Search Documents

By Paulo de Tarso Rossi Haddad, Eric Valmir Spósito, Cristiane Sales Gonçalves

The heat treatment is a process that acts as a key factor in the tool life of tools made with hot work tool steels. Due to their applications, the main desirable metallurgical properties of this material class are toughness and hot resistance, without which the tools may suffer premature failure, and may lead to increases in the cost of producing articles made using such tools [1, 2]. Therefore, special attention must be given to the heat treatments practiced in these steels, whose operations involve quenching and tempering. The present work carried out the effects of the austenitizing and tempering temperatures on the microstructural condition, hardness and impact properties of TENAX300IM®, modified AISI H11 with lower silicon content. Hardness was measured by the Rockwell method, C scale; the toughness was evaluated by the Charpy-V impact test; and the microstructure for each condition was evaluated by optic microscopy. It was shown that higher austenitization temperatures resulted in increased grain size and hardness; higher tempering temperatures resulted in reduction of hardness, and secondary hardening peaks were observed for some austenitization conditions. The impact resistance showed an inverse behavior to that of the hardness, remaining initially constant, up to ~ 550 ° C of tempering temperature, and then increasing with the tempering temperature. The microstructures presented great dissimilarity, mainly due to the dissolution of carbon and alloying elements in the matrix.

Nov 22, 2018

By Leandro Seixas Bicalho, Raphael Alcantara da Costa, Pedro Martins de Almeida Rollo, Eduardo Tres, Anderson D. Thomazini

Usual pelletizing process requires the use of iron ore within a given range of particle size. The pelletizing plants often have comminution circuits composed of ball mills and roller presses to meet the granulometric parameters. Aiming at the partial removal of grinding operations and elimination of wet ore processing, the present study evaluated the pelletizing of two samples of ore with lower surface area: (1) sample with only one passage into the roller press (specific surface area of 997 cm²/g) and (2) “in natura” sample as fed to the pelletizing plant (specific surface area of 450 cm²/g). These experiments were conducted with the use of bentonite and the products E/PE MIN 070/19 and E/PE MIN 090/19, made available by Clariant for this purpose. The results indicated that conventional bentonite is not efficient for coarse particle agglomeration. On the other hand, the products E/PE MIN 070/19 and E/PE MIN 090/19 achieved good performance. Considering a sample with only one passage into the roller press it was possible to form pellets similar to those produced in the conventional process.

Oct 1, 2019

By João Batista Ribeiro Martins, Érica Simões Rodrigues, Ramiro da Conceição do Nascimento Júnior, Marcos Tadeu D’Azeredo Orlando

In order to guarantee the quality of the sinter and process control some measurements are made such as RDI and FeO (Fe2+). However, the behavior of sinter during reduction in the blast furnace is not always understood, when it is analyzed only metallurgical, physical and chemical quality. Therefore, it is necessary to find alternative techniques to understand more this behavior. In this work four experimental trials were performed to obtain sinter samples with different FeO (Fe2+) contents. Optical microscopy was performed to identify and quantify the phases in sinter and to evaluate the magnetic behavior of each one, the Magnetic Susceptibility technique was used. The results obtained between Optical Microscopy, Magnetic Susceptibility and quality parameters were compared and then was identified that Magnetic Susceptibility may be an alternative to help the understanding of sinter behavior in Blast Furnace.

Oct 1, 2019

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By Elen Mancini Santi Paulettor, Vinicius Calheiros, Eduardo de Oliveira Cabral

At this paper, Eirich will present its new tool for sinter analysis integrated to the sintering control system. For stabilization and optimal, continuous control of the sintering process, QualiMaster MT1, a device was developed which guarantees fully automatic representative sampling and material analysis and thus a high and stable sintering quality. Mining tailings often has a considerable proportion of valuable substances. In addition to this work, we will also present our mixing technology that allows the economic recovery of these mining tailings.

Oct 1, 2019

By Geovane Viturino da Silva, Jeziel de Melo Canedo, André Wulff Hirano, Maxwell Pereira Cangani, Luiz Henrique Curado Ribeiro

With the deterioration of the quality of the iron ore, the new conditions of quality of the raw materials (mainly sinter feed) were adapted to their processes, resulting in the need for changes in the chemical quality of the sinter for blast furnaces in the Ternium Brazil, without changing the parameters of chemical, physical and metallurgical quality. Due to the change in this scenario, there was a great impact on the quality of the fine iron ore this year in 2019, due to which the work ranges of sinter MgO and B2 were currently modified to minimize these impacts in the blast furnaces of Ternium Brazil. This work aims to minimize the effects of the sinter worsening, with the reduction of the sinter MgO and B2 bands, with an increase of 2% in the mixture yield and FeT elevation in the range of 1.6% in the sinter product.

