Search Documents

By P. M. Yavorsky

Using a mine roof simulator press capable of duplicating the expected magnitude of vertical and horizontal forces experienced by underground mine roof supports, load capabilities of some roof support cribbings were measured. Comparative ultimate vertical support strengths are reported for cribs of old and new timber and nonreinforced and steel-fiber-reinforced (SFR) concrete blocks. In terms of load- bearing capability, cribs of new hickory and nonreinforced concrete blocks have about equal strength, and SFR concrete blocks are three times as strong. Wood aged 2 years underground lost 43 pct of its support strength. These data were obtained during the course of the initial familiarization exercise of the complex press.

Jan 1, 1984

By J. Andres, M. Cross

"Freeport-McMoRan’s Sierrita operations has two natural gas-fired molybdenum roasters for converting molybdenum disulfide into molybdenum trioxide. When these roasters were compared to other similar units within the company during a benchmarking exercise, it showed that increased throughput from the roaster units at Sierrita was possible. A team of site metallurgists, technical experts from other sites, and engineers from the Climax Technology Center was formed to study the potential in more detail. The team investigated many parameters in the roaster, including temperature profiles, roaster chemistry profiles, rabble and drop hole patterns, and operational strategies. The results of these studies and the associated throughput improvements are described in this paper. INTRODUCTION Molybdenum, a vital component for the steel industry, is typically found in nature as molybdenum disulfide (MoS2). MoS2 is typically recovered via flotation processes and is purified through leaching processes. While molybdenum disulfide is a commercial product, it is not the form of molybdenum that the steel industry requires. They require molybdenum in the form of molybdenum trioxide, MoO3. There are multiple ways to refine molybdenum disulfide into molybdenum trioxide. The primary method is the oxidation of molybdenum disulfide in a multiple hearth roaster. The chemistry of converting molybdenum disulfide to molybdenum trioxide is very favorable at increased temperatures, oxidizing the molybdenum through a range of exothermic reactions to ultimately produce MoO3. The chemical reactions that occur in molydenum roasting occur in three zones. These three zones correspond with four different reactions."

Jan 1, 2015

By C. A. Wiggins

The new Niagara Falls Intake Tunnel, mined in the highly fractured Lockport Dolomite, encountered prolific inflows of water contained in rock seams directly linked to the Niagara River. These inflows were pressurized and, more significantly, contained high concentrations of dissolved H2S gas. The contractors attempts to control the water/gas inflows included cement and chemical grouting from inside the tunnel. Ultimately, improving the rate of air exchange in the tunnel by increasing the fan capacity, in conjunction with a pattern down-hole pre-grouting program along the tunnel alignment allowed the contractor to control the concentration of H2S gas and complete the tunnel.

Jan 1, 1997

By Lawrence J. Connelly

During the last decade, use of freeze conditioning agents (FCA) to ease unloading and handling of both run-of-mine and washed coal during periods of cold weather has become an accepted practice by the coal industry. This paper reviews some of the mechanical means of easing the handling of coal during periods of cold weather, as well as their use in conjunction with FCA's. Factors required to promote a successful cold weather handling program are also covered. Mechanisms by which FCA's function and the influence of various substrate characteristics on the ultimate response to freeze conditioning agent performance are discussed. A modified approach to freeze conditioning is presented.

Jan 1, 1986

By Wayne Wride, Amy Lamb, Debra Sonntag

In today's "information age", we have the ability to collect volumes of data about a company's performance. The challenge is to turn that data into information employees can understand and use to fine-tune equipment, modify work processes, and ultimately manage production. Software programs have increasingly given end users control over what data is used and how it is presented. Kennecott has implemented an information system capable of collecting and storing data at the primary level. This enables plant personnel to transform historical data into information for action. Kennecott plans to expand its data collection and use trending and reporting capabilities to move toward a fully optimized operation.

Jan 1, 2000

By G. E. Mellor, R. E. Lippoth, T. B. Faddies

The Little Rocky Mountains host epithermal- gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining these oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1) mineralization; 2) oxidation; 3) structural setting; 4) lithology; 5) alteration; and ultimately, 6) the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1992

By D. M. Hausen

The role of applied mineralogy in mineral beneficiation begins with early prospect evaluation, and continues through stages of amenability testwork and pilot plant studies to the ultimate development of viable processes for mineable orebodies. After plant construction, mineral products from various locations, i.e., grinding circuits, flotation cells, gravity circuits, kilns, smelters, etc., require quick identification and control monitoring for optimum efficiency and recovery. Ore/gangue minerals are identified, quantified, and textural associations investigated by microscopic, spectrographic, and electron-optical instruments. Mineralogic analyses of large numbers of samples have required the development of sophisticated computer systems that merge analytical and mineralogic data into useful diagnostic data bases

Jan 1, 1991

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By L. Boyd, T. Martin, V. Gall

