Search Documents

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Shachar Magali

This article describes two new concepts regarding the CFA (Auger Cast) piles. The first one, MALI Effect, is an approach to control the casting phase, while the second one, NETA Shear, is a technique which converts the drilling rig into a geo-mechanical tool. We look upon the system of the auger and the ground as a piston inside a cylinder. When concrete (grout) is pumped into that system, an up lift force is generated (We call that force MALI Effect). That up lift force reduces the needed tension in the pull up cable. By analyzing the tension force in the cable we detect the up lift force of the concrete. That pushup force is the product of the real concrete pressure at the bottom of the auger by the area of that bottom. As the area is known, the real pressure is accurately calculated. A control loop which is based on MALI Effect is very sensitive, precise, objective, reliable and easy to be used. All the process is based on pure real physical measurements. The system has no assumptions, no comparisons, no parameters, no zeroing and no adjustments. When we penetrate into the ground like a theoretical screw, for about a meter in depth, and then brake the main cable while rotating the auger, a set of forces generates. As the auger tends to keep penetration, but the cable holds it - a tension force develops (We call that force NETA Shear). Analysis of that tension force shows that it relates to the ultimate shearing capacity of the ground.

Jan 1, 2000

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By John S. McCartney, Ismaail Ghaaowd

This study presents the results from centrifuge modeling experiments performed to understand the effects of temperature changes on the pullout capacity of scale-model energy piles embedded in normally- consolidated clay layers. The energy pile under investigation is an aluminum cylinder instrumented with internal strain gages and thermocouples, and its temperature is controlled using an internal electrical resistance heater. The energy pile was first heated until the temperature, pore water pressure, and volume change of the surrounding clay layer stabilized, after which the energy pile was cooled. Pullout tests were then performed on the energy piles heated to different temperatures to understand the effects of the preceding heating-cooling cycle on the pullout capacity. In addition, the clay undrained shear strength profiles were measured using push-pull T-bar penetration tests before and after heating. INTRODUCTION When a heat source such as an energy pile is embedded in a saturated clay layer, temperature changes will result in changes in pore water pressure as the rate of heating is typically faster than the rate of pore water drainage (Campanella & Mitchell 1968, Abuel-Naga et al. 2007, and Ghaaowd et al. 2016). Although all soils will initially expand during undrained heating, normally consolidated soils typically exhibit permanent contraction while overconsolidated soils exhibit expansion after sustained heating when drainage is allowed (Vega & McCartney 2015). Subsequent drained cooling typically leads to elastic contraction. Thermally- induced changes in pore water pressure and volume during transient heating and cooling may affect the soil- structure interaction of energy piles, as well as the ultimate capacity of the energy pile. This study is relevant as relatively few studies have been performed on the behavior of energy piles in soft clay (e.g., Ng et al. 2014), with most focused on the behavior of drilled shaft energy piles in stiff rock or overconsolidated clays (e.g., Laloui et al. 2006; Murphy et al. 2015; Wang et al. 2015; McCartney and Murphy 2017).

Jan 1, 2018

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Rick Deschamps, Brian Barkauskas, Aled Hughes, Abigail Stein

In central Washington, six miles south of the small town of Vantage, the flow of the Columbia River is harnessed by the Wanapum Dam which is part of the Priest Rapids Hydroelectric Project owned and operated by Grant County Public Utility District (GCPUD). Extending more than 8,300-feet from bank to bank, the dam includes left and right earth embankments, left and right concrete gravity sections and a 10-unit powerhouse. Adjacent to the right embankment is a concrete gravity spillway featuring radial gates measuring 50-feet-wide and nearly 70-feet-high. In the early 1960’s when Wanapum Dam was built, these seven-story spillway gates were the highest in the world. In late February 2014, 50-years into its service life, during a routine maintenance inspection, observant workers noticed a slight misalignment in the roadway deck curbs and handrails located on top of the spillway. Further survey and inspection efforts uncovered a 65-foot-long by two- inch-wide crack that spanned the full length of Monolith 4. On discovering the extent of the damage, GCPUD initiated immediate drawdown of the reservoir to relieve pressure on the spillway monoliths. Wanapum Reservoir and the areas directly downstream of the dam were immediately closed, boat ramps and inlets were left completely dry, campsites were closed and boating activity was banned on the lake until further investigations and remedial procedures were in place and completed. An extensive root cause analysis ultimately led to the conclusion that errors in the initial design calculations and late changes to the final spillway design led to a condition that generated tensile stresses in the concrete at the upstream face, which over a period of 50-years resulted in the formation of a crack along a horizontal lift joint located about 85-feet below normal pool elevation. Further analysis showed that, although visible distress was found at Monolith 4, there was nothing preventing this issue from happening at other locations along the dam spillway. Although no visible cracking was found in the other monoliths, repair procedures for Monolith 4 would have to be replicated at the remaining monoliths.

Jan 1, 2018

By Lance A. Roberts

Expansive soil formations can be found throughout the United States. When subjected to wetting, these formations have the potential to swell and exert large uplift forces on buildings and foundations. Lightly loaded structures, such as single family residences founded in areas of expansive soils, can be significantly damaged due to uplift movement from swelling actions. Designing an economical deep foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material or the use of drilled shafts can be costly. Piles made from recycled polymer materials could provide a solution. Due to a lower coefficient of friction along the interface of the soil-pile interface compared to traditional pile materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure, which minimizes the risk of significant structural damage from excessive movements. This paper presents the results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity. The remaining four piles were subjected to long-term monitoring of uplift movement during the course of the project. A concrete anchor was also installed at the test site for uplift monitoring. Data gathered during the field and laboratory testing was utilized in a non-linear soil-structure interaction model to predict the displacement behavior and internal stresses within a plastic pile and concrete anchor subjected to uplift forces from the swelling shale. While more research is needed to further understand the application for recycled plastic piles, the results from this research indicate that their use is a viable alternative for support of lightly loaded structures in expansive soil environments.

Jan 1, 2010

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002