Search Documents

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By Johan Bosch, Wout Broere, Minh Ngan Vu

"INTRODUCTION Shield tunnelling is often used in constructing underground infrastructure in cities due to the ability to limit settlements and damage to existing buildings. However, in an urban environment with soft overburden and buildings on pile foundations such as the North-South Line project in Amsterdam, there is a tendency to design the tunnel well below the surface and below the pile tip level in order to reduce interaction between tunnelling process and piles. This results in deep tunnels and deep station boxes. When the tunnels are located close to the surface and above the pile tip level, this would reduce the required depth of the station boxes and the construction cost. Moreover, other benefits of shallow tunnels are the low operational cost in the long-term and shorter traveling time from the surface to the platforms. Still, the tunnels should be constructed in such a manner that existing buildings are not structurally damaged, which results in a minimum required distance between tunnelling process and existing buildings. In this paper, the extent of the area that is influenced by tunnelling will be investigated in order to determine the limit distance from tunnelling to existing foundations without inducing too large building deformation. From analysing empirical data of many shield tunnels, Peck (1969) firstly presented the settlement trough on the surface induced by tunnelling in soft soil as a Gaussian distribution. This is also confirmed by other authors (Cording and Hansmire, 1975; Mair et al., 1993; Ahmed and Iskander, 2010). In this study, the Gaussian curve is used to investigate the ground movement when tunnelling in order to find the effects on existing structures. Based on the results from centrifuge test and empirical data, Mair et al. (1993) showed that the subsurface settlement profile distributes as the Gaussian curve also. The width of settlement trough at the depth z depends on the depth of the tunnel z0 and a coefficient K depending on depth. Other studies by Moh et al. (1996), Grant and Taylor (2000) and Jacobsz (2003) based on Mair et al. (1993) proposed a limited change of K in various kinds of soil."

Jan 1, 2016

By Pierre Longtin

"Replacing the aging roadway access to the iconic Golden Gate Bridge, thereby ensuring traffic safety and robustness in case of seismic occurrences, provided an opportunity for major design improvements as well as the development of a parkway that would include the construction of four new tunnels. With an eye to the future, the Doyle Drive replacement project aimed to meet the highest standards for environmental stewardship beyond regulatory requirements. Understanding that lighting equipment is the tunnel‘s subsystem that uses the most energy, the operator was looking for a sustainable solution to light the tunnels. An Intelligent Lighting Control System (ILCS), designed specifically for road tunnels, was acquired to individually control the almost 2000 luminaires lighting the four tunnels. This paper will show the results in terms of energy and operational savings generated over the nine months of operation between the commissioning and the conference in April 2016. INTRODUCTION Electrical & mechanical (E&M) equipment represents an average of 10 % of a tunnel total construction cost. Once the civil infrastructure completed, E&M equipment drives the main part of the expense during a tunnel useful life. Table 1 below describes the impact of various types of energy consumption and their cost impact in tunnels of less than 500 m. It is clear that lighting is the sub-system that requires the most energy. A good lighting strategy is the key to reducing energy consumption due to lighting and a viable solution that will bring important savings in tunnel operations.With a price of $0.14/kWh in California and a planned increase between 3% and 6% per year during the period 2013-2040, the tunnel operators could not afford to overlit the tunnels—particularly when they have to operate it for the next 30 years. However, they also need to maintain the right lighting level to ensure driver safety all the time. The Presidio Parkway project includes the Battery tunnels, which are 240 m (790 feet) and 230 m (750 feet) in length, and the Main Post tunnels, which are 280 m (920 feet) and 315 m (1030 feet) in length."

Jan 1, 2016

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By Marini David, Pigorini Andrea, Fuoco Stefano, Zurlo Raffaele