Water infiltration into subgrade infrastructure can cause major impacts on their performance. In addition to damaging the structure, water intrusion leads to deterioration of installations including electrical and mechanical components and in patron discomfort. To remedy these impacts, leak remediation is often carried out to halt water infiltration. Remediation methods include coatings, drainage, injection/stitch grouting, curtain (backside) grouting, and/or internal umbrella systems. Selection of the rehabilitation method depends on the structure’s use, owners’ priorities, its installations, structural conditions, surrounding ground, and hydrogeologic conditions. Since many factors influence the rehabilitation method chosen, a novel holistic approach is undertaken to understand leakage causes and consequences to develop the most appropriate, efficient, and reliable solution to extend the structure’s life. A reconnaissance phase combines geologic, hydrogeologic, and as-built information with detailed digital scans and visual observations to develop a database of existing conditions. This database, called a tunnelband, is used to develop the rehabilitation solution and made part of the contract documents, allowing for an informed bid by specialty contractors. Tunnelband and the preferred rehabilitation system are portrayed in contract documents, which are procured in various contract types depending on the owner’s preference and project characteristics. The pool of contractors are required to submit their understanding of this holistic approach by developing and supplying the owner with a detailed workplan. The completed rehabilitation is portrayed in detailed as-built drawings which also provide the owner with an operation and maintenance manual outlining for periodic observation of the structure and checking of its performance. Ultimately, this information is implemented into a “BIM Digital Twin” that is used by the operations and maintenance staff for long-term observations. This proposed novel framework for leak rehabilitation is currently being used successfully in a number of projects throughout the United States.

Jun 13, 2023

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024

By G. Harper

The Windy Craggy polymetallic massive sulphide deposit is located in the extreme northwest corner of British Columbia 40 miles west of the Haines Highway, 90 miles northwest of the port of Haines Alaska. The physical setting is mountainous country but with few peaks rising above 2,000 metres elevation, in contrast to the spectacular mountainous terrain to the north and south in Kluane and Glacier Bay Parks respectively. Valleys are classically U-shaped with incised V-shaped bottoms. The upper portions are still occupied by glaciers, which in the Windy Craggy area are documented as retreating at a rapid rate -in the case of the Tats Glacier of the order of 1% of its mass per year. The outcrops around Windy Craggy show a north-easterly dipping sequence of Mesozoic limey sediments and volcanics being the western limb of a north northwesterly trending syncline. Northeasterly cross folding provides a few complications. The flanks of the syncline have been buttressed by intrusive bodies of granitic affinity.

Jan 1, 1991

By R. D. Williams

INTRODUCTION In a very real sense, Butte, Montana is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site. One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot Smelter operated from 1881 to 1910 moving Upper Silver Bow Creek to the south and depositing approximately 370,000 cubic yards of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot Tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 224,000 cubic yards of contaminated material. As part of the Superfund remedy, EPA proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place which set the stage for a series of studies which continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. HISTORY OF THE PARROTT MINE AND TAILINGS Placer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery lead to a stampede of placer and lode claims. One of the first lode claims located was the “Parrot” lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow and it wasn’t until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine! The Parrott mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the District’s rich copper ore. In 1885 the employees of the Parrot Smelter bought the Butte Reduction Works, another smelter. In 1885 dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Figure 1).

Jan 1, 2019

By S. M. Robinson

Wollastonite is recognized as one of the most unique, non-metallic minerals in the world. Its history for use in industrial applications is recent compared to other minerals, however, its distinctive physical properties, such as acicular particle shape, and alkaline pH creates incorporation possibilities ranging from bowling balls to automotive fascia, from ceramic tiles to automotive brakes, and from thermal insulation board to industrial and trade sale coatings. Its future use will be impacted by the exploitation of deposits which will ensure maintenance of the acicularity and purity of this naturally occurring mineral. Additionally, closely held surface treatment technology will open up additional niches requiring highly engineered performance.

Jan 1, 1995

By P. R. Dugan

The ultimate objectives and interest in removal of sulfur from high sulfur coal include: (a) reduction of the atmospheric load that con- tributes to the problem of acid precipitation; (b) reduction of ash which contributes to decreased energy transfer in boilers and the problem of ash disposal; and (c) alleviating the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. The cost of sulfur removal in relation to the value of refined coal will govern the development of an emerging coal-refining industry. The value of refined lower sulfur coal will be influenced by the national commitment to the environment as well as economic considerations.

Jan 1, 1986

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA&apos;s in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By William Hodder, Ehsan Alavi, Muhib Hussain

Disc Cutter Wear is influenced by several geological and technical factors and excessive wear can have a major impact on the excavation efficiency of Tunnel Boring Machines (TBM). Disc cutter replacement events cause a disruption to the construction schedule and costs, and should be minimized throughout the project to the extent possible. A well-executed cutterhead inspection and maintenance plan can help mitigate abrupt cutterhead interventions and reduce its effect on project schedule and cost. This paper examines cutterhead inspection and disc cutter replacement events as well as subsequent wear data recorded in the first 7km of the 10.3 km long, 6.3 m diameter Coxwell Sanitary Bypass Tunnel (CBT) project in Toronto, Ontario. The CBT alignment is mainly through Georgian Bay Formation shale.

Dec 1, 2022