Search Documents

By Charles C. Rodd

PRIOR to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (1) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types of tests are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. IN the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce" was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equipment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction set-up, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators were beginning to suspect that the high rates of production maintained during "potential" tests were conducive to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term "productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1942

By Charles Barrett

THE orientation of metal crystals and grains, both large and small,. can be determined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satis-factory in the laboratory the reflection of light from crystallographic etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographic projection is used to facilitate handling the data, this note may be considered as an appendix to an earlier review of the metallurgical uses of the stereographic projection.1 Various methods involving etch pits have been used by other investi-gators, Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4), holding it at arm's length, and marking a spot on it when it has been turned so that the etch pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2° and is extremely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czoehralski, 5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers"' developed a method for estimating the number of grains in a polycrystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and recrystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereo-

Jan 1, 1940

By Alden Greninger

MANY recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces-other than the unknown "plane of polish"; hence resort must be had to other means of determin-ing orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for. accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.1 The methods that, have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods-2

Jan 1, 1934

By Newell Hamilton

SOME years ago, in the manufacture of seamless tubing from an alloy steel containing 0.07 per cent maximum carbon, 18 per cent chromium and 8 per cent nickel, at the plant of The Babcock & Wilcox Tube Co., a peculiar type of piercing defect was noticed. This defect was definitely associated with certain heats of the alloy and was independent of any of the variables of mill operation and billet-heating condition. A thorough analysis of the defective material yielded but one clue to the reason for its abnormal behavior in piercing and that was its oxygen content as determined by the vacuum fusion method. The oxygen content of the defective 18-8 alloy was found to be from two to three times that of the material that had pierced satisfactorily, and this incited an active interest in the vacuum fusion method for the analysis of alloy steels. After a critical survey of the literature on this subject, and considerable experimentation, an apparatus and technique were evolved that gave a fairly rapid, simple and reliable method of analysis. Samples selected from six years of tube production of 18-8 and other corrosion-resistant alloys were analyzed by this method. This paper describes the procedure and gives a correlation of the oxygen, hydrogen and nitrogen contents of a number of alloy steel samples repre-sentative of good and bad tube-piercing quality.

Jan 1, 1934

By J. G. Thompson

OXYGEN, nitrogen and hydrogen are present in' practically all metals in one or more of the following forms: (1) molecular gas in blowholes or blisters, (2) combined in nonmetallic inclusions such as nitrides, oxides or silicates, and (3) in solid solution in the metal. Gaseous elements, in some of these forms, are encountered in practically all metals and alloys but possibly have received most publicity in connection with iron and steel. In fact, the entire steel industry depends upon the control of the oxygen content during the refining process, as well as in the finished material, and it was only after the adoption of the use of efficient deoxi-dizers such as manganese that the production of good steel with a low carbon content became possible. In normally clean, sound steel the amount of hydrogen is negligible and the amounts of oxygen and nitrogen vary from a few thousandths to a few hundredths per cent. However, many of the effects attributed(27,31,40,41,53,54,55.56,62) ? to the presence of these elements are important and at first glance appear to be out of proportion to the amounts of impurities involved. The presence of oxygen is believed to affect the solubility of carbon in austenite and ferrite and thereby to affect the structure of the iron or steel. Such properties as strength, hardness, ductility, elastic .limit, impact resistance, magnetic permeability, tendency toward caustic embrittlement, irregularity in carburization, the cutting life of, tools, certain corrosion phenomena, the presence of flakes, seams, bands, ghost lines and hair cracks, and the tendency to age-harden, all have been attributed to the presence of oxygen.

Jan 1, 1932

By J. G. Thompson

OXYGEN, nitrogen and hydrogen are present in practically all metals in one or more of the following forms: (1) molecular gas in blowholes or blisters, (2) combined in nonmetallic inclusions such as nitrides, oxides or silicates, and (3) in solid solution in the metal. Gaseous elements, in some of these forms, are encountered in practically all metals and alloys but possibly have received most publicity in connection with iron and steel. In fact, the entire steel industry depends upon the control of the oxygen content during the refining process, as well as in the finished material, and it was only after the adoption of the use of efficient deoxidizers such as manganese that the production of good steel with a low carbon content became possible. In normally clean, sound steel the amount of hydrogen is negligible and the amounts of oxygen and nitrogen vary from a few thousandths to a few hundredths per cent. However, many of the effects attributed(27,31,40.41,53,54,55,56,62) ? to the presence of these elements are important and at first glance appear to be out of proportion to the amounts of impurities involved. The presence of oxygen is believed to affect the solubility of carbon in austenite and ferrite and thereby to affect the structure of the iron or steel. Such properties as strength, hardness, ductility, elastic limit, impact resistance, magnetic permeability, tendency toward caustic embrittlement, irregularity in carburization, the cutting life of tools, certain corrosion phenomena, the presence of flakes, seams, bands, ghost lines and hair cracks, and the tendency to age-harden, all have been attributed to the presence of oxygen.

