Search Documents

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The arbitration process, and its drawbacks: Any time you have taken part in a major arbitration, and the decision, when it comes out, is not what you thought it would be (which is bound to happen occasionally), the normal reaction is something like æthe arbitrator got it wrongÆ. Again normally, when you have cooled down a bit, and you look in more detail at the decision, you can see, probably, æwhere he got it wrongÆ (it is only male arbitrators who get it wrong). Ultimately, when reason prevails, and you reflect on it, you can see that what really happened was that you failed to get the arbitrator to see what you were getting at in the point or points concerned. This is doubly frustrating, when you consider what has been involved in getting to this point, having been through it all at least twice. An alternative to this process may be the dispute review board.

Jan 1, 1999

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004

By M Yadav, K Clode, S Daykin

The mining industry faces numerous challenges related to sustainability and circular economy principles, necessitating strategic approaches to innovation and resource management. As demands for mineral resources continue to rise, mining companies are under increasing pressure to address environmental impacts, minimise waste generation, and optimise resource utilisation. These challenges underscore the importance of Research and Development (R&D) roadmaps as strategic tools for guiding innovation and sustainability efforts within the sector (Jochen Berbner, 2022). A design-led methodology offers a structured approach to R&D roadmap development, emphasising stakeholder engagement, collaboration, and alignment with industry objectives. By leveraging design principles, mining companies can ensure that their R&D initiatives are responsive to evolving challenges and opportunities, fostering a culture of innovation and continuous improvement. Against this backdrop, the project aims to address the pressing challenges associated with sustainability and circular economy in the mining industry. Through the development of R&D roadmaps and the application of a design-led methodology, the project seeks to identify innovative solutions for enhancing resource efficiency, minimising environmental impacts, and promoting sustainable practices within mining operations. This paper highlights the collaborative efforts among Isle, the mining industry, and water utilities, which have yielded tangible benefits. The study demonstrates how the outcomes from the roadmaps outlined below effectively align research with strategic objectives, fostering innovation to address pressing challenges.

Sep 1, 2024

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By R Urie

Dilution and loss of ore during the mining process invariably occur in all underground mining operations. This dilution and ore loss can have a significant effect on the performance and value generated from a mining operation. Further, excessive dilution or greater than anticipated ore loss during mining is often one of the key reasons for the underperformance of a mining project when compared to a feasibility study or annual budget. Mining professionals often go to great lengths preparing detailed mine plans, schedules and economic models only to then apply high-level estimates or rule of thumb values for dilution and mining recovery that can ultimately lead to inaccurate forecasts for the performance of a mine with the resultant loss of value due to the mining of uneconomic material or the loss of potentially valuable ore. This paper discusses processes and practices that can be practically used to manage dilution and mining recovery in an underground mining operation with a focus on understanding and then maximising value. The processes cover items such as the definition and measurement of dilution and mining recovery, techniques for the estimation of dilution and mining recovery, consideration of the economic implications, management of dilution and mining recovery through the stages of the planning cycle, and practices to reduce dilution and improve mining recovery. Common misconceptions and omissions are also discussed.

Mar 29, 2023

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

Effective domaining is fundamental to geostatistical modelling for grade control. Through analysis of lithological, structural and alteration logging data, effective groupings (domains) can be identified and employed for estimation or simulation purposes.The poor definition of domains can adversely affect the grade control model resulting in a misinterpretation of the optimal ore-waste boundary and ultimately reduces the quality of recovered ore. The implementation of an appropriate domaining strategy is therefore expected to improve recovery and reconciliation.A thorough understanding of the geology of the deposit and adequate sample data is required for selecting domains. For new deposits, a resource drill database and resource model may be the only information available. Where extension to a previous operation is taking place, historic grade control, mapping and exposed geology may be used to improve domain selection. Preconceptions about domains, should they exist, need to be re-evaluated and tested to ensure they are fit for the purposes of grade control.While mining progresses, the domain model is re-evaluated to ensure that the previous interpretation is still suitable for the present configuration and geology. The grade control process, being iterative, lends itself to regular review and continuous improvement as further data is collected during the grade control cycle. Regular updates to the geology model, mapping, geostatistical data analysis and review of variography will provide indications of a changing domaining environment.Narrow vein gold deposits, which may have several factors influencing mineralisation, present considerable domaining challenges. By scrutinising the data, sample populations can be grouped into domains, which not only improve ore recovery, but help assist in the development of a mine geology model.CITATION:Matthews, G D, Haylett, M E, Weeks, A and Khosrowshahi, S, 2014. Effective domain selection for grade control in narrow vein gold deposits, in Proceedings Ninth International Mining Geology Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P J. Bangerter, G D. Corder

