Search Documents

By K. A. McDonald

This paper will describe the experiences of Hibernia Holdings, Inc. in constructing a mineral processing facility in Mexico. It will attempt to set forth a guideline on what companies attempting to operate in Mexico can expect and what actions they can take. Ownership laws, import/export laws, labor laws, security, transportation and operating experiences will be discussed.

Jan 1, 1994

By B. Campbell

This paper will detail the successful construction methods of a 20- foot diameter wet well shaft, approximately 180 feet deep in overall depth and 150-feet below the water table, adjacent to Lake Nacimiento, in San Luis Obispo County, California. In addition to this, highlights will include the selection process in determining the most economical support of excavation, while minimizing risk of large water inflows as indicated in the Owner?s Geotechnical Baseline Report (GBR).

Jan 1, 2010

By Gary N. Greenfield

This morning, gentlemen, I should like to discuss resin anchors of a type introduced to North America approximately 2-1/2 years ago. We shall also briefly review the basics of mechanically anchored rockbolts so that a general comparison may be made. Previous efforts with synthetic resins were aimed at aiding a mechanical Or "point" anchor, obtain a better purchase in the rock mass. Resin cartridges of the type to be described in this paper are capable of achieving point anchorage or full encapsulation of mine roof or rockbolts. Of significance, therefore, is that unlike a mechanical bolt, placed and tensioned, celtite rockbolts may be fully grouted and tensioned or left untensioned in the installation sequence. Our principle effort has been to offer this system to mining and civil engineers who have encountered difficult rock conditions and wish to reinforce strata to achieve a greater degree of permanence and safety.

Jan 1, 1972

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By R. Z. Pyrih

Uranium tailings at Cotter Corporation's Canon City, Colorado Mill were moved to a double-lined impoundment, but uranium and molybdenum salts remaining in the fractured bedrock underlying the old tailings ponds seeped into groundwater. Fluor Daniel GTI recommended an in situ geochemical fixation remedy, flushing Best Sulfur Products' calcium polysulfide reductant into the subsurface with clean water. Residual metals became immobile, trapped in the bedrock. Fluor Daniel GTI designed and implemented the process on ten acres with high metal concentrations. Cotter is operating and monitoring the system, which can be expanded to "hot spots." The original remediation time was estimated at less than five years.

Jan 1, 1998

By J. Mattern

Performance monitoring, operational practices and ongoing collection of geologic data in open pit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike open pit has been ongoing since the early 1980’s, with its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls. With the proper available equipment, steepening of bench face angles via pre-split blasting is not an uncommon method for steepening of inter-ramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted resulting in quantified, rock specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2 degrees on a 300m high slope, without the necessary purchases and procedural changes that would be required for pre-split drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves. Location The Goldstrike open pit is located on the Carlin Trend gold belt in northeastern Nevada USA (Figure 1). The mine has produced over 43 million ounces (1.2M kg) of gold during the past 30 years. Engineering Geology Stratigraphy Figure 2 is a stratigraphic section of the rocks in the Goldstrike open pit. Quaternary alluvium and Miocene materials typically are poorly indurated stiff soils and are not present in all locations. Bedrock units consist of siltstones, mudstones, sandstones and cherts. From top down the major units exposed in the open pit are the Vinini Formation, the Rodeo Creek Unit, and the Popovich Formation. In general, rock mass strength increases with depth.

Jan 1, 2019

By Craig M. Sams

Dry grinding circuits and factors influencing the selection of the most appropriate grinding system for a given ore selection are discussed. Comparisons of the drying, grindability, installed costs and operating costs are presented for several grinding systems.

Jan 1, 1994

Not quite a year ago, during a speech to a group of mining professionals in Washington, DC, the subject centered around the long-range importance of conducting research projects and how much that research needs to specifically apply to health and safety matters in our industry. The point was made about the critical need to work together with government, private industry, labor organizations and academia speaking with a unified voice as we all march into the future together. The fundamental benefits of competitive research were mentioned --to improve our quality of life, to develop our energy resources, to achieve a safe and healthy environment and to ensure long-term economic growth. Very importantly, emphasis was given to the natural link that makes my agency, the Mine Safety and Health Administration, and the National Institute for Occupational Safety and Health --NIOSH --the beneficiaries of each other's findings. Unquestionably, there are lines of separation. The main responsibility of the agency I represent, MSHA, is enforcement of the nation's mine safety and health laws. But we also have an additional responsibility and that is to coordinate and give priority to research in a never-ending hunt for answers.