Jan 1, 1932

By H. J. O’Donnell, B. C. Parks

IN 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen's terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.l The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O'Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogenation properties of certain American coals. In the years following adoption of Thiessen's method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau's method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O'Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring instrumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. PETROGRAPHIC COMPONENTS AND TYPE CLASSIFICATION OF COAL Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1948

By Andrew A. Blair

THE increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

Jan 1, 1876

By A. F. Melcher

THE present paper is a progress report. on an investigation of the physical factors of oil and gas and especially of their sands, I such as-pore space, size of pores or permeability, retentivity, viscosity of the oil, temperature, pressure, thickness and area of the pay sand, water relations, and capillarity. The purpose is to determine as many of these physical factors as possible, and to ascertain the relations existing, directly or indirectly, between these physical factors and the production of oil and gas. As yet only pore space2 and size of grains of pay sands have, been investigated, although an apparatus has been designed to determine the permeability of a sand to oil, water, or gas under definite drops of pressure between the entrance face and exit face of the sample. Messrs. E. W. Shaw, R. Van A. Mills, D. Dale Condit, G. B. Richardson, G. C. Matson, and C. H. Wegemann collected the samples upon which the physical determinations were made. Acknowledgment is made to my colleagues of the United States Geological Survey for many suggestions and criticisms; to Mr. Mills for the production data given of the oil wells from which some of the samples were collected; to Mr. A. W. McCoy of the Empire Gas and Fuel Co., Bartlesville, Okla., for many ideas.

Jan 4, 1920

By R. W. Smith

A study has been made of the crushing and grinding circuits by the Portland Cement Association in nine cement plants. Five of the plants used the wet process and four, the dry method. Both raw and clinker grinding were studied in the four dry processing plants. The raw materials used varied considerably from plant to plant. Actual power consumption data were obtained for the majority of the grinding mills in these plants. Previously representative raw and clinker samples had been obtained from the nine plants, and Bond1 and Hardgrove2 grindability tests were run on these samples. All pertinent data concerning the grinding mills, such as mill size and speed, ball charge size and weight, size distribution of feed, and discharge materials were also obtained. Thus it became possible to calculate the actual horsepower used by the various mills, and to compare this figure to the theoretical horsepower as calculated by several different methods.

Jan 4, 1961

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By V. E. Christensen

AT most smelting plants, forced draft, induced by high stacks or fans, is used to carry the gases away from the furnaces, roasters, or sintering plants. Gases moving under forced draft carry varying amounts of solids in the form of dust and fume. Where the weight of the solids is material, and the metal content high, it is usually profitable to treat the gases to recover these solids. Baghouses, Cottrell treaters, and settling chambers are the common forms of plants used to recover solids from gases. To check on the efficiency of these plants it is necessary to know the volume of gas leaving the plant and the amount of solids carried by the gas. As the volume of gas is equal to the product of the velocity of that gas and the cross-sectional area of the flue, the determination of the volume includes the measurement of the area of the cross section and the determination of the velocity. The velocity is generally measured by means of the Pitot tube and Ellison differential pressure gage, although low velocities are best determined by means of an anemometer. The dust concentration is determined by passing a measured volume of sample through a filter and weighing the dust caught. From this the dust concentration per unit of volume may be calculated. It is necessary to assume that the gas is homogeneous or that each cubic foot of the gas contains the same weight of dust as every other cubic foot. Having the volume of gas passing through a flue per unit of time, and the dust concentration of the gas per unit of volume, the amount of solids may easily be calculated.

Jan 1, 1935

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By Barry H. G. Brady

A state of stable equilibrium is required in a mine structure to ensure that small increases in the mined void are accompanied by only small displacements of the rock mass. Methods of determining the stability of equilibrium in a rock mass currently require a geometrically regular stoping layout, and introduce a number of simplifying assumptions. The method reported in this paper models the mine near-field using Finite Elements, and the far-field using Boundary Elements. The stability of equilibrium in the modelled structure can be assessed directly from the value of selected principal minors of the global stiffness matrix.

Jan 1, 1981

By E. P. Polushkin

The object of this paper as to show that the structural composition of an alloy may be found by the planimetric measurement of the total area occupied by each of the constituents on a few representative photomicrographs of this alloy. When the area is determined the volume and the proportional weight of the constituent may be calculated. This method has been used for the determination of the structural composition of binary eutectics and other binary alloys with known constituents; also the composition of unknown constituents in binary alloys. The accuracy of the method is. high enough to justify its application to metallographic problems instead of the chemical analysis. THIS work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that 'the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility, of determining the amount of the constituents with-out separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. DESCRIPTION OF PLANIMETER Suppose Fig. 1 represents a part of a photomicro-graph on which the total area of the black figures is FIG. 1?-PART OF PHOTOMICROGRAPH ON WHICH TOTAL AREA OF BLACK FIG- URES IS TO BE FOUND. to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively.

