Search Documents

By C. P. Proctor, E. D. Hummer, J. A. Younkins

COMPARATIVELY little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission of any effluent of high solid content to be replaced by clean water in order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the purpose of this paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settling and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." GENERAL ARRANGEMENT OF WATER SYSTEM So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers.1.2 The washer, which handles 0 to 4-in. raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. r) consists of twin 48-in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10 ½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By J. Visman

A simplified method of assessing the characteristics of a cleaning unit, including washability curves, yield figures, ash error, separating gravities, and error curve. FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, information that ultimately can be secured only from actual tests made in the laboratory or in the washery. It is not the purpose of the present discussion to compare the merits of various characteristics, but to describe the general method of calculation, including a method of obtaining data with a minimum of laboratory work. All data presented here were derived from tests made at the plant with portable field equipment, using small quantities of varsol, carbon tetrachloride, and bromoform. It will be explained later that the use of standard fractional ash contents designated normalized ash contents aids considerably in reducing the routine testing of coal cleaners. Like any other statistical procedure, this method has limitations, and it is not recommended for any work in connection with guarantees. Even a varying commodity such as coal, however, will follow the law of large numbers, which is the basic law of statistics, thus allowing simplification of test work without appreciable loss of accuracy. The characteristics needed for evaluating cleaner performance are normally derived from a float-sink analysis of samples of the clean coal and the refuse, followed by ash determinations of the various fractions. Usually a sample of feed is also collected to find its ash content and to make a single specific gravity cut, both in connection with determination

Jan 1, 1955

By J. E. Gould, H. J. Hand

MANY independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final deoxidation In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding over-deoxidation to minimize the amount of inclusions present and to make as sound a steel as possible For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or long FeO values The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishing the state of oxidation at a given time Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors Data obtained are from actual furnace operations, the metal test being of the spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States Steel Corporation This method of taking open-hearth metal temperature was invented by Collins and Oseland,1 and was developed into its present form by L 0 Sordahl,2 of the Research Laboratory The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications 3,4,5 Slag components were obtained by chemical analysis Data were taken from four 165-net-ton furnaces during the working period of the heat Recognizing that additions of ore affect the

Jan 1, 1942

By R. R. Brandenthaler

CONTROLLING -the pressure under which a well produces crude oil has advantages that are ap¬parently not entirely realized by many operators in the Mid-Continent district. The possibilities of utilizing well pressures are indicated by a series of ex-periments recently completed by the Bureau of Mines in which pressure control was successfully applied to 20 wells in, the Davenport field. The flowing period of all of .the wells was lengthened in some instances it was. more than doubled. The daily oil production from approximately one-half of the tested wells was in-creased. The amount of gas produced per barrel of oil was decreased, and this, in addition to a slower rate of decline in production, indicated that the ultimate re-covery had been increased. The successful application of pressure control to flow-ing oil wells must take into consideration the relation-ships existing between pressures in the different parts of the system which, though not equal, are nevertheless more or less interrelated. These relationships, which have such an important bearing on the results obtained by applying pressure control, are as follows: A change in rock pressure will affect the tubing pressure, casing pressure, and differential pressure, but it will not affect the trap pressure. A change in tubing pressure will affect the differential pressure and casing pressure; also, a change in casing pressure will affect the tubing pressure and differential pressure. Trap pressures are not affected by rock pressure, casing pressure, tubing pressure, or differential pressure, unless the traps are required to handle gas and oil beyond their capacity. Trap pressures will affect the differential pressure, tubing pressure, and casing pressure and any changes at the well-head, whether differential pressure, tubing pres-sure or casing pressure, will affect the pressures in the well. Any change in rock pressure results in a change in the tubing pressure, casing pressure, and differential pressure. When any sudden or unusual change in well-head pres-sures occurs (for example, an erratic tubing pressure), and when a sudden decrease in oil or gas takes place, it is al-ways advisable to note whether the trap pressure has changed. If the trap pressure has not changed, note whether the oil line from the trap to the flow-tank has become clogged, as would be evidenced by a rise in the oil level in, the trap. If the oil line is functioning properly, and if the trap pressure has not changed, the flow-line from the well to the trap should be inspected. If it is free from obstructions, then changes in the differential pressure, tubing pressure, and casing pressure must be due to changed well conditions.

