Search Documents

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By L. Figueroa

Electrochemical methods have potential to treat waters impacted by mining, while simultaneously producing a recoverable metal product to off-set treatment costs. Mining-impacted waters may present challenges with electrochemical treatment due to low concentrations and complex solutions of numerous dissolved metals. This paper presents an evaluation of the potential strengths and limitations of abiotic electrowinning of mining-impacted waters. In particular the impacts of chemical composition on metals removal are evaluated. Results of bench-scale experiments demonstrate the potential to remove metals on the cathode (copper, cadmium, lead), as well as the anode (manganese). Pre-treatment for iron and aluminum may be needed and post-treatment pH adjustment would be necessary. INTRODUCTION Due to continually increasing demand for metals, new technologies and innovative applications of existing technologies are needed to recover metals from mining-impacted waters. Electrochemical methods have long been used for metallurgical processes with solutions containing high concentrations of the target metal. However, electrochemistry also has potential to treat waters with lower metal concentrations, while simultaneously producing a recoverable metal product to offset treatment costs. Electrochemical water treatment may have several benefits over traditional alkaline treatment for acid rock drainage (ARD). Sludge produced from alkaline treatment has high water content that is difficult to dewater, even for treatment plants producing a relatively high-density sludge. For example, the Argo Tunnel Water Treatment Facility (Argo Facility) in Idaho Springs, Colorado uses hydrated lime to produce a high-density sludge with a solids content of 20 to 25 percent and filter cake with solids content from 30 to 35 percent [1]. Furthermore, costs for managing the sludge are significant, approximately $90,000 per year for treating approximately 150 million gallons of water [1]. Although not the case for the Argo Facility, sludge produced from alkaline treatment of ARD has potential to be classified as hazardous. Disposal of sludge also opens up the potential for future liability depending on the sludge’s chemical stability and methods of disposal. In contrast to alkaline treatment, electrochemical treatment produces metals in elemental and other highly-dense forms on the cathode. If metals concentrations and flow rates are sufficiently high, the metals recovered may help offset overall treatment costs. In addition, sludge production would be reduced, if not eliminated altogether, thereby reducing both disposal costs and potential future liabilities as well.

Jan 1, 2019

By Jon “Ike” Isaacson, Frank Perrone, Eric Prantil

"Tunneling through an urban environment carries many inherent risks to the immediate local infrastructure and subsequently to the project stakeholders. On the CQ031 Contract of the East Side Access Project in Queens, New York, twin 22.5’ diameter Herrenknecht Slurry TBMs were mined within close proximity to many infrastructure assets, with cover of less than half a shield diameter at times. Multiple public bridges and critical railroad infrastructure including catenary poles and signal towers supporting the busiest rail interlocking in the United States required underpinning systems. The support program for these structures was refined over the course of the four tunnel drives. It is the intent of this paper to show how the interaction between the temporary structures, instrumentation monitoring plan, and risk assessment program melded to provide a system which the owner, contractor, and designer relied on as a tool to ensure the project success without impacting the public surroundings. PROJECT BACKGROUND The East Side Access (ESA) megaproject located in New York City, N.Y is a multi billion dollar program for the Metropolitan Transit Authority Capital Construction (MTACC) with the main goal of bringing the Long Island Railroad (LIRR) commuter rail to Grand Central Station located in the heart of Midtown Manhattan. When completed, the project will significantly reduce congestion both into and out of Penn Station, the current terminus of the LIRR. In order to accomplish this, multiple contracts of varying scope are required to operate simultaneously in both Queens, N.Y and Manhattan. In 2009, the CQ031 Queens Bored Tunnels Contract was awarded to the joint venture of Granite Construction Northeast, Traylor Bros. Inc., and Frontier Kemper (G.T.F). The main scope of this contract was to excavate four segmentally lined soft ground tunnels underneath the Sunnyside Rail Yard in Queens, New York. Additional scope of work included the construction of a tunnel approach structure, electrical substation, and multipurpose ventilation and egress facility."

