Search Documents

By B Tutmez

Determination of stress-strain behaviour of rocks plays a crucial role in understanding the response of rocks during loading. However, it is a tedious, expensive and a time-consuming process to obtain such characteristics both in the laboratory and in situ. On the other hand, non-destructive testing methods such as ultrasonic velocities can produce a reliable and fast solution to indentify state of strain and stress in rocks. The present paper aims to provide insight into the relations amongst ultrasonic wave velocities, amplitudes and deformability properties of porous siltstone under compressive loading. For this purpose, pulse (vP) and shear wave velocities (vS) along with amplitudes (AP - AS), and applied loads with resultant strain were measured simultaneously so that response of siltstone to compression can be evaluated. In addition, initial vP and vS were recorded at the beginning of each test to calculate dynamic elastic properties of the specimens. This provided a comparison between static and dynamic elasticity properties of siltstone. Crack damage associated with the onset of dilation was also investigated. The results showed that there is a non-linear logarithmic relation between velocities and stress-strain level for siltstones.

Sep 26, 2011

By George Munro

Heavy water inflows of up to 1350 1/sec in the 19.6 km Moawhango-Tongariro Tunnel section of the Tongariro Power Development Scheme in New Zealand gave rise to severe operating problems, particularly in the equipment stripping stage when pumping installations had to be removed. Due to the necessity to commence stripping from the upstream side the contractors. Codelfa-Cogefar (NZ) Limited, took the decision to install a steel bulkhead some 5000m in from the lower. Tongariro, portal. The article lists the considerations taken in the placement of the bulkhead, and gives details of its design, installation and final removal. A brief description of the geology of the tunnel. together with water flow sources, rates and pressures is also included.

Jan 1, 1981

By Edward P. O'Hern

The importance of the so-called explosives and the increasing extent of their use are evident from the fact that the production in the United States for the year 1910, as shown by the United States Census reports, amounted to the enormous total of approximately 480,000,000 pounds, this being more than double the production of 1905 and more than three and one-half times that of 1900

Jan 1, 2015

By Robert Hopler

THE KEYSTONE NATIONAL POWDER COMPANY is an Independent organization, incorporated under the laws of the State of Pennsylvania. It has three dynamite mills near Emporium, Pa., with a daily capacity of 165,000 pounds. It maintains branch offices in practically all the largest cities east of the Rocky Mountains, and has distributing magazines located in every section where there is a demand for high explosives, with facilities for wagon deliveries. Our mills are all of modern type and are equipped with the most improved machinery for the manufacture of high explosives. The efficiency of our laboratory in conjunction with the high class of labor employed, has enabled us to put on the market an explosive, the quality of which is the result of extensive research and scientific knowledge. Our modern and complete equipment for harbor and railroad transportation insures our patrons of prompt deliveries, which is an essential feature particularly to contractors and those whose facilities for storage are limited.

Jan 1, 2013

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By W. A. MacWilliams, R. G. Reynolds

"This paper describes, for the first time, a patented method of extracting sodium sulphate from a natural deposit in Western Canada. The method resembles, but is not, strictly speaking, solution mining. The fact that a plant based on this method has been in successful operation since late 1969 will be of added interest. The deposit in question is located near Metiskow, Alberta, and conventional surface recovery methods could not be applied because of heavy concentrations of mud. Considerable pilot work went into the separation and recovery process on which the plant operation is based. The history of the industry is covered briefly as background to this development. Today it is clear that the method has broader application within the industry and, in concept, may generate interest in many other applications."

Jan 1, 1973

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By James J. Scott

Friction Rock Stabilizers, trade name II Sp 1 it Sets'" have been under research and development by the author and the Ingersoll-Rand Company since February of 1973. The United States Bureau of Mines and the Mines Enforcement and Safety Administration as well as many mining companies have cooperated in field testing the device. Split Set rock anchors are distinctively different from the widely used mechanical rock anchors or fully grouted rock anchors. They control ground movement internally in a manner that allows controlled deformation during the early phase of the ground reaction curve but then, as secondary creep develops, anchorage per unit length increases and they serve to strengthen and stabilize the opening for long periods of time. The history of research and development of the Scott Split Set rock anchor system with accompanying laboratory and field test data is presented in this paper.

Jan 1, 1977

"World Mining and Metals Technology" is the title of this year's SME-AIME Fall Meeting and Exhibit in Denver, Sept. 1-3, where a record number of exhibits are scheduled for display. The international theme is particularly appropriate, for in addition to the annual SME session, the Third MMIJ-AIME Joint Meeting will be held.

Jan 8, 1976

By W. E. MacDonald

This paper relates the story of 100 years of mining in the Harbour Seam at the Princess Colliery, Sydney Mines, Nova Scotia. Several interesting anecdotes are included along with the discussion of the evolution of coal mining methods in the area. Finally, some of the recently introduced equipment at Princess Colliery is described, and prospects for the future of the industry are outlined.

