Search Documents

By Elisa Comis, Barbara Bitetti, Julien Pepiot, Stefano Lione, Francesc Rich

The new Lyon-Turin railway project involves the construction of a 57 km twin-tube tunnel between France and Italy. Pini France (project leader) and Systra-SWS are the designers of Construction Site 8 (CO8). This part of the project includes the construction of the tunnel portal on the Villard-Clément platform, two 2.8 km long tubes of the base tunnel in the direction of Saint Martin la Porte, the cross-passages between tubes and the niches. This paper presents the general approach followed to design the temporary support for the base tunnel, cross-passages, and technical rooms. The design of the temporary support accounts for the variability of the ground and water conditions, the excavation attended behavior, the construction planning and the identified geological hazards that could be encountered along the alignment. Particular attention is paid to the intersections between the tunnels both in terms of numerical modelling and construction methods and phases. Two types of intersections are present in the project: the intersections between the cross-passages and the base tunnel and the intersections between the base tunnel and the niches. 3D models have been developed for the tunnel intersections.

Jun 23, 2024

By Brian H. Zelenko, Patricia M. Perry

INTRODUCTION The environmental requirements of the next section of Washington, D.C. METRO subway tunnels present unique challenges to the Contractor. The 14th Street Tunnels contract includes twin 975 m (3200 linear ft) soft ground tunnels. A stringent environmental soil and groundwater monitoring and free product recovery program was specified by the owner. A project-wide dewatering program hinges on satisfactory completion of the environmental requirements. Implementation of the Contractor's environmental program is discussed, including the pros and cons of the program, as they relate to progress of the project. Environmental issues on tunneling projects have become an important part of the urban tunnel construction process. Delays associated with environmental issues can have a major cost impact on tunneling projects. This paper will discuss the first of five Washington Metropolitan Area Transit Authority (WMATA) tunnel and station contracts awarded in 1994. These contracts are part of WMATA's Fast Track Plan to complete the original 166 km (103 mile) system by 2001. As such, stringent environmental requirements have been specified as a part of these contracts to limit delays associated with local regulators in order that the tunnels may be constructed on schedule.

Jan 1, 1995

By Nestor M. Fillip

INTRODUCTION The Advisory Conference on Tunneling held in Washington, D.C. in 1970 under the auspices of the organization for Economic Cooperation and Development (OECD) forecast that $54 billion would be expended by member countries on underground construction in the 1970s. Construction activity since the Conference indicates the forecast may have been conservative. Statistics in the report indicated a vast increase in tunneling projects for mass transit, hydro-electric development, railroad tunnels, sewer and sewage retention reservoirs and water tunnels. Development of equipment is required to meet the demands for high speed excavation and provide tunnel driving systems with maximum efficiency and capability to sustain high speed advance rates. BORING MACHINE CAPABILITY During the last decade, use of Tunnel Boring Machines (TBMs) has increased. Where ground conditions and limits of machine design criteria permit, circular tunnel sections are either the only section , or an alternate sections specified in the documents: a TBM is either required or is an acceptable alternate means of tunneling. The evolution and acceptance of the TBM has had an impact on the construction and to a lesser degree on the mining industry. The traditional drill-blast-muck or "hand" mine

Jan 1, 1974

By Zhenqi Cai, Mike Lichte, Kimberly Kennedy

The Ohio River Tunnel is the first of three combined sewer overflow tunnels to be constructed under Allegheny County Sanitary Authority's Clean Water Plan. The project consists of a total of approximately 5.5 miles of 18-ft and 14-ft finished diameter, segmentally lined deep rock tunnels and smaller diameter dewater and flow connector tunnels, as well as 8 deep flow drop and access shafts varying from 25-ft to 70-ft in finished diameter and 130-ft to 170-ft in depth. This paper describes the project components and the primary engineering challenges faced during design, including tunnel alignments and shaft site optimization with tight right-of-way constraints and multiple railroad and highway crossings. Assessment of tunneling methodology as well as tunnel and shaft designs and constructability included overcoming 5-bar hydrostatic pressure, abrasive bedrock, and the selection of the appropriate support of excavation systems in high-permeability alluvial soils adjacent to the Ohio River.

Jun 23, 2024

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By William Hodder, Lisa Smiley, Ehsan Alav

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km and be lined using a precast concrete segmental tunnel liner with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT liner was grouted through ports drilled in the segments. The Westerly Storage Tunnel (WST) in Cleveland will extend approximately 2.93 km long and will be lined by using a similar precast concrete segmental tunnel liner with an internal diameter of 7,620 mm and external diameter of 8,230 mm. The WST liner was grouted using both grout ports built into the tail can of the TBM and through segments. Each tunnel was mined primarily in shale with varying levels of weathering and both tunnels had dry and wet sections. This paper will document the means and methods for grouting in each tunnel as well as the methods utilized to proof grout and the results found.