"The excavation of a tunnel in highly weathered and strongly fractured rock masses due to tectonic actions is still a challenge. In order to maintain reasonable productivity, excavation through a wide zone of highly tectonized rock mass requires a detailed, integrated study of the construction solutions and a monitoring system to minimize the process time and to optimize the adopted consolidation measures in accordance with a predefined matrix of possible support systems. This paper summarizes some interesting data acquired during the excavation of the Brenner Railway Base Tunnel system between Italy and Austria. The Brenner Base Tunnel (BBT) runs through the fault line between the European and the African tectonic plate. This big fault zone is called “Periadriatic Line.” In particular, data acquired in the exploratory-service tunnel have been analyzed. Furthermore, the base concepts for defining the consolidation and support solutions adopted for the excavation of the exploratory tunnel are described. INTRODUCTION The Brenner Railway Base Tunnel (BBT) is a system of underground structures and tunnels that is designed to connect Italy and Austria using new railway standards. It is based on high speed (HS) concepts and applies the European Standards for Interoperability (TSI). The railway includes twin tunnels for a total length of about 55.0 Km without considering the connection tunnels to the existing underground railway in Innsbruck. Including the latter, the total length of the tunnel system reaches 64 Km, and is among the longest tunnels in the world. The Italian section passes through the so-called ""Periadriatic Line,"" which is an important tectonic structure generated by the collision between the European and the African tectonic plates. Despite the extensive investigations carried out (boreholes down to 700 meter depth), significant geological and mechanical uncertainties inside the Periadriatic formations remained unsolved. In order to elevate the level of confidence and observe the behavior of the rock mass at a representative scale, the BBT Authority decided to excavate in advance the service tunnel, which has taken the function of an exploratory tunnel. The data and observations collected during its excavation would provide important insights for the design of the main tunnels."

Jan 1, 2016

By Jacob Mathis, Mark Bradford, Alston Noronha, R. M. True

In June 2022, Louisville MSD completed a 6.5-km (4.0-mi), 6.1-m (20-ft.) diameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. For large diameter shaft and tunnel construction, drill-and-blast operations among other methodologies were used in close proximity to federal, commercial, and residential properties with no impact to stakeholder infrastructure. s one of the rst maor tunneling proects in Louisvilles metropolitan area, this paper explores Black & Veatchs rigorous geotechnical instrumentation monitoring program that provided uality assurance for local stakeholders and afrmed innovative tunneling solutions can be successfully executed in an urban setting.

Jun 23, 2024

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By James Corcoran, Richard McLane, Matt Neuner, Joseph DeMello, Hugh Davies

The Los Angeles County Metropolitan Transportation Authority (LA Metro) Purple Line Extension Section 1 (PLE1) is a $3.12 billion USD design-build, underground heavy rail project, connecting an existing station at Wilshire Blvd. and Western Ave. and extending 3.92 miles under Wilshire Blvd, terminating approximately 550 feet west of Wilshire and La Cienega Blvds. The project alignment runs immediately adjacent to the La Brea Tar Pits, world renowned for Pleistocene fossils and continuous seepage of asphaltum (locally known as tar) and gas in an urban setting. This paper presents a successful case history of the planning, design, and construction efforts to safely construct the bored tunnels through Reach 3 of the alignment (between Wilshire/Fairfax Station, and Wilshire/La Cienega Station), in a designated Methane Zone in the City of Los Angeles. Historical context on decades of challenges and studies is summarized. Further, this paper outlines the pro-active partnership between the Owner: LA Metro, the Design Builder: Skanska-Traylor-Shea Joint Venture, and geotechnical design services provided by Golder Associates to safely manage pressurized face tunneling through a confined gas zone near the La Brea Tar Pits. Specifically, a program of in-situ oxidation and soil gas extraction was designed to test and analyze risks associated with pressurized face TBM tunneling through the complex subsurface geological conditions, then implemented during construction. In advance of tunneling, a network of wells was used to draw air into the gas zone to oxidize the 6,500 ppm hydrogen sulfide gas, as well as determine methane recharge rate. During TBM tunneling, the wells were converted to a gas extraction system to evacuate, filter (H2S) and burn (CH4) the gas as the Tunnel Boring Machine passed, providing a preferential pathway for the gas to migrate toward extraction wells, and preventing the migration to adjacent buildings. The team extracted and treated 3,857,000 cubic feet of mostly methane gas over 40 days as the TBMs passed through the zone. Gas behavior, pressures, and concentrations were monitored not only from the extraction system, but also in basements and utility vaults along this section of the alignment.

