in the Summitville area began in 1870 when James Wightman discovered placer gold on what is now known as Wightman Fork of the Alamosa River. The first vein-type deposits were located in 1873 on South Mountain near the current Summitville Mine. Mining began in the district in 1875 and continued sporadically through 1942. Major mining episodes occurred from 1875 to 1894 and from 1926 to 1942. Total gold production from the mining district through 1949 totaled 7.5 t (240,000 oz). An additional 7.7 t (249,000 oz) were produced during Galactic's tenure. Natural degradation of the outcropping sulfide-rich veins in the area and the early mining activity, including development of the Reynolds, Dexter and Iowa drainage tunnels in the late 1890s, have polluted the streams draining the area with heavy metals and acidic water. Names of the various tributaries to Wightman Fork, such as Iron, Alum and Bitter Creek, testify to this natural pollution. This degradation has reduced, or killed, aquatic life in several area creeks, including Wightman Fork, for many years before recent mining activity.

Jan 1, 1993

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Ian M. Loomis, Malcolm J. McPherson

A fuel-rich fire exists when the quantity of fuel exceeds the oxygen available to support complete combustion. The transition of a mine fire from Oxygen- rich to Fuel-rich combustion, at this time, represents a point-of-no-return in the fire fighting efforts. Once the transition has been made to fuel-rich the fire can spread at a rate 6 to 10 times as fast as in the oxygen-rich state. Utilizing available technology the fire fighters are left to seal the fuel-rich fie as the only technique to extinguish it. In order to minimize the devastating effects of a fuel- rich fire it is important to understand the means by which the fire becomes fuel-rich and by what means the fire may be returned to an oxygen-rich state. This paper covers: the development mechanism of a fuel- rich fire in a coal mine entry and the physical and chemical effects of applying water to a fire. Experiments concerning these matters have been conducted in a 30 cm square wind tunnel constructed at the Virginia Polytechnic Institute and State University as a model coal mine entry. This paper also addresses the results obtained in testing application of a water mist to fuel-rich fires in this model. These tests have centered on the development profile of a fuel-rich fire in a duct and demonstrate a means of regaining control of a fuel-rich fire by returning it to an oxygen-rich state.

Jan 1, 1995

By Richard L. Daley

Today's subject of discussion, "OSHA AND ITS PROBLEMS", must be covered in the time allotted with a slight tongue in cheek approach, for if one is to believe that the "problems of OSHA" can be covered in a twenty minute review, he, himself, has one of three problems: 1. He has residual combat fatigue left over from World War II. 2. He is an egomaniac. 3. He is afflicted with both of the above. Clearly, the difference between divinity and humanity lies in their work. All human endeavor is plagued by errors and omissions, and unless one would be so facetious as to equate bureaucracy with godliness, our government-sponsored ventures seem to receive more than their share of missive missles with which to combat the ills of our society. Coming from an industry known for its undertaking of gargantuan projects, I feel capable of looking at things from the big picture perspective. No one would deny that the massive influx of government, both in the monetary and supportive personnel roles, has accomplished much. But only we, as tunnel constructors, have moved countless mountains of muck, placed endless yards of concrete and engaged the public on numerous fronts and in spite of all, at times have even made a profit! Profit! What a dirty word in our society today. It makes one shrink back from the filthy overtones dripping with the cloying scent of decay. Never shall we judge the success of our government programs with such a slimy yardstick as profit. No, for that which has been conceived in the bowers of Camelot, the measure must be more elevating and inspiring. Something to bring a proud bearing to our efforts! Nothing has helped to alleviate the suffering of man as much as medicine. The eradication of typhoid, polio, and

Jan 1, 1979

By James J. Olson

INTRODUCTION The need for Government-sponsored research and development to increase excavation rates and lower costs for tunneling and mining operations in a variety of rock types has been emphasized in a wide range of publications from advisory panels, symposiums on rapid excavation, and individuals. In response to the predicted demands for mining and construction-oriented underground excavations for the next two decades (1970-1989), a comprehensive 10-year, $200-million research program in rapid excavation was proposed by the National Academy of Sciences in 1968 (1). Although the large program recommended by the Academy has not been funded, substantial Government-sponsored research in rapid excavation has been conducted during the past several years. This paper reviews some of the significant research accomplishments obtained under a three-year, $6.6-million research program in rock mechanics and rapid excavation sponsored by the Defense Department's Advanced Research Projects Agency (ARPA) and managed by the Bureau of Mines. In addition to the rock mechanics research, five major phases of excavation; systems analysis, geologic prediction, rock disintegration, ground support, and materials handling were represented by the projects funded under the ARPA program. The brief outline below recapitulates the major research areas and some of the projects summarized by this paper: Excavation Process Modeling by Computer Geologic Prediction Geologic Reconnaissance for Site Selection Longhole Probe Drilling for Hazard Detection

Jan 1, 1974

By Richard Newcomb

It is four years since the seminal study of demand for rapid excavation by the National Academies of Sciences (NAS) and Engineering outlined this technology's opportunities, requirements and significance to the challenges of urbanization and natural resource conservation. The demand study was quite simple. Opportunities were valued at market while requirements to produce new technologies were valued at cost. The significance of new technology in economic terms was measured by the net discounted gains to users over time. The Academy view in 1968 was that these gains, even most modestly estimated, appeared large enough to justify the bill for research proposed by that Committee (1). In 1970 the question of demands became international in what is recognized as the first international experiment in technological policy analysis, terminating in the Advisory Conference on Tunneling of the Organization for Economic Cooperation and Development (OECD)(2). A monumental demand survey formed the basis for its economic assessment. The twenty-two OECD nations also made an impressive attempt to measure the magnitude of existing research and development efforts. In their recommendations periodical statistical demand forecasting and collection of demand data (Recommendation 1) was given central importance for public planning (Recommendation 2), the financing of public construction (Recommendation 3) and the encouragement of technological advance (Recommendation 4). Their program for international cooperation led to OECD's establishment of a Directorate for Environmental Affairs, and influenced the organization of the World Environmental Conference meetings now held in Stockholm under United Nations auspices. The OECD Conference was the first example of "an attempt to apply the concept of technological policy analysis to a 'civilian' technology having potentially

Jan 1, 1997

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998