Search Documents

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Antonio Fabiano de Oliveira

The aim of the present research work is to study the influence of hard chrome covered skin pass cold rolling rolls using 2D/3D surface topography, i.e. roughness characterization. The common stochastic structure Shot Blast Texturing (SBT) does not meet all requirements related to the production line regards to the finished product. The Hard Chrome layer, applied on these SBT rolls, can improve the sheet surface quality and is of fundamental interest mainly for those steel mills that do not have another alternative to new surface structures such as those that may be provided by the EDT, LT, EBT, etc. methods. The function of the generated surfaces, obtained by these different methods is going to influence the tribological properties during the subsequent forming processes. On the other hand, they can increase the product final cost or require large investments to obtain such surfaces. The results here presented are in accordance with other recently published research work, showing that there is a relationship between these parameters, and that further detailed studies are needed.

Aug 17, 2017

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Dustin Vickress

The premature failure of copper staves in the lower stack and bosh is frequently the cause for an interim blast furnace repair at great cost to the blast furnace owner. Protective accretions may form on the stave hot face, but when these accretions are lost the staves can begin to deteriorate both due to abrasive wear from exposure to the descending burden materials and due to thermal cracking from exposure to hightemperature process excursions. These mechanisms can lead to failure of cooling passages, which forces blast furnace operators to shut off these channels, accelerating the rate of copper stave wear. Finger cooler technology was developed to extend blast furnace life by restoring cooling to damaged staves. Evidence for their effectiveness is presented herein in the form of experimental test work and conjugate heat transfer (CHT) analysis carried out using computational fluid dynamics (CFD) simulations. These tests demonstrate that under typical blast furnace excursion conditions, a stave fitted with finger coolers will undergo half the temperature rise of a stave fitted with conventional cigar coolers.

Aug 17, 2017

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Tiago Nunes Lima

As propriedades mecânicas de ligas TiNbSn são dependentes do processamento termomecânico. O refinamento dos grãos das ligas é obtido através de processos de conformação a frio, atingindo valores de redução que podem estar acima de 80%. Esta deformação a frio permite o aumento das propriedades mecânicas, mas pode reduzir consequentemente a ductilidade e a tenacidade das ligas. Este estudo tem como objetivo observar o efeito da laminação e forjamento a frio nas propriedades mecânicas de ligas Ti35Nb2Sn com 80% de redução. Foram realizados ensaios de tração, dureza, metalografia e microscopia das fraturas. Ambas as ligas deformadas e envelhecidas apresentam as fases ß, a” e ? em suas microestruturas, porém, com algumas mudanças microestruturais. Foi notado que a liga forjada possui maior resistência máxima a tração e dureza que a liga laminada.

Aug 16, 2017

By Lucas Teixeira Costa

A crescente demanda por aços ultrabaixo enxofre em usinas integradas a carvão mineral tem levado a esforços para reduzir o teor de enxofre no gusa e no aço. Todavia, a falta de uma visão integrada dos processos acarreta em otimizações isolados que nem sempre contribuem para uma efetiva redução de custos e aumento de produtividade final. No presente trabalho, foi construído e validado um balanço de massa capaz de realizar uma previsão do teor de enxofre de final de sopro a partir das entradas iniciais de enxofre na carga metálica e nas adições de fundentes. Para isso, considera-se que ocorre transferência de enxofre entre as fases, segundo seus teores e o coeficiente de partição de enxofre. A raspagem de escória de tratamento de gusa deve ser feita com muito cuidado para promover a melhor remoção da camada sobrenadante e ao mesmo tempo evitar perdas no rendimento metálico no processamento do aço. Utiliza-se o teor de enxofre do gusa carregado no LD como o principal parâmetro de controle, e recomenda-se que seu teor seja superior a 20ppm, uma vez que o esforço necessário para reduzir para teores abaixo desse limite será totalmente perdido no LD, devido à reversão durante o sopro.

Aug 17, 2017

By Anna Carolina Cerqueira Neves

As fibras sintéticas vêm sendo gradualmente substituídas por fibras naturais. Em comparação com a fibra sintética, fibra natural demonstrou vantagens econômicas e ambientais. Visto que apresenta características interfaciais com matrizes poliméricas que favorecem a absorção de energia de alto impacto pela estrutura. No entanto, até agora pouco foi avaliado sobre a fibra de cânhamo incorporada em matrizes poliméricas. Este estudo tem o objetivo de avaliar a resistência ao impacto deste tipo de compósito com matriz de poliéster reforçada com diferentes porcentagens de fibras de cânhamo. A resistência ao impacto aumenta proporcionalmente com a quantidade relativa de fibras incorporadas como reforço na matriz polimérica. Este desempenho foi relacionado com a dificuldade de ruptura imposta pelas fibras, resultante da interação da matriz de fibra de cânhamo / poliéster de forma a ajudar a absorção da energia de impacto.

Aug 17, 2017

By Willian dos Reis Lima

O aumento contínuo da produção de aço nas últimas décadas, fez com que usinas siderúrgicas se adaptassem a novas demandas a fabricação de aço. Este estudo teve como objetivo analisar os reatores que variam de 6-350 toneladas de aço vazado correlacionado seus parâmetros dimensionais e com a ajuda de uma ferramenta de extrapolação de dados, propor dimensionalmente um convertedor de 800 toneladas. Finalizando, verificando a correlação entre os aspectos importantes como: altura do nível do banho estático, relação de esbeltez e relação carga / volume. Os resultados mostram a grande variação dimensional entre os reatores. Em alguns casos, mesmo com capacidades semelhantes, os reatores são diferentes devido fabricantes diferentes. Em casos específicos, os reatores têm uma tendência para obter idealidade (volume específico igual a 1) ou superar com ele o nível adimensional tende a diminuir.