Jun 13, 2023

By Shu Fan Chau, Innes Duncan, Harry Asche, Bill Newns

The North Auckland Line (NAL) in Northland, New Zealand, is being upgraded to pass Hi-Cube containers. The line includes many tunnels and bridges which need to be refurbished to improve structural clearances and line capacity. Tunnel 2 along the line, the Makarau Tunnel, has posed special challenges. Opened in 1898, the tunnel suffered multiple collapses during construction and has shown significant distortion during operation. The tunnel has been repaired many times since opening. Successfully enlarging this delicate and distressed structure has involved historical research, advanced analysis and design, and careful construction. The results provide lessons for dealing with brick lined tunnels and poor ground conditions

Jun 13, 2021

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By Robert Sturk, Knut O. Halvorsen

"INTRODUCTION AND BACKGROUND The world needs visionary people to break new ground and bring development forward. The human race has an inherent power and lust to explore and push borders, but also to connect and bring people together. Transport of people and goods has through history been a key factor to develop societies and increase collaboration between people and regions. Today, in the era of globalization, efficient transport systems are still vital for further development. Often, ideas of bold projects, like long bridges or tunnels, have been raised long before those projects are realized and actually built. This shows that visions must gradually be transformed into feasible business cases and sustainable political solutions. In some cases also technological development is necessary to make visions come true. Isambard Kingdom Brunel, indeed a visionary engineer, completed the oldest underwater tunnel in the world when the Thames Tunnel in London was opened in 1843. This tunnel is still in operation and now part of London’s rail transport system. Another milestone for the tunnelling industry was passed when the 54 km long Seikan tunnel in Japan was opened in 1988 after more than 15 years of construction. This tunnel is presently the world’s longest railway tunnel. Together with the 50.5 km long Channel tunnel between the UK and France, which has the longest undersea portion 37.9 km, they constitute examples of pioneering engineering projects that bring the industry forward. In 2016, the Gotthard Base Tunnel will be opened and then becomes the longest railway tunnel in the world with its 57.1 km. The trend is obvious that tunnels throughout the world are getting longer and longer. The Brenner Basis Tunnel presently under construction will yet again break the record being 64 km long. Presently, a number of even longer tunnels are planned and under design, some of these also have very long subsea portions, e.g. Bohai Straight Tunnel (123 km), Irish Sea Tunnel (around 100 km) and the Helsinki – Tallin fixed link (approximately 90 km). Northern Europe sees an increasing demand on efficient transport corridors to meet the growth of freight transportation between the Scandinavian Peninsula and central-Eastern Europe. Sustainable solutions will be required, and a shift from road/maritime transports to rail is imperative. Consequently, this paper describes yet another visionary project, a fixed railway link between Sweden and Germany, the Shortcut, to enhance traffic between these regions and to make it greener. It is true that this project still requires some work from politicians, economists and engineers to be realized, however, building a 100 km long tunnel under the Baltic Sea may become reality sooner than we think."

Jan 1, 2016

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007

By Eddie Woods, Jon Hurt, Roger May, Paul Watson

The Channel Tunnel Rail Link (CTRL) will be Britain’s first major new railway for over a century—a high-speed line running for 109km (68 miles) between St. Pancras station in London and the Channel Tunnel. The new line has been under construction since October 1998 and the first phase will open in October 2003. The project includes22km of twin 7.15m ID TBM bored tunnels under London and the River Thames, and the 3km North Downs Tunnel, the first major NATM tunnel to be constructed in the United Kingdom since the collapse of the Heathrow Express Tunnels in 1994. This paper will discuss the design of these tunnels and describe the construction progress to date. The discussion will include details of segmental lining design, TBM specification, and sprayed concrete lining design.

Jan 1, 2003

By Thomas Schultheis, William Heron, Paul Watson, Colin Warren

This paper describes the geology and geotechnics associated with construction of the Thames Tunnel, part of the UK’s Channel Tunnel Rail Link (CTRL). The 2.5km long twin tunnels run beneath the river Thames at depths of up to 40m and are currently under construction. They pass through varying geology comprising alluvium, terrace gravels and chalk with flints and are currently being bored using Herrenknecht mixshield slurry tunnel boring machines (TBM’s). This paper outlines the lithology and engineering properties of each geological formation and describes the geotechnical processes, potential hazards and difficulties experienced in the works. A summary is given into the extent of the investigative work in terms of route selection, tunnel design, TBM optimisation and further details are provided on the geotechnical aspects associated with the construction of the tunnel approach structures and the tunnels.

Jan 1, 2003

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008