Oct 1, 2019

By Bruno Sampaio Jannuzzi, Klayton Sebastião Leopoldino, Rodrigo Jorge dos Santos Arruda, Sergio da Cunha Motta

Devido à necessidade de mitigar os riscos aos quais os empregados próprios e contratados ficavam expostos, durante o processo de peação de bobinas, em porões de navios, e também de reduzirmos os custos nessa operação, concluímos que deveríamos alterar o processo para aumentar a segurança dos trabalhadores, com a eliminação de materiais perfurocortantes, gerar redução do esforço físico, com a substituição de equipamentos e, consequentemente, obter redução de custos e ganho de produtividade, no embarque de bobinas de aço, em porões de navios, no Sepetiba Tecon - Porto de Itaguaí.

Oct 1, 2019

By M. A. Mekicha, M. B. de Rooij, C. Pelletier, D. T. A. Matthews

One of the main factors that reduce strip cleanliness are iron fines, which are formed due to the abrasive interactions of the roll surface and the strip in the roll bite during cold rolling. They can cause a problem in fouling of the cold rolling mill as well as downstream processes. It has been repeatedly observed that chrome plating the work roll improves strip cleanliness. In the present work, scratch tests and reciprocating sliding tests were carried out under lubricated conditions to explore the influence of chrome plating on iron fines formation. Scratch tests were conducted to study the influence of chrome plating on iron fines formation at single asperity scale due to its intrinsic property. Reciprocating sliding tests were performed to study the influence of chrome plating a rough surface on iron fines formation, taking into account the initial roughness. The scratches made using chrome plated pins showed lower friction, generated less iron fines and exhibited lower material transfer. Reciprocating sliding tests done using the uncoated pins showed galling at different sliding distances depending on the roughness of the pin. On the contrary, reciprocating sliding tests with the chrome plated pins exhibited no galling irrespective of the roughness.

Oct 1, 2019

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz, Thiago Soares Lima, Rafael Kakitani

Materiais de interface térmica (Thermal Interface Materials - TIMs) são responsáveis pela troca térmica entre a fonte geradora de calor do processador integrado e o dissipador de calor. Devido ao seu baixo ponto de fusão, boa fluidez e cumprimento com as exigências de regulamentação (Restriction of Hazardous Substances - RoHS), ligas à base de bismuto têm sido investigadas para aplicação como TIMs de alta performance. Neste contexto, a análise das propriedades dessas ligas em função de parâmetros microestruturais torna-se, portanto, de elevado interesse científico e tecnológico para o setor eletrônico. Assim, este trabalho tem como objetivo desenvolver correlações entre propriedades de resistência à tração e a microestrutura da liga Bi-0,28%Ni solidificada sob um intervalo de taxas de resfriamento usualmente obtido em processos industriais. Por meio de microscopias óptica e eletrônica de varredura foi observada uma morfologia tipicamente eutética lamelar, composta por lamelas ricas em bismuto com o intermetálico Bi3Ni nos contornos. Os espaçamentos lamelares (λL) foram, então, correlacionados com os parâmetros térmicos de solidificação, sendo propostas leis experimentais de crescimento microestrutural. Ao fim, observou-se que, para λL < 101 μm, equações do tipo Hall-Petch caracterizam a variação do limite de resistência à tração e do limite de escoamento.

Oct 1, 2019

By Klaydison Silva, Maurício Curi Segato, Elves Matiolo, Neymayer Pereira Lima

Flotation is the main concentration process, has been applied with sucess for the removal of quartz on the iron ore industry aiming high quality concentrates. limiting the top size close to 0,300mm and the removal of slimes are fundamental for the efficiency of reverse flotation of quartz. The high consumption of reagents, leading to insufficient particle coverage, and increased foam stability, leading to the difficulty of removal of quartz particles, are the main deleterious effects of the presence of slimes. Recent characterization studies, together with the development of new collector of linear chain, allowed the obtaining of concentrate with SiO2 contents close to 3% with 94% of metallurgical recovery, based on pilot tests carried out on a sample flotation column of the Quadrilátero Ferrífero.

Oct 3, 2019

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By Felipe da Silva Siqueira, Weslley Luiz da Silva Assis, Camila dos Santos Pinto, André Luiz Moraes Alves, Guilherme Dias da Fonseca, Paulo Rangel Rios