With the societal desire and drive towards low carbon energy sources, there is a growing awareness of the important role that minerals and metals will play with renewable energy technologies. Copper is an essential metal for technologies that generate energy from renewable sources, in particular for wind and solar photovoltaic energy systems. A recent report (Arrobas et al., 2017) estimated that the median increase in copper demand through to 2050 for wind technologies and for solar photovoltaics would need to be 250% and 300% respectively to meet the goal of a 2°C global temperature increase scenario compared with a 6°C global increase, which is largely an extension of current trends (IEA, 2018). The aim of this extended abstract is to demonstrate with the necessary increase in copper production for renewable energy technologies that sound sustainability performance across the global copper value chain is to the benefit of government, society and industry.CITATION:Corder, G D and Bangerter, P J, 2018. Balancing the benefits and impacts of future copper demand – climate change and arsenic, in Proceedings Life-of-Mine 2018, pp 17–19 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M Johnson, M Horrigan

The scope of this report is to examine the aforementioned hypothesis by performing a detailed analytical comparison of a P&H electric rope shovel to an O&K diesel powered hydraulic excavator. In order to complement the integrity of the concluding results, two different size categories will be analysed in order to demonstrate that the findings can be extrapolated and applied to all the machinesÆ size classes. These two size classes are categorised by their bucket sizes and they are in the range of 43 - 58 cubic metres and 23 - 26 cubic metres. It should be noted that electric powered hydraulic excavators will not be considered in this report. In order to compare the electric and hydraulic types, the machine variants that will be analysed are commercial cost-effectiveness and operational flexibility. Although operational flexibility can be an ambiguous characteristic, a clear and thorough definition describing its exact meaning has been included. In order to simplify this study, all the data collected for this comparison have been for overburden removal, eliminating the variation that occurs with the movements of the shovel when selectively mining in the ore deposit. Thus, it ensures that all the data that is compared stems from a common origin for all the shovels. In other words the information will be compared when digging in the same material, loading into the same sized haul trucks, and when possible, with the same operators. Theoretical data received form the respective manufacturers, and actual data obtained from Mount Whaleback, was used for this comparison. This leads to the final comparison, where the operational flexibility and the cost-effectiveness are evaluated, with respect to their individual importance, ultimately influencing the final recommendation.

Jan 1, 2002

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

By J Wen, P Hou, W Yu, M Hu, Z Jiang, C Bai

Vanadium titano-magnetite (VTM) is one of the important iron ore resources in the world. High viscosity and low fluidity are the basic characteristics of hot metal containing vanadium and titanium during the ironmaking process. Clarifying the influencing mechanism of the melt viscosity would be a significant issue for the high efficiency smelting of VTM. In this paper, a self-developed melt viscometer based on the principle of torsional vibration theory was employed to measure the viscosity of hot metal accurately. Simultaneously, the thermodynamic calculations and some modern detection methods were also used to investigate the precipitation behaviour of high-melting-point phases in hot metal containing vanadium and titanium. The measuring results show that the viscosity of molten iron gradually increases with the increase of titanium content when the mass fraction of titanium is between 0.09 wt per cent – 0.50 wt per cent. Meanwhile, the viscosity of the hot metal was affected significantly by the vanadium content. When the vanadium mass fraction was higher than 0.30 wt per cent, the viscosity of hot metal increased sharply, which will have a serious impact on the fluidity of the hot metal. Furthermore, it was revealed by thermodynamic calculations that an increase in titanium and vanadium content would result in the precipitation of high melting point phases such as TiC, TiN, VC, and VN in the molten iron, ultimately resulting in a decrease in its fluidity. Meanwhile, it was confirmed by Scanning Electron Microscope (SEM) observation that the precipitates in the hot metal were compounds consisting of V, Ti, C, and N elements, which agrees well with the thermodynamic analysis results.

Aug 21, 2024

By D R. L Vedoy, L Botha, S P. Gumfekar, J B. P Soares

Most of the known in-place reserves of oil sands are found in Canada. These oil sands ores are mined using various processes to extract bitumen. The by-product slurry resulting from the extraction process, known as tailings, is discharged into tailings ponds. Fine kaolin clays are an important ingredient of the tailings because they remain suspended in water for many years. Current polymeric flocculation/dewatering technologies use acrylamide-based polymers such as polyacrylamide (PAM), but sediments produced using PAM-based flocculants hold considerable amounts of water due to the formation of loosely-packed flocs. Anionic polymers are better flocculants due to bridging and the charge-neutralisation mechanism. In this paper, we will compare the synthesis of two flocculants: thermosensitive, anionic flocculants and thermosensitive, hydrophobically modified anionic flocculants. The first flocculant is a copolymer of acrylic acid (AA) and N-isopropyl acrylamide (NIPAM), in which AA is the anionic monomer. The second flocculant is a copolymer of NIPAM, AA and the hydrophobic monomer N-tert-butyl acrylamide. We evaluated the dewatering efficiency of 2 wt per cent kaolin using both flocculants by comparing settling rates at different flocculant dosages, charge neutralisation ability and supernatant clarity. To better understand floc formation, we measured the floc size formed by both flocculants at different flocculant dosages. We propose that the hydrophobic monomer in the terpolymer flocculant helps expel water out of flocs, ultimately decreasing the water content in the sediments.CITATION:Gumfekar, S P, Vedoy, D R L, Botha, L and Soares, J B P, 2015. Thermosensitive, hydrophobically modified anionic flocculants for dewatering kaolin clays, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 45–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By B Yeganeh, A Sam, A Kohsari