Jan 1, 2016

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By D. J. Brunner, S. Mathur, D. McKinney

With the advent of faster micro-processors, the use of numerical methods to simulate complex fluid dynamic phenomena in three dimensions for use in design has become prevalent in the automotive, and turbo-machinery industries. The Computational Fluid Dynamics (CFD) method divides the region of interest into small control volumes which form the mesh representing the physical characteristics of the problem, and uses the finite volume method to intergrate the equations for the conservation of mass, momentum, energy and species over each control volume. Recent developments in CFD software expedite mesh generation, and enable the use of unstructured grids, comprised of tetrahedral volumes in three dimensions and triangular areas in two. CFD more accurately represents complex geometries and allows for relative movement of meshes enabling simulation of multiple moving bodies. 'ibis paper presents two examples of how CFD simulation can be used to assess mine and tunnel ventilation problems formerly addressed by application of analytical solutions which were developed assuming ideal incompressible conditions. CFD simulation is used to evaluate the impact of varying the airflow in a descentionally ventilated airway on the layering along the roof of smoke and hot gases resulting from a vehicle fire. Control of the smoke layer is required to enable safe egress from the vehicle, particularly if the vehicle is for personnel transport, and to ensure control of the fire contaminants throughout the ventilation system. The airflow required to prevent layering against the ventilation direction, calculated from the Bakke and Leach relations (Bakke and Leach, 1962), is compared with the CFD simulation results. An evaluation of the pressures, generated as a vehicle enters a tunnel portal, using CFD simulation, is also presented for unflared and flared portal configurations. These simulation results are compared with predictions derived using an analytical method which assumes one-dimensional and incompressible flow. Results of the CFD simulation are presented in an animated video format. SIMULATION OF BACKLAYERING In designing a ventilation system for a transit tunnel, the ability of the ventilating air to control and prevent backlayering of smoke and hot gases resulting from a vehicle fire is of prime concern. The buoyant nature of hot smoke causes it to rise relative to the colder, fresh air provided by the ventilation system. If the vehicle fire occurs in a descentionally ventilated tunnel, the smoke may tend to move upgrade in a layer above the incoming ventilation airflow. The layer may become thick enough to engulf a substatntial part of the tunnel cross-section upgrade of the incident that comprises the evacuation route. This effect is termed "backlayering' and it is similar to the development of methane layers in mines for which most studies related to backlayering have been done. Prediction Techniques Analytical A number of studies have been conducted (Bakke and Leach, 1962) to define the characteristics of this phenomena and as a result have produced relations which are used both in the mine and transit ventilation fields to define the air velocities required to control layering. In the transit industry the air velocity required to prevent the backlayering phenomena from occuring during a vehicle fire is called the "critical velocity" (Associated Engineers, 1975) and is dependent upon a number of factors: tunnel height, cross-sectional area and grade; ambient air temperature and density; and the heat release rate of the fire. Common practice in transit ventilation design is to provide an airflow which meets or exceeds the critical velocity. In order to determine whether or not the critical velocity can be achieved with a particular ventilation system, a one-dimensional simulation of the tunnel network is typically performed using programs such as the Subway Environment Simulation program (SES) originally developed in the late 1970's (Associated Engineers, 1980). The results obtained from SES are compared to the critical velocity to determine the adequacy of the ventilation system. Computational Fluid Dynamics For the backlayering simulations, a commercial CFD code which has been used successfully in a wide variety of engineering applications, was used. It provides numerous options for modeling laminar and turbulent flows, multiple turbulence models, definition of multiple species and chemical reactions between them, a variety of boundary conditions (including constant pressure and constant velocity inlets) and the ability to apply user-defined FORTRAN subroutines. It includes the ability to model conductive, convective, and radiative heat transfer. FLUENT also permits the use of "body-fitted coordinates" to match the computational mesh or grid to complex real-world geometries. Computational Fluid Dynamics Model The model developed to simulate the backlayering phenomena is comprised of an airway of rectangular cross-section, 4 meters wide, 4.5 meters high, and 200 meters long. A laterally