Neste trabalho estudou-se o comportamento cinético das transformações de fases por nucleação e crescimento nas interfaces (faces, arestas e vértices), das matrizes poliedricas de Kelvin, Voronoi e de Monte Carlo, através da simulação computacional. Com o objetivo principal de comparar os resultados obtidos das simulações com os modelos analíticos de Johnson e Mehl, Kolmogorov e Avrami (JMAK), e de John W. Cahn. As matrizes foram geradas por modelos estocásticos e através do método de crescimento do Cone Causal. Em engenharia o entendimento do comportamento das transformações de fases por nucleação e crescimento são importantes para prever os possíveis locais de nucleação, assim como no entendimento do comportamento dos constituintes presentes do diagrama ferro carbono, na decomposição da austenita, no processo de recristalização, entre outros. Desta forma, o modelamento computacional foi utilizado para o estudo das transformações de fases por nucleação e crescimento, obtendo como resultados a fração volumétrica, o caminho microestrutural e a contiguidade, ambos resultados foram importantes para a caracterização microestrutural e para descrever a distribuição dos núcleos no espaço. Com os resultados obtidos observou-se que se os núcleos estão bem distribuídos nas interfaces o impingement será mais fraco, levando as simulações de Voronoi e de Kelvin a corroborarem com o modelo analítico de JMAK, já o Modelo de Monte Carlo, não apresentou o mesmo comportamento, ou seja, ficou evidenciado que nem sempre a aleatoriedade vai ser válida para todos os casos. Foi constatado também que se aumenta consideravelmente a quantidade de núcleos, a distribuição perde a característica de aleatoriedade e passa a se comportar como clusters, corroborando com o modelo analítico de Cahn.

Nov 10, 2019

By Janaina Goncalves Maria Da Silva Machado, Francisco Carlos Gomes da Silva Junior, Stephany Aparecida Santos da Mata, Walney Silva Araújo, Matheus Souza Rodrigues

O aço inoxidável duplex (AID) ASTM 890 de grau 3A tem grande utilização na indústria de tubulações de petróleo no Brasil e no mundo. O estudo da variação do tempo necessário para solubilizar um material é importante, pois, diminuindo esse tempo, pode ser reduzido gastos com forno. O objetivo desse trabalho é comparar diferentes resultados para três tempos distintos de solubilização do aço inoxidável duplex fundido ASTM 890 de grau 3A. A literatura indica que a solubilização desse aço deve ocorrer na temperatura de 1120°C, no período de 4 horas. Entretanto, não existem trabalhos que mostrem a influência da diminuição do tempo do tratamento térmico na resistência á corrosão desse material. A fim de analisar isso, foram feitos trés tratamentos térmicos a 1120°C, em tempos 30 minutos, 2 horas e 4 horas. O grau 3A tem como característica, por exemplo, não conter cobre em sua composição, ter 1%p Mn e ter também 25%p Cr. Para tal estudo foi feito uma análise microestrutural em microscópio ótico para observar diferenças nas fases do material. Em seguida, foi usado ensaios eletroquímicos de monitoramento de potencial de circuito aberto, espectroscopia de impedância e polarização pontenciodinâmica anódica, utilizando um eletrólito de NaCl 1M, para ver o desempenho contra a corrosão nessa liga. Também foi feita uma avaliação mecânica do aço sendo exposto a testes de microdureza. Por fim, foi obtido, com esses resultados, pouca mudança significativa no comportamento do material após diferentes tempos.

Mar 1, 2019

By Willy Ank de Morais, Márcio de Morais Tavares, Mateus Araújo e Silva, Érika Elis Kuo, Cícero Lopes de Souza

Estruturas de aço são utilizadas em diversas aplicações na construção civil, com vantagens relativas a outros tipos de construções, tais como leveza e rapidez na execução da obra. Porém um dos maiores problemas neste tipo de sistema construtivo é a corrosão atmosférica a que estará sujeita o aço estrutural utilizado. Com o objetivo de se avaliar a resistência à corrosão atmosférica, neste trabalho, foram construídos painéis expositores, conforme a NBR 6209, para manter corpos de prova de aço estrutural comum e patinável, por um período inicial de setenta dias em dois locais distintos, categorizados com de agressividade ambiental I e III, respectivamente interior e litoral do estado de São Paulo. Superficialmente o processo de degradação foi nitidamente diferenciado, com o mesmo resultado sendo apontado pela alteração da massa das amostras, que se elevou durante a exposição ao ambiente de agressividade III, já que os produtos de corrosão formados não se desprenderam no curto período de tempo do teste. Mesmo considerado que a norma estipula um tempo mínimo de dois anos de duração para o ensaio, que ainda está em andamento, o presente estudo aponta a necessidade de adotar mecanismos de proteção contra a corrosão muito mais severos nas regiões litorâneas.

Mar 1, 2019

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019

By Norbert Asamer, Stefan Purrer

Depending on the product or the material grade, conventional deburring machines, such as e.g. with rotating hammers, are in many cases not capable to reliably or completely remove burrs from the edges of a continuously cast product. Burr, however, is generated at the front and/or tail ends of a slab, bloom or billet as a result from torch cutting. Likewise, traversal grinding of the slab’s rolling surfaces can also cause burr at the long side edges of the slab whereby such burr can even be more difficult to remove. Based on their experience and know-how with abrasive machining processes (abrasive cutting, high-pressure grinding) over a period of more than 50 years up to now, BRAUN has developed a highly flexible deburring grinding machine for applications which are too difficult for conventional deburring techniques. BRAUN’s deburring grinding machines were successfully introduced to the steel industry and have proven their worth under normal production conditions already. The subject paper describes the key features and advantages of BRAUN’s machine design and the operational results from the first already completed projects.

Oct 1, 2019

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019