Jan 4, 1927

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By B. H. Caudle, A. B. Dyes, R. A. Erickson

The study of the influence of fluid mobilities on the sweepout pattern resulting from the injection of gas or water has been extended to cover the production period which follows breakthrough of the injected material. Mobility ratios over the range common in field operations (0.1 to 17) were studied for several pattern floods (five-spot, staggered, and direct line drive). The experimental data required for these studies were obtained by the use of the x-ray shadowgraph technique using miscible oil phases of different viscosities in porous plate mode1s of a reservoir element. From the shadowgraph pictures obtained before and after breakthrough of the injected fluid, flowing ratios at the producing well and cumulative volumes injected were calculated. The method for applying such data in predicting field behavior is illustrated for a water flood of a five-spot. For this case a range of mobility ratios of 0.5 to 5.0 results in: (I) nearly complete (95 to 100 per cent) sweepout pattern efficiencies at abandonment conditions, (2) production after breakthrough being responsible for as much as one-third of the total recovery at the lower mobility ratios, and (3) a twofold variation in the operating life of the reservoir. In determining the merits of a secondary recovery operation, the fraction of the reservoir which is ultimately to be swept by the injected fluid is of major importance. Because of its significance a large amount of research has been applied to the study of areal sweepout efficiency. Muskat, Wyckoff and Botset1,2 have presented the classic analysis of the pattern efficiency at breakthrough for several injection patterns in which the mobility of the fluids ahead of the injected phase front was equal to the mobility of the fluids behind the front. Aronofsky3 as extended this analysis of recovery at breakthrough through numerical computations and by the stepwise use of the potentiometric model to include the effect of different fluid mobilities ahead of and behind the invasion front on the line drive performance. Fay and Prats' have also employed numerical computations to show the influence of one other condition of fluid mobilities on the five spot flood. In a previous paper' a new method of attack on this problem which employed x-ray and porous plates was described. At that time experimental results were also presented which described the effect of fluid mobilities on the reservoir area contacted by the injected fluid at breakthrough for the five spot and direct line drive patterns. Most of the literature pertaining to sweepout pattern efficiency has emphasized the pattern which is obtained at breakthrough of the injected phase. The increase in the sweepout pattern which occurs after breakthrough

Jan 1, 1955

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unex-pected, but that along with the factual discovery there is a constant effort to understand. It appears that one's interest in, and satisfaction with, the discovery of an array of new experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner. Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows. Of course, there have been long arid stretches in the history of physics in which new data of unquestioned ultimate importance have piled up, without much inspiration or illumina-tion in the way of understanding. For 50 years spectroscopy had such an arid history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered. The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the same sort of situation as spectroscopy before the advent of Bohr. A great many kinds of data were collected for a great many solid and liquid sub-stances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected. But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthu-siasm of the collector that kept me going. However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand It appears that. one's interest in, and satisfaction with, the discovery of an array of news experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows Of course, there have been long and stretches in the history of physics in which new data of unquestioned ultimate importance ham e piled up, without much inspiration or illumination in the way of understanding For 50 years spectroscopy had such an and history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the Same sort of situation as spectroscopy before the advent of Bohr A great many kids, of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By W. A. Tiller