Jun 13, 2021

By Robert W. Gordon

The art of excavating tunnels with continuous, full-face boring machines began almost 90 years ago, in the early 1880's. At this time, Colonel Beaumont designed and manufactured a seven-foot diameter tunneler for boring under the English Channel, Despite the absence of modern materials and manufacturing techniques, Beaumont's tunneler, powered by compressed air piped in from the surface, was quite successful. During its short, but impressive existence, this machine set a record of advancing in chalk 50 feet per day for 53 days - which is impressive even by today's standards. Despite the apparent success of this early tunneler, almost 80 years passed before any further significant development was accomplished in this field. Demands from the construction and mining industry and society itself have motivated the development of the modern tunneling machine. Our rapidly growing civilization needs faster, less expensive and safer means of excavating tunnels. Space age technology and materials have played a major role in making hardrock tunneling machines possible.

Jan 1, 1970

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By Shawn McWilliams, Aini Sun, Mike Lichte, Greg Colzani

The Allegheny County Sanitary Authority (ALCOSAN) adopted its Clean Water Plan (CWP) in May 2020, as part of a federal consent decree to comply with the USEPA’s Combined Sewer Overflow (CSO) Control Policy. Planned improvements include constructing a new regional storage/conveyance tunnel system, promoting green infrastructure/ source control, and expanding the treatment plant. Preliminary planning for the tunnel system was completed in October 2020. The Ohio River Tunnel (ORT) project is the first of three tunnel projects that make up the regional tunnel system. The ORT project began final design in 2021. This paper discusses the advancements made to the ORT preliminary planning concepts considering property availability, alignment optimization, tunnel boring machine evaluation, contract packaging and delivery schedules.

Jun 13, 2023

By S. Maurhofer

The Uetliberg Tunnel in Switzerland is the longest tunnel in Zurich?s new Western Bypass Expressway, connecting the Birmensdorf bypass in the west with the existing Zurich-Chur national motorway in the east. Thus the tunnel links the Zurich-West motorway interchange with the Zurich-South interchange (shown in Figure 1). The Uetliberg Tunnel project comprises two parallel tubes, each about 4.4 km long. The two tunnel tubes are connected every 300 m by a transverse walkway and every 900 m by a transverse roadway (Figure 2). The SOS niches are spaced 150 m apart. Portal stations with machinery rooms are located at the west and east portals. The tunnel falls with a gradient of 1.6% from the west portal at Wannenboden to the east portal at Gänziloo. The Project costs are about CHF 1.12 billion. The carcass construction started in March 2001. The Opening of the Uetliberg Tunnel is planed in spring 2009.

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By Jozef F. Zurawski

River Des Peres Foul water Interceptor (Skinker–McCausland Tunnel) is a gravity sewer tunnel constructed to eliminate dry sewage overflows during high river stages and to improve the wastewater collection and treatment. The original 78-inch (2m)finished diameter Skinker-McCausland Tunnel started as a 21,500 feet (6.5km)interceptor with 13 work, drop and access shafts. The tunnel constructions included soft ground, mixed face and rock tunneling in karst formation with maximum overburden of 175 feet (53m). Due to the success of the project, the tunnel alignment was extended another13,361 feet (4.1 km) and 7 new structures by negotiating two additional segments with the contractor and the designers.

Jan 1, 2001

By Roy C. Fedotoff, Jon Hurt, Gregg Sherry, Gilbert Tang

The 1,380 m (4,200 ft) long New Crystal Springs Bypass (Polhemus)Tunnel (NCSBT) will replace the existing Crystal Springs Bypass Pipeline. This tunnel project is part of the SFPUC’s $4.3 billion capital improvement program to repair and seismically upgrade their aging pipelines, tunnels, reservoirs and dams that provide drinking water to more than 2.4 million customers in the San Francisco Bay Area. This paper describes the development of the tunnel alignment and design, and the complex ground conditions of the Franciscan Mélange. Of particular interest is the challenge of tunneling with a possible downhill grade of 3%, a rigorous environmental process and incorporating the lessons learned from 1960s construction of the adjoining Crystal Springs Bypass Tunnel.

Jan 1, 2007

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By Steve Klein

The Transbay Downtown Extension (DTX) in San Francisco involves the construction of a large-span tunnel with a width ranging from 43 to over 60 feet. The tunnel will be excavated using the New Austrian Tunneling Method (NATM), also known as the Sequential Excavation Method (SEM), in highly fractured and sheared rock. This paper discusses the FLAC (Fast Lagrangian Analysis of Continua) analyses that were completed for conceptual design of the tunnel support system and to develop surface settlement estimates for the evaluation of measures to protect existing buildings located above the tunnel from damage.

Jan 1, 2008

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008