Jan 1, 1968

When looking for indicators for the mining business ? and these days who isn?t? ? one might need to look no further than the SME Annual Meeting. Held in Phoenix, AZ Feb. 28 to March 3, the meeting was, by almost any measure, a record-breaking success. Attendance included 4,937 industry professionals. Many of whom, feeling rejuvenated following the worst economic recession since the great depression, were greeted with a record 630 exhibits and 103 technical sessions covering all aspects of the mining and minerals business. Adding to the general optimism of the future was a celebration of the past and re-cent achievements in safety and health. The theme of this year?s meeting was ?Celebrating 100 Years of Mining Research? and the emphasis on advancements in safety was evident from the keynote address that kicked off the conference, to the field trips, to the Resolution and Safford mines that concluded the meeting.

May 1, 2010

It is my great pleasure as mayor of the city of Amsterdam to welcome you today to Amsterdam, and to the 10th International Conference on Piling and Deep Foundations. The history of Amsterdam has been connected intimately with your professions of geo-engineering and geotechnology, since its very first days. It is good to be aware that you are part of a very old tradition. The knowledge that we need today to build and renew the city has been gathered over a century long process so that we fortunately can stand on the shoulders of the giants before us. During the centuries people living in this part of the Netherlands have always struggled against the water. The same waters that brought the opportunity for a seafaring country to discover the world and to build an empire in the 17th century were a threat to the low lying Netherlands.

Jan 1, 2006

By Agne Rustan

The goal of this paper is to describe Fragblast 10 for those who did not have the opportunity to attend the Symposium and also give some examples of new research findings used in practise in some countries throughout the world. Also some entertainment events from the symposium are described.

Jan 1, 2013

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016

By Frank G. Snyder

The Precambrian of Midcontinent United States includes a metamorphic belt of probable Middle Precambrian age, a belt of Keweenawan volcanics and sediments, and widespread igneous activity that extended from Iowa to Texas. Most of the present structural configuration of the Midcontinent was developed by epeirogenic movements during the Paleozoic. The dominant elements are basins and arches. Three major metallogenic provinces occur in the Midcontinent. They include the Missouri Precambrian iron ores, the Lake Superior copper ores, and the Mississippi Valley lead-zincbarite- fluorite deposits. Several large iron deposits, occurring in rhyolite and andesite host rocks, are known. Both discordant massive bodies and replacement- type bodies occur. The iron deposits are believed to have been formed during the period of igneous activity. They are essentially the same age as the volcanics and older than the granites that intrude the volcanics. The Lake Superior copper ores include two established districts, the Keweenawan district and White Pine, and the copper-nickel deposits in the Duluth gabbro. The lead-zinc-barite-fluorite deposits include four major districts, Southeast Missouri, Upper Mississippi Valley, Tri-State, and Illinois-Kentucky, and at least eight minor districts. Ore may occur in stratiform deposits and in veins. The major districts all contain stratiform deposits, but several have produced appreciable quantities of vein ore. Only vein deposits are known in some of the smaller districts. The major features of all districts can be catalogued in terms of host rocks, structural patterns of districts, types of ore-bearing structures, and mineralogical characteristics. From these features, a Mississippi Valley type ore body, in its type area, can be defined.

Jan 1, 1968

By P. E. Weidmark

"PART I - Published PapersBallivy, G., and Dupuis, M., ""Laboratory testing for the design of grouted rock anchors""; Proc 6th Pan Am Conf Soil Mech Found Eng; Lima; 1:277-291; 1979.Ballivy, G., Ladanyi, B., and Gill, D., ""The effects of moisture content on the strength of fissured rocks""; Proc 1// 1ntnl Congr 1.A.E.G.; Madrid; //:2:7-16; 1978.Baumgartner, P., and Stimpson, B., ""Development of a tiltable base friction frame for kinematic studies of caving at various depths""; Int J Rock Mech Min Sci Geomech Abstr; 16:4:265-267; 1979.Bawden, W.F., and Roegiers, J.-c., ""Discussion and interpretation of the mathematics governing radial flow in a single horizontal rock fracture""; ISBN 07727-7002-6; Dept Civil Engng publication 79-11; Univ Toronto: 134p;1979.Chatterji, P.K., Smith, L.B., and Insley, A.E., ""Construction of Saline Creek Tunnel in Athabasca oil sand""; Can Geotech J; 16:1:90-107: 1979.Coates, D.F., and Gyenge, M., ""A case history of pit slope design""; Proc 4th ISRM Congr; Montreux, Switzerland; Sept 1979; 1:Theme IV:591-596; 1979.Crawford, A.M., and Curran, J.H., ""A dynamic direct shear machine for determining the time-dependent behaviour of rock joints"": Dept Civil Engng publication 79-08; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A displacement discontinuity approach to modelling the creep behavior of rock and its discontinuities""; Dept Civil Engng publication 79-09; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A higher-order displacement discontinuity element""; Dept Civil Engng publication 79-10; Univ Toronto; 1979.Cruden, D.M., ""A computer-based system for rock mass description""; Proc 1// Intnl Congr I.A.E.G.; Madrid; //:2:155-159; 1978.Cruikshank, D.J., and Curran, J.H., ""A.B.LE. approach to modelling of fluid flow in fractured rock masses""; Proc 7th Cdn Congr Appl Mech; May 1979; Sherbrooke, Que; 887-888; 1979."

Jan 1, 1980

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993