Jan 1, 1995

By Samer Sadek, David I. Smith, Wai-shing Lee, Jeffrey L. Rice, Avelino Alonso

INTRODUCTION East Side Access (ESA) Contract CQ028 is located in the New York City Borough of Queens. The contract involves construction of a 230-meter (760-foot) long open-cut excavation with a permanent deck supporting Amtrak yard tracks over a semi-circular TBM launch wall on the east end, and the 36.5-meter (120-foot) long Northern Blvd. Crossing on the west end. The Northern Boulevard Crossing will be mined under an existing New York City Transit (NYCT) five-track subway tunnel; Northern Boulevard, a heavily traveled five-lane truck route; and an existing NYCT three-track elevated line; connecting to an existing open-cut shaft adjacent to the existing 63rd Street Tunnel bellmouth. When completed, Contract CQ028 will provide access for future Manhattan and Queens tunnel contracts. The footprint of the open-cut was determined by the geometric requirements of the future Plaza Interlocking facility to be constructed within in another future ESA contract. See Figure 1. This paper discusses design risk mitigations for the key elements of the contract, namely the Northern Blvd. Crossing and the semi-circular TBM Launch Wall. PROJECT OVERVIEW The Metropolitan Transportation Authority Capital Construction Company—East Side Access Project for the Long Island Rail Road will provide Long Island commuters with direct access to Manhattan’s East Side via a new rail line between the Harold Interlocking in Queens and Grand Central Terminal in Manhattan. The project connects the unused lower level of the existing tunnel under the East River at 63rd Street to new connecting tunnels in Queens and Manhattan. Contract CQ028 Scope and Construction Schedule This contract consists of the excavation of an open-cut from the east side of Northern Boulevard, through an existing MTA-owned rail yard and into the western limits of Amtrak’s Sunnyside Yard. The contract will connect to a completed open-cut