Jan 1, 1999

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010

By Goutam H. Shahani

The current economic downturn has been at the center of media attention for several years. Today, the mining and mineral sectors are being impacted by highly fluctuating supply-and-demand conditions, extreme price volatility and tremendous market uncertainty on a world-wide basis. There have been numerous plant closings, project cancellations and employee layoffs. In this gloomy economic environment, it is easy to forget that the world?s gross domestic product (GDP) has more than doubled in real terms during the last 30 years. While current market turbulence may continue for some time, the long-term trend is unmistakably upward. Living standards are rising all over the world, thereby creating demand for food, clothing, transportation and housing. This translates into tremendous demand for the mining and mineral sectors. In the future, new capacity and plant expansions will be necessary to meet this need. These investments, which typically have a life span of 30-plus years, will have to be based on long-term economic considerations rather than current market conditions.

Jan 1, 2011

NICOR Mineral Ventures, Inc. retained Neyer, Tiseo and Hindo, Ltd. to evaluate the potential effects of a planned dewatering operation at NICOR's proposed, 258-acre silica sand mining facility near South Rockwood, Michigan. The ?orebody? is a horizontally extensive, friable, quartz sandstone from the Sylvania Formation which also serves as an aquifer for some of the rural, residential development near the site. We conducted an aquifer test on the site which identified the important aquifer properties. Using these data and an analytical model, we determined that the radius of influence would be expected to range up to 6000 feet from the quarry during its final development stage. An inventory of water supply wells revealed that most wells had sufficient available drawdown and would not be adversely affected. A long-term groundwater monitoring program was recommended to monitor the possible effects at some of the closest wells.

Jan 1, 1987

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By William Gleason

For the first time in many years, the Liebherr Group chose to host its annual conference for the international construction trade press in the United States. The reason for the move is simple ? mining. Like other large corporations, especially those in the construction fields, Liebherr felt the effects of the global economic crisis that began in 2008. The slowdown in the housing market was especially hard on Liebherr?s mobile crane and earth moving divisions. The mining division, however, while affected by crashing commodity prices that led to cancelled orders and the loss of financing for some customers, was not battered as badly as the other divisions. And now, with the price of commodities once again on the rise, it seems that it will be Liebherr?s largest machines that lead the family-owned company to better days. ?We can report that our generally optimistic view during the crisis has proved adequate,? said Joachim Janka, president of Liebherr mining equipment, at the conference in Williamsburg, VA, just down the road from the company?s mining truck division global headquarters in Newport News, VA. ?Since the third quarter of 2009, our mining equipment activities have been recording once more a strong and steady demand. This has already yielded a substantial increase in market shares for our product lines of large mining shovels as well as for mining trucks.?

Jan 1, 2011

By W. A. Wilkinson

Mine planners are under pressure to evaluate the impact of changing economic times and newly acquired data on their mine plans. Incorporating changes such as commodity prices, customer sales, fluctuating cost assumptions and newly acquired geologic data requires quick turnaround for model building and planning to keep mine plans on pace with changes as they occur. Because of the length of time required to perform some of the geologic modeling and mine planning tasks, planning frequency may not be keeping pace with the frequency of change. To meet these challenges, one leading North American mining company successfully increased the frequency rate and accuracy of its mine plans to stay current with incoming data, ensuring its mine plans reflect the latest information, thereby minimizing or eliminating production cost variance.

Jan 1, 2010

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By Marc Carriere

Bright-orange couplings adorning piping systems are a common sight in just about every underground mine in North America. Grooved mechanical piping, the pipe-joining system that utilizes these couplings, is the preferred method for joining underground and plant piping systems in the mining industry, due to the ease and speed of installation and maintenance. However, the applications for such systems have traditionally excluded high-pressure systems. Most grooved mechanical couplings have a moderate working-pressure limitation, so high-pressure systems have required the use of alternative joining methods, typically heavy-duty flanges. However, the introduction of high-pressure couplings (up to 4,000 psi) has made the grooved joining method viable, and even preferable, for backfill, deep-mine chilled water and dewatering lines and other high-pressure piping applications. As engineers explore the use of high-pressure couplings, questions will undoubtedly arise about the joining method?s capabilities. This article will address the capabilities and specifications of high-pressure couplings, and compare flanged and grooved mechanical pipe joining in traditional as well as high-pressure underground mining applications.

Jan 1, 2011

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By G. P. Larson

We define a specialized mineral market as follows: Specialized Markets are markets where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach compared to bulk or commodity markets for traditional minerals. Specialized and commodity markets are differentiated by several characteristics as listed in Table 1.

Jan 1, 1990

By D. W. Jahn

Road construction in the near future will require contractors to guarantee that a project will remain trouble free for years after the project has been completed. These guarantees will challenge aggregate producers to become technically proficient in judging performance of their products. Testing procedures are described that may be used to predict performance of concrete and asphalt pavements before being committed into a construction project, and may also be used as quality assurance tools during construction to monitor performance as construction proceeds.

Jan 1, 1995