Search Documents

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By Dianne C. Marozas

The U.S. Bureau of Mines is conducting research to evaluate the potential for developing an in situ leach mining process that will selectively extract manganese from oxide ores, leaving gangue relatively undisturbed. To accomplish this, a geochemical approach, based on deposit-specific information such as mineralogy and geology, is used to constrain the operating parameters of the system. Among the studies being conducted are (1) leaching experiments to define reaction mechanisms and kinetics, (2) detailed petrologic characterization at the microscopic scale to assess Mn distribution and leaching efficiencies, (3) deposit characterization and evaluation, and (4) development of potential Mn recovery schemes. Data from these studies are being used to develop engineering design information for an in situ mining process. Specific details of the Bureau's research project are discussed, including results obtained to date.

Jan 1, 1991

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By Donald M. Podobnik

The Cuajone Concentrator of the Southern Peru Copper Corporation is located approximately 900 kilometers southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity. Since the plant was started in July, 1976, the throughput has steadily increased from 36,000 to 46,000 metric tons per day. The widely distributed molybdenite content of the ore body ranges from 0.02 to 0.04% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite.

Jan 1, 1981

By Stephen E. Kesler

Carbonaceous sedimentary rocks are abundant in the upper part of the caldera or maar that hosts the Puebio Viejo Au-Ag district, and much of the Moore sulfide zone is in these rocks. These rocks are thinly layered and contain scattered plant remains and variable amounts of volcaniclastic debris and pyrite. The carbonaceous matter in the sediments yields no X-ray diffraction pattern and is not graphite. It has C/N ratios of 4 to 10, and &13C values of about -25 per mil, which indicate that it is dominantly of marine organic origin and partly degraded. Atomic S/C ratios in the unmineralized part of the carbonaceous rocks have a median of about 1.2, much higher than most similar unmineralized rocks, reflecting not only the abundance of pyrite in the sediments, but also the fact that the organic material contains several percent sulfur. Extracts from the organic material indicate that it is thermally mature and that it reacted with the hydrothermal solutions. Atomic S/C ratios in the mineralized carbonaceous rocks are generally higher than those in unmineralized carbonaceous rocks, ranging to values of 5 and more. These differences indicate that significant amounts of carbon were consumed by the reduction of sulfate and metal chloride complexes in the mineralizing fluids as they passed through the carbonaceous sediments. Direct reaction between organic material and ferrous chloride-bearing, acid-sulfate hydrothermal solutions probably caused continuous deposition of pyrite during this period. Intermittent deposition of gold from chloride complexes by the same reaction was probably facilitated by boiling or C02 effervescence.

Jan 1, 2013

By R. W. Culbertson

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past twenty-five (25) years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated by the Glen-Gery Corporation which is located in eastern Pennsylvania; the National Lime and Stone Company which is located at Carey Ohio; and Holston Defense Corporation which is located at Kingsport, Tennessee. There are, however, numerous operating gasifiers in other parts of the world. Recent events indicate that this situation is changing. The quantity of domestic natural gas available to the interstate market has been declining at the same time that demand for all forms of energy has been increasing. The current potential market for gas with a heating value ranging from 100 to 500 Btu per cubic feet has been estimated at sixteen (16) quads (16 x 1015 Btu) per year. This is expected to grow to twenty (20) quads by the year 2000.

Jan 1, 1978

By Bryson D. Trexler

Man's activity in developing, operating, and abandoning a mine often affects the quality of the ground water and surface water. Acid water drainage from mines is an example of an impact from mining that results in degradation of ground and surface water. New flow systems are created by the mining activity. The mining made possible complex chemical reactions that, with water movement, create a discharge of low pH, poor quality water. Remedies for these problems fall into two general solutions: 1) treatment of the end product and 2) reversal of some aspect of man's disturbance of the natural system. The relative reversibility of various aspects of man's impact from mining activities ranges from relatively easy to very difficult, from economically feasible to economically infeasible, and from technically possible to essentially impossible with present knowledge. The relative reversibility of a mine-related problem cannot be assessed without first understanding the detailed physical interactions that combine to form the problem. Acid water drainage is a combination of the availability of several chemical factors with the availability of water for a transport mechanism.

Jan 1, 1982

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By Ashutosh Kumar Bharati, Rajesh Rai, B. K. Shrivastva, Arunava Ray

Opencast mining method is one of the most productive mining methods available at present, which is generally associated with the removal and handling of a huge amount of overburden material. Hence it imposes a serious challenge of dump slope stability and that too, mainly in the case of internal dumps. The study is primarily focused on the stability of dragline dumps and the subsequent development of a rating system to classify the stability of dragline dump profiles. Initially, numerical simulation is executed through RS2 (Version 9.0) software, which is based on the finite element method. Thereafter, simulation results are used to perform the sensitivity analysis of various geometrical and strength parameters of the dump slope, and the two-factor interaction method is also incorporated into the analysis, this method included the dependency of closest parameters while calculating the sensitivity index, and thereafter, it is converted into the rating of each parameter. The strength parameter like the angle of friction and the geometrical parameter like slope angle of the bench between the coal-rib roof and dragline sitting level are assigned the highest rating value. Based on the overall rating of the dragline dump, the dump slopes are classified into various classes, viz., very safe, safe, vulnerable, unstable, and highly unstable. This classification proved to be handy in the quick estimation of the stability of the dragline dump and also gives an idea of designing optimum and safe dragline dump profiles. The developed classification chart has been validated by the previous research works and has found similar results.

Feb 15, 2021

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

By Thomas Novak, Sampurna Arya, Joseph Sottile

Dust generation and its dispersion in a longwall mine pose significant health and safety issues. The concern is prominent at both the working face, where coal excavation exposes workers to high dust concentrations, and also in the return, where float dust accumulates. To address this issue, researchers at theUniversity of Kentucky designed and fabricated a flooded-bed dust scrubber integrated into a full-scale physical model of a longwall shearer. This mock-up was installed in the longwall test gallery at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). A full-factorial experiment was designed to measure the effectiveness of the scrubber on dust capture. Test results indicated dust reduction of up to 57% in the return airways. This paper presents the development of a computational fluid dynamics (CFD) model and its validation by comparing the simulation results against the experimental results. The CFD simulations show good agreement with experimental results with differences between + 6.9 and − 9.7%. The validated CFD model was used further to predict the scrubber performance under additional operating conditions, resulting in a dust reduction of up to 66.5%. With this level of success, the scrubber concept can be a game changer for the mining industry, and it can be utilized to improve health and safety in longwall mines.

May 26, 2020

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls were a big part of the problem. They killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, which is the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How was this historic goal achieved? This paper starts with a modern analysis of the causes of the roof fall fatalities in 1968. Then it follows the reductions over time by category, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The paper shows that in 1968, more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Jul 1, 2023

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By Aijuan Zhang, Liang Zhao, Yutao Wang, Yu Bao

In the green backfilling mining of underground coal mines, gangue in a coal seam is used to replace and fill goafs. However, the gas drainage time changes in the amount of gangue output and order in the extraction sequence of stope blocks, thereby changing the production output. A multi-objective integer programming model was proposed to solve this based on an improved non-dominated sorting genetic algorithm. The results show a feasible gangue filling rate can be found and the extraction sequence for a long-term planning time is optimized. It increases the planned annual output by 26% and reduces equipment idle time.

May 23, 2022

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002