Jan 1, 2007

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984

By Charles R. Nelson

INTRODUCTION The support of openings in weak sandstones can be achieved by spraying on a liquid grout which will soak in and harden to form a shell. In the St. Peter sandstone of the Minneapolis-St. Paul area of Minnesota compressive strength is increased from about 0.7 MPa (100 psi) to over 7 MPa (1000 psi) to depths of 152 mm (6 in.). A shell of this strength and thickness can pro¬vide support much as shotcrete does but at lower cost. If the spray-grouted shell is inadequate for the support needed, it provides a good base for shotcrete application, which is often difficult in weak or friable sand¬stones because the fresh shotcrete peels off along with a thin layer of sandstone. The spray-grouted technique was initially developed at the Civil and Mineral Engineering Dept. of the University of Minnesota using funds provided by RANN Div. of the National Science Foundation. It was used as temporary support in a 3-m (10-ft) wide, 3700-m (12,000-ft) long storm water drain tunnel by the Minneapolis Sewer Construction Dept. Much of the field development at this construction project was carried out with the cooperation of the personnel of the city of Minneapolis. It also was used for temporary support in a 3.3-m (11-ft) wide, 1800-m (6000-ft) long storm water tunnel built in 1978-1980 for the Minnesota Dept. of Transportation in Minneapolis. In 1975, 2000 m (6500 ft) of 1.5-m (5-ft) wide utility tunnels were spray-grouted for final lining. A 50-m (150-ft) long, 1.2-m (4-ft) wide test tunnel built at the university in 1974 was sprayed for half its length and is being observed for long-term behavior which to date (1981) is good. GROUT MATERIALS The requirements for the liquid grout are more severe than those for injection grouting. Besides being able to penetrate the rock and develop sufficient strength, it must have the following properties: (1) be nontoxic, noncombustible, and have a low odor for spraying under¬ground; (2) have controllable viscosity and setting time for adjusting to the permeability of the sandstone and the required depth of penetration; and (3) must "wet" the sandstone and develop capillary "draw" to penetrate to the required depth. A sodium silicate-based grout with the proper setting agent meets these requirements in the local St. Peter sandstone which has a uniform grain size dis¬tribution curve with D,,, = 0.1 mm, permeability of about 10 to 20 darcys, a porosity of about 25%, and less than 5% of silt size or smaller. It is 97 to 99% pure SiO2. The grout mix consists of Philadelphia Quartz Co. Type N sodium silicate and Celtite 55 Terraset Spray Grade (SG) distributed by Celtite Inc., Cleveland, OH. A volume mix ratio of 100:9:125 for sodium silicate to setting agent to water produces a grout with two to four centipoise viscosity, and initial set at 20°C of 20 min. Setting time is temperature dependent, being longer at lower temperatures, but can be adjusted by varying the setting agent concentration a few percentage points. APPLICATION The application is simple. Spray the grout on the surface until the desired penetration is achieved. Penetration rates of about 5 mm (0.2 in.) per min. are realized in the St. Peter sandstone for up to 152 mm (6 in.) of penetration (30 min. of spraying). The set time must be longer than the spraying time. The spray nozzle should be moved back and forth at a rate that minimizes runoff due to surface buildup. Both a single large hand-propelled nozzle and multiple small machine propelled nozzles have been used successfully. The pumping and mixing equipment used consisted of: (1) a hand-held, hand-pumped, 11-L (3-gal) gar¬den sprayer for test patches (mix by shaking); (2) 76-L (20 gal) batch mixing in barrels with small electric pumps for spraying and mixing; (3) two component pumps consisting of Hypro Model 5300 piston pumps (Hypro Pump Co., St. Paul, MN) on a common shaft driven by an electric motor. The sodium silicate is premixed with a portion of the water and the setting agent is mixed with the rest of the water. The two components are combined and mixed just before the nozzle; and (4) a proportioner metering the setting agent just before the nozzle with the water and sodium silicate premixed and pumped from the surface. The proportioner permits the bulk of the grout to be pumped through a single pipe or hose with only the setting agent stored underground. This is efficient and low in cost. COST The grout mix costs about $0.20/L ($0.75 per gal) in 1978 dollars. Filling all the voids 100 mm (4 in.) deep (25% initial porosity) would have a materials cost of about $5.40/m2 ($0.50 per sq ft). The labor cost of application is usually less than the material cost for normal tunnel jobs. A pump and proportioner cost less than $1000. Sodium silicate storage tanks and pip¬ing costs would depend on the particular site conditions. REFERENCES AND BIBLIOGRAPHY Nelson, C. R., 1977, "Spray Grouting for Tunnel Support and Lining," Underground Space, Vol. 1, No. 3, pp. 241¬ 245. Yardley, D. H., Nelson, C. R., Stocker, T. H., 1974, "So¬dium Silicate Spray Impregnation of Tunnels in the St. Peter Sandstone," Research Report, University of Min¬nesota, 118 pp.

Jan 1, 1982

By QU Hong-lue, YANG Lin-han

Aiming at the subjective impact caused by subjective weighting method in the establishment of rockburst risk attribute identification and prediction model, the combined weighting method was introduced to eliminate the influence of unreasonable weight of each index. Eight discriminant indexes affecting the risk of rockburst were selected. Through the literature review, relevant rockburst cases were collected and 8 index rockburst sample sets were established. A variety of machine learning methods were used to analyze the feature importance of discriminant indexes in the samples, and then to determine the objective weight values of different methods. Combined with the subjective weights determined by the Analytic Hierarchy Process, the combination of weights were successively carried out. Based on the attribute recognition theory, the combination weights with different objective weight methods were established to identify the rockburst risk attributes, and verified by the confidence criterion. The results show that the objective weight value determined by the feature importance analysis of machine learning reduces the subjectivity of the weight of Analytic Hierarchy Process method, improves the prediction accuracy, and makes the prediction result closer to the fact.

Apr 26, 2022

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By W. R. Sharp

The ability to target, delineate, excavate, and produce local resources is essential to the establishment of man's long-term presence in space. Many procedures and equipment utilized to mine resources here on Earth may be directly applicable on the lunar surface, while others may need extensive redefinition and development. This paper compares, for a lunar base, the alternative of burrowing into and below the lunar surface with that of surface mining. A conceptual underground mechanical excavator is presented.