Jan 12, 1924

By Philip Drinker

IN THE mining and metallurgical industries, numerous problems arise requiring determinations of solid and of liquid particles suspended in air. Frequently, these problems are of local interest and involve purely economic or operating difficulties; on the other hand, toxic effects from the inhalation or the ingestion of substances suspended in air may be a matter of concern. For checking up process improvements or for determining ventilation efficiencies in problems of this general nature, various methods have been proposed. Although simpler methods are often satisfactory, precipitation combines several desirable features that other methods lack. This paper is, therefore, devoted to a discussion of portable alternating-current precipitators applicable to the quantitative determination and microscopy of dusts, fumes, and smokes in air. Small particles suspended in gases, such as air, are referred to in the literature as aerosols or suspensoids. Of these terms, suspensoids appears to be preferable as being more nearly in keeping with words in everyday use. In problems involving air pollution by small, particles-by suspensoids-it is convenient to distinguish three broad classes based on the size, the degree of dispersion, and the method by which the particles become suspended in the air. Dusts.-Particles or aggregates of particles, 150 to 1 micron in diameter, that are thrown into the air by mechanical agencies are termed dusts. Examples are silica, talc, cement, organic dusts such as hard rubber, starch, and cocoa; flocculated fume and smoke products. Fumes.-Particles, 0.2 to 1 micron in diameter, formed from chemical or physicochemical reactions are known as fumes. Examples are ammonium chloride, lead and mercury, zinc and magnesium oxides, fogs, and acid mists.

Jan 3, 1925

By Edgar Stansfield

WHEN plants decay in a peat bog the woody parts form a brown pasty mass, or peat muck, largely soluble in. alkalis. This brown matter has been termed "ulmin." The same material, but commonly black in color, is found in coal, and there is evidence of the similarity between the material forming the main bulk of the coal and the bulk of the more recently decayed material in peat bogs. The. more recent or low-rank coals, such as lignite, little removed from the peat stage, contain notable percentages of alkali-soluble ulmins, but the percentage decreases with increased, degree of coalification and is negligible in bituminous or higher rank coals. The determination of the alkali-soluble ulmins in any coal gives, therefore, an indication, of its degree of coalification or rank. Coals which contain few or no ulmins soluble in alkalis do contain ulmins which can be rendered soluble by oxidation. The higher the rank of the coal, the more difficult it is to oxidize the insoluble ulmins and make them soluble. High-rank coals can be differentiated by oxidation tests on the, insoluble ulmins; but low-rank coals can be characterized by both their soluble and insoluble ulmins. This paper deals with the determination and significance of the alkali-soluble ulmins, present, as such in- the coal. The chemical nature and composition of ulmins are not discussed.

Jan 1, 1932

By O. Lietard, J. Yvon, R. Mercier, J. F. Delon, J. M. Cases

INTRODUCTION Fineness is one of the main characteristics of powders and this parameter is the object of several definitions based on criteria connected with their uses as well as their determination methods. In trying to obtain the best reaction surface, fineness is characterized by the determination of the specific surface, but in other cases, particle size analysis is used. These two main methods are not, in fact, entirely independent and their complementary nature provides information concerning the morphology of the particles. In the case of a product formed by isodimensional spheres, the relationship between the specific surface and the diameter is well known: [S = 6 spd] where p is the specific weight of the material and d the diameter of the spheres. With no monodimensional spheres, but rather a granulometric distribution whose occurrences follow a mathematical law (1), the relationship is more complicated. The relationship between the specific surface measured by gas adsorption and the data of the particle size analysis is much more difficult to predict in the case of asymmetric porous particles, whose particle size distribution curves do not correspond to a known statistical law.

Jan 1, 1980

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By Fred C., Bond

DETERMINATIONS of circulating load in a classifier operating in closed circuit with a grinding mill are usually made from screen analyses of the mill feed and classifier products. The percentage remaining on someone selected screen size must be used in the calculation, and, because of the wide variation in average particle size between the mill feed and classifier overflow, an accurate and representative result at the selected mesh is often difficult to obtain. To overcome this difficulty and reduce the time required in making the determination, I have devised a method which uses the liquid-solid relationship in the circuit rather than screen analyses. The quantities required for the calculation include only the usual dilution and feed tonnage measurements, which should be made regularly in the course of ordinary mill operation and, in addition, the amount of new water added to the classifier, or to the head of the mill with the new feed. If measurements are obtained on both of these quantities it is possible to check the calculated circulating load, and to calculate the percentage of moisture in the new feed to the mill; or, if the latter is known, to check the feed tonnage.

Jan 1, 1937