SEVERAL authors1-6 have shown that, during solidification from the melt, the direction of formation of substructure boundaries depends upon the direction of heat flow and the rate of solidification of the metal. The most prominent of these observations was that a preferred orientation developed during the solidification of the columnar zone of an ingot which for face-centered-cubic metals was the <100> direction. Previous explanations1-&apos; given to account for this preferred orientation and the other boundary phenomena are all based on the premise that the phenomena are characteristics of the pure element. However, recent experiments by Rosenberg and Tiller7 have demonstrated that the preferred orientation in pure lead is the <111> orientation, and that the heretofore observed <100> orientation is due to the effect of solute on the mode of solidification of the metal. Teghtsoonian and Chalmers,4 studying striation boundaries in tin, and Chalmers and Rutter,5 studying corrugation boundaries in tin, showed that these substructure boundaries were aligned parallel to the axis of heat flow for slow rates of growth, and that the alignment varied from this direction as a function of the rate of growth. to approach the den-drite direction at high rates. Chalmers,6 studying the direction of formation of a grain boundary separating two crystals of different orientation, showed that at slow growth rates the boundary is parallel to the axis of heat flow, while at higher speeds it will deviate from this direction, sloping into the crystal whose dendrite orientation departs the most from the axis of heat flow. It is this phenomenon that allows certain crystallites in the chill zone region of an ingot to encroach on their neighbors and ultimately produce the preferred orientation of the columnar zone of the ingot. Since the previous explanations of this preferred orientation are unable to account for the recent observations,&apos; a new mechanism will be considered. This will lead to an explanation of the other substructure boundary phenomena as well. Investigations by Graf,8 Billig,9 Rsenberg,10 and others have demonstrated in a striking fashion that crystal growth takes place by the deposition of individual layers oriented along the close-packed planes of the material considered. This lamellar or

Jan 1, 1958

By Harrison Everett Ashley

Slimes are usually defined as all material passing a certain sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions; 150-mesh is common practice. The reader of the first two volumes of Richards&apos; is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemjcal constitution to show the widest possible divergence in physical properties.

Jan 1, 1911

By Henry H. Logan

THE purpose of mine-hoist safety controllers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper acceleration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoisting drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of mechanical hoist controllers, the basic elements of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical connections would cut off the power and set the brakes. Since in strictly mechanical hoist controllers valuable time was lost while the various mechanical movements took place, an important development was the invention of controllers partly mechanical and partly electrical. This type of controller has a governor and movable cams to be driven in synchronism with the hoist drum, the governor representing the hoist speeds and the cams profiled to form a pattern for retardation, representing the travel of the cages in the shaft. This type is also provided with an overspeed switch and usually with a pair of selective-limit switches, one for the top limit and the other for the bottom. In overspeeding or failure to retard in accordance with the profile of the cam, the overspeed switch will be opened, or if the top or bottom limit is overrun one of the limit switches will be opened, breaking the retaining circuit of a contactor or magnetic latch, causing the power to be cut off and the brakes applied. When the speed falls to the predetermined safe speed, the overspeed switch closes, and a hoist equipped with power-operated brakes controlled in emergency by a solenoid-operated valve can be restarted immediately by simply moving the master control lever to the "off" position and then applying power-unless brake interlocks are used, in which case the brake lever or levers must also be brought to the "applied" position, after which the hoist can be restarted in the usual way. When hand-reset weights instead of solenoid-operated mechanism are arranged to set the brakes for emergency, it is necessary to reset the weights manually, besides bringing the master control lever to the "off" position before the hoist can be restarted. Should a final limit be slightly overrun, and a stop made with a limit switch held open by a cam, it is necessary for the hoistman to use a "backing-out" switch which short-circuits the overrun limit switch, reestablishing the hoist-control circuit, and simultaneously opening the

Jan 1, 1940

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By J. Greenspan

The anisotropy of fracture and slip, that is, the brittleness and ductility of the beryllium single crystal, is characteristic also of po1ycrystalline beryllium in which the grains are oriented in a preferred manner. Beryllium with grain orientations resulting from hot working either unidirectionally or bidirectionally is ductile or brittle in directions given by the anisotropy and orientation of the grains. Textures developed from various hot-working sequences are given, and tensile results are correlated with textures. Not only texture, but fine grain size is necessary for obtaining high tensile elongation. Ultimate tensile strength and elongation are both correlated with grain diameter. Of particular interest is the case in which unusually high tensile elongations of 30 to 40 pct are obtained when basal planes are oriented to carry THE beryllium crystal (of nominal purity) is probably unique among metals with respect to its unusually acute anisotropy of slip and fracture. While extensive slip can occur on the system (1010) [ll20] starting at about 19,000 psi, the (0001) plane is particularly vulnerable to fracture at 4500 psi or less. Fracture occurs also on the (11zo) plane at about 26,000 psi.1"3 Further, there seems to be no other slip System which contributes significantly to

Jan 1, 1960

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949