Jan 1, 1991

When most people think of coal mining, they envision men in soot-covered clothes and hard hats digging at deposits in deep underground caverns. These mental images commonly include coal cars rumbling on rails as they emerge from the earth, filled to the brim with rocky ore. The world of modern, longwall coal mining is a far different place. Yes, it?s underground, the miners still wear hard hats and the environment is filled with soot. However, today?s mining operations are carefully monitored and the entire process is highly automated. Five kilometers (3 miles) underground, a sophisticated, high-powered mining machine moves steadily through a 2-m (6-ft) high tunnel at an average speed of 3.2 km/h (2 mph), carving out coal, then conveying it to a crusher and carrying it to the surface. Instead of digging out the ore, a longwall mining system slices it from the exposed tunnel face, using giant rotating shears. The shorn coal tumbles onto a conveyer below the shears and is conveyed to the stageloader, where it is crushed and dumped onto the main conveyer belt that eventually hauls it out of the mine. Integral to the longwall shear and conveyor is a moving metal roof that protects it from the thousand plus feet of ground above. The ceiling panels automatically advance above the shears, powered by hydraulic roof supports that stand on the other side of the tunnel, moving in a slow, sideways lock-step with the shears. This complex and massive machine makes longwall mining the most ef?cient and productive method for excavating coal. In fact, it produces 2.7 kt to 22.6 kt (3,000 to 25,000 st) of ore per shift, versus 544 to 907 st (600 to 1,000 st) for the conventional room-and-pillar mining. Using that method, miners develop one section of a mine at a time after carving out load-bearing columns of coal to support the roof above their heads. Longwall mining also is considered safer than the room-and-pillar method, largely because the process is mostly automated, requiring fewer workers. Still, longwall mining has its drawbacks: The equipment is expensive and the mining conditions are harsh. An entire longwall system can cost between $50 million and $100 million, while the electrical controls used to operate it can cost an additional $1 million to $2 million. These investments grind away all day, every day, in hot tunnels filled with coal dust.

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By J. Herhold, S. Plaum

"Increasing worldwide energy demands, coupled with desires for cleaner energy, have led to greater research of renewable energies. Strongly weather-dependent energy sources, e.g. solar and wind energy, are unable to provide a constant control energy to withstand the fluctuation of the extensive power systems during peak hours. The pump storage plant Nant de Drance in Switzerland will not only have the capacity of a nuclear power plant, producing 900 MW, but will also combine the environmental aspect and the demand for controlled energy. Nant de Drance is one of the pioneer projects for upcoming energy challenges and serves as a model for future pump storage plants. This paper focuses on the planning process and the project execution of interdisciplinary large-scale projects such as Nant de Drance, including project related data handling, communication systems and project handling skills. Furthermore, the paper discusses mining excavation in the context of large scale projects and their regional environmental challenges, e.g. high alpine rock mass on the site of Nant de Drance. PROJECT BACKGROUND Project Overview Nant de Drance is a 900 MW pump storage plant located in the Swiss Alps. To provide such a high energy storage, six turbines (reversible Francis type), each with a capacity of 150 MW, were installed. Due to the efficiency factor of 80% the pump storage plant is able to provide an energy production of 2500 GWh per annum. Construction of the pump storage plant, which has been selected as “Major Tunneling Project of the Year” in 2014 by NCE and ITA-AITES, will be completed over 10 years. Therefore, the project has been divided in six major phases outlined below: - Launch: 2008 - Access Gallery: 2010 – 2012 - Excavation KMA, KTR: 2011 – 2014 - Concreting KMA, KTR: 2014 – 2016 - Installation of HEM equipment: 2014 – 2018 - Tests & entry into service: 2017 – 2018 Figure 1 outlines the single process phases of the project. For the construction of the shafts, galleries and caverns, 1.7 million m³ of metamorphic rock with sedimentary origin (mica schist & paragneiss of the massif „Aiguilles Rouges“) were excavated. A tunnel network with a total length of 15 km was created. The machine cavern measures 194 m long, 32 m wide and 52 m tall."

Jan 1, 2016

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016