Oct 30, 2017

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017

By Lorenzo Bacchetti

Automatic yards with ad-hoc WMS (Warehouse management software), are the key for a modern and efficient warehousing which can face today logistic challenges. WMS boosts the traceability of material while optimizing the storage space. The operations in the yard are safer and logically organized according to algorithms that are specifically adjusted case by case. WMS can easily handle multi-cranes yard avoiding conflicts and increasing accuracy of positioning with decreased number of movements. The synergy of automatic cranes and WMS reduces bottlenecks and speeds up the preparation of deliveries with an overall improvement of warehousing and shipping scheduling.

Oct 1, 2019

By Márcia M. S. M. Pereira, Hervé Tavernier, Gérson T. Ferreira, Caio Nogueira Araujo Diniz, Fabio Luiz Lourenço, Wagner C. Moreira, Vinicius Cunha Aranda

Pós fluxantes desempenham um papel significativo na qualidade do aço durante o processo de lingotamento contínuo. Os pós fluxantes são escórias sintéticas usadas para lubrificar o molde durante o lingotamento contínuo do aço. Para que isso ocorra, o fluxante deve apresentar as seguintes funções: isolamento químico e térmico do aço, absorção de inclusões não metálicas do aço, lubrificação do molde e controle da transferência de calor entre o aço e o molde. O desempenho de cada função está relacionado às propriedades químicas e físicas do pó fluxante, que são dependentes de sua composição química e sua composição mineral, devido a sua relação com a taxa de fusão do material. A fim de garantir uma produção eficiente e de alta qualidade durante o lingotamento de um aço ultra baixo carbono, os pós fluxantes A e B foram investigados de acordo com diferentes propriedades físico-químicas. Diversos experimentos laboratoriais foram realizados para comparar o desempenho dos materiais A e B, visando à diminuição de captura da escória pelo aço no molde: avaliação do comportamento de fusão e fluidez, composição química e viscosidade. As temperaturas de processo foram avaliadas através de testes estatísticos, visando caracterizar o fluxo de calor e o trabalho de fricção durante lingotamento. Os testes industriais preliminares, realizados na Ternium Brasil, foram conduzidos com o objetivo de analisar o comportamento do pó fluxante durante a operação de lingotamento contínuo em relação a alguns aspectos operacionais e fornecer informações sobre sua influência na qualidade superficial do aço. Os resultados mostraram que, aumentando a viscosidade do fluxante, o consumo de pó tornou-se menor, levando a um maior trabalho de fricção e menor fluxo de calor no molde. No entanto, o comportamento da camada de escória mostrou que, apesar do aumento da força de atrito no molde, a espessura da escória foi adequada e não houve relatos de defeitos superficiais durante o uso do material fluxante de maior viscosidade.

Oct 1, 2019

By Edwan Anderson Ariza Echeverri

O aumento das exigências para reduzir o consumo de combustível e aumentar a segurança dos passageiros tem estimulado o desenvolvimento da nova geração de aços de alta resistência. Esses objetivos tornam-se atingíveis com a redução do peso dos componentes de aço do veiculo, pelo uso de chapas mais finas e resistentes, mas não menos dúcteis. Com esse propósito, no presente trabalho pretendeu-se analisar os efeitos de diferentes rotas de processamento: estampagem a quente, têmpera e partição e o inovador processo que combina a deformação a quente com a têmpera e partição. Os ciclos térmicos foram projetados para obter a maior fração de austenita retida, além de ferrita e martensita. Para cada amostra tratada, amostras de tração de tamanho reduzido foram extraídas de amostras previamente tratadas em simulador termomecânico avançado Gleeble 3S50. A microestrutura foi analisada por microscopia óptica e eletrônica de varredura. Com o novo processo combinado acredita-se que seja possível atingir uma boa associação de propriedades para a nova geração de aços de alta resistência pela transformação da austenita retida metaestável em martensita induzida por deformação, contribuindo para a absorção de energia durante impacto.

Aug 16, 2017

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Daniele Perondi

Diferentes resíduos são gerados pelas indústrias siderúrgicas, dentre eles o resíduo dos trituradores de sucatas (RTS). O RTS gerado pelas siderúrgicas brasileiras se difere dos demais países devido aos materiais que são alimentados no triturador. Assim, o objetivo deste trabalho foi avaliar as características do RTS gerado por uma siderúrgica brasileira. As seguintes técnicas foram utilizadas: identificação e quantificação dos principais constituintes, análise termogravimétrica, imediata, elementar, poder calorífico superior e teor de cloro e metais. Os principais polímeros presentes no RTS foram o poliestireno e o polietileno. A partir dos resultados de análise imediata, elementar e de poder calorífico superior do RTS, verificou-se uma elevada quantidade de matéria volátil (76,22% ± 6,90). Os altos teores de carbono (72,92%) e hidrogênio (9,86%), foram atribuídos à elevada quantidade de polímeros e borrachas presentes no resíduo. O teor de enxofre (0,21%) pode ser atribuído a presença de borracha no resíduo, enquanto o teor de cloro (1,33% ± 0,13) pode ser atribuído a presença do PVC no resíduo. O poder calorífico superior do RTS foi de 30,01 ± 1,22 MJ/kg, de forma que uma avaliação termoquímica mostra-se como uma técnica atrativa para a sua destinação final.

Oct 30, 2017

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018