The base of separation at Gol-e-Gohar iron ore plant (Sirjan in the south of Iran) is magnetic separation after milling. Magnetic separation in the plant is divided into two parts: dry magnetic separation and wet magnetic separation. Sixty-five per cent of the plant production belongs to the dry magnetic separator section. Therefore, investigation of this part of the plant is necessary. Prediction of plant production is one of the most important subjects in mineral processing plants. That means, before feed enters the plant, specification of production has been calculated with laboratory methods. The purpose of this paper is the prediction concentrate quality has achieved from the dry magnetic separator. The content of iron in the final dry concentrate will be predicted, with laboratory, pilot and modelling methods, before feed enters the plant. Different variables are used in this approach, which consist of: speed of the first dry magnetic separator (rougher), speed of the third dry magnetic separator (cleaner), iron content in plant feed, size of 80 per cent passing of feed, size of 20 per cent passing of feed and iron content in pilot dry magnetic separation concentrate that performs in a standard manner. The artificial neural network is used for modelling and one of its branches is the radial basis network (RBN). Iron content in magnetic separating concentrate in plant will be introduced as the target and will be calculated with the RBN method. In the RBN method, a set of data enters to neural network and they will be trained and simulated. Finally, the target will be predicted. Ultimately, the original target (actual iron content) and the predicted target (predicted iron content) compare and error of them will be calculated. The obtained result is acceptable and satisfactory.

Jan 1, 2007

By D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of a gangue mineral grade limits by the concentrator may also result in significant penalties. Online grade analysers which can provide reliable real-time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades. MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at a nickel concentrator plant. The project initially focused on stabilising the final concentrate grade without directly accounting for nickel recovery. The site later procured additional Blue Cube MQi analysers, resulting in the expansion of the FloatStar Grade-Recovery Optimiser to incorporate recovery component in the performance. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser.CITATION:Mantsho, S M, Phillpotts, D and Strobos, P, 2012. The implementation of FloatStar grade-recovery optimisation control solutions using Blue Cube online grade analysers on industrial flotation circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Grigorescu, J H. Hodgkinson

The expansive, open cut iron-ore mines in Western Australia typically experience few days of rain per annum, often amounting to less than 250 mm. Unlike mines where rainfall is frequent, they may be less prepared for extreme rainfall events. Such events can cause erosion, flooding and sedimentation, drainage alteration, spoil and stock heaps wetting and effect slope stability. Such impacts may threaten personnel safety, infrastructure, and production. The CRATER (‘Climate Related Adaptation from Terrain Evaluation Results’) framework collates and interprets a mine’s pre-existing data and semi-quantitative information to assess vulnerability to, and ultimately plan to avoid or minimise, flood-related hazard to infrastructure, people, downtime, environment and revenue. Outputs assist decision makers to design investment strategies for minimising mining operations’ vulnerability to climate. Previously developed for smaller, wetter mines in Queensland’s coal region, the outputs provide a hot-spot map, fault tree analysis and an assessment of the mine’s capacity to adapt. The multicriteria evaluation (MCE) within a geographic information system (GIS), equally suits iron-ore mines’ siteconditions (elevation, slope, drainage, soil and vegetation) to identify critical inundation areas. Hotspot results provide target zones for in-depth fault-tree analysis that, in turn, present a range of sitespecific adaptation options. Rainfall-intensity and the number of rain days since the 1970s have increased over central and eastern parts of the Pilbara Region. While tropical cyclones may become less frequent, they are projected to increase in intensity. Although some parts of the Hamersley Ranges receive more than 500 mm per annum, rainfall in the Pilbara is generally very low. Therefore, experience of the impacts of extreme rainfall events in the constantly changing topography of Western Australia’s iron ore region may be sparse. Minimising potential effects can be proactively assisted using CRATER.

Nov 8, 2021

The following paper outlines the types of employment immediately available to graduates following their university degree, a discussion on mine manager requirements, mentions career advancement and time frames to achieve this as well as providing some key information regarding student vacation work. The author hopes to educate present graduates, as well as inform students of characteristics to develop the most opportunities in life.

Jan 1, 2006

By D Flint, O Rindriatmoko

PT FreeportÆs Deep Ore Zone (DOZ) Mine is the latest block cave mine within the East Ertsberg Skarn System (EESS).Issues with undercutting and stress concentrations at the extraction level were experienced, leading to reduced pillar strength.The extraction level-related issues became more pronounced, leading to local panel drift collapse, in an area that was over 100 per cent extraction. A review of ground conditions, panel collapse descriptions, and factors contributing to panel collapse are presented in this paper.

Jan 1, 2005