Search Documents

By Harvey P. Knudsen, Young C. Kim

This paper illustrates the application of geostatistics to a roll front type uranium deposit located in Wyoming. The steps involved in calculation of experimental variograms, variogram modeling, and verification of the resulting models are described in detail. The resulting spherical variogram models for grade thickness and thickness show strong geometrical anisotropies. The major axis of anisotropy for both variables is approximately parallel to the axis of the roll front and the minor axis perpendicular to the roll. This model confirms the technique of drilling "fences" across the roll front, where the drilling is much closer together than the fences along the roll.

Jan 8, 1979

By Richard D. Call

Data obtained from development drilling provide the basic input for open pit mine planning and design. Development drilling is defined as delineation of the size, mineral content, and disposition of an ore body by drilling boreholes (Thrush, 1968). The objectives of development drilling are: ( 1 ) determining the geometry of the mineralization, ( 2 ) determining the grade and tonnage, , ( 3 ) obtaining samples for metallurgical testing, and ( 4 ) obtaining geotechnical data for mine design. To accomplish these objectives, an appropriate drilling plan must include the number of holes, the spacing and orientation of the holes, and a suitable data collection program. The data collection program covers sample collection, hole logging, and data presentation. This chapter will present some guidelines for development drilling and data collection techniques. The operational aspects of drilling will be covered in an- other chapter.

Jan 1, 1979

By Glenn C. Waterman, Scott Hazen

3.1-1. Purpose. Development drilling is directed towards determining the grade, volume, and three-dimensional outline of a mineralized zone previously located by exploration. It is distinguished from exploration or reconnaissance drilling, which has as an objective the discovery of new mineralized areas. A development drilling and bulk sampling program should furnish the following information: 1. Geology of the mineralized zone. 2. Quantitative data on grade and tons of material within pertinent cutoff limits. 3. Physical size and shape of the deposit. Areas underlain by waste as well as ore. 4. Mineralogica1 and metallurgical characteristics of the ore. 5. I1hysical characteristics of the ore. 6. Hulk samples for metallurgical testing and grade check. 7. Data on other factors that could affect mining operations, such as ground water, ground conditions, etc. 3.1-2. Procedures. There are numerous methods and techniques that are used to acquire pertinent data on a potential ore deposit. The total cost and accuracy of a development program depends on significant evaluation of the geology, proper selection of a drilling method, thorough analysis of sample data, and accurate evaluation of all the information. Knowledge of the geology of the mineral deposit is important in planning the development testing program and in evaluating the data obtained from such a program. Exploration work usually provides some significant information on the general size, shape, thickness, grade, and geology of the deposit. In some cases no further data are needed; in many cases geological complexities suggested by the preliminary work require further geological study. Of considerable importance may be the following:

Jan 1, 1968

By Ferris E. Sainsbury

As most mining companies utilize contractors rather than in-house drilling departments, it is difficult for most mining engineers to become familiar with drilling techniques This chapter will explain the various drilling options available to the mining industry through the services of a drilling contractor. It will also suggest improvements in program planning and specification writing by the mining company representatives to enable them to derive maximum benefit from the contractor.

Jan 1, 1979

By FRANK FIRRISTONE

Ix the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the dis¬trict, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Liirmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited ." Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,\

Sep 1, 1909

By F. J. Haller

The need for permanent, fireproof support indicated structural steel sets. Experience over the past six years, involving more than five miles of permanent underground openings, has proved that steel is permanent, safer and, in the long run, cheaper than either treated or untreated wood supports. Excavation is reduced, as are installation, transportation, and handling costs. A number of hazards are reduced or eliminated by the use of steel.

Jan 4, 1950

By Robert O. Davis, Phillip A. Abbott

The response of geologic materials subject to nuclear weapon effects is of considerable interest in the design of buried protective construction. Recently, more consideration has been given to placing such structures in rock rather than in soil. Although rock has the obvious advantages of high strength and low deformability, discontinuities such as joints and fault planes severely complicate any response analysis. Nevertheless, some knowledge of the effects of these discontinuities must be developed, even if that knowledge remains largely qualitative in nature. In this paper, we present a constitutive description of cracked rock subject to uniaxial shock loading. The constitutive equations are based on certain average response characteristics of a particular cracked rock model. Rather than attempt to represent each material discontinuity individually, we have incorporated the discontinuity effects into constitutive relationships for a continuous medium. The resulting equations are suitable for use in hydrodynamic computer codes presently used for ground motion calculations. APPROACH The continuum description which will be presented below is based on a detailed analysis of a particular cracked rock model. This model can be visualized as a sequence of plates (representing the intact rock) separated by gaps (representing the discontinuities). This so-called "plate-gap" model was first used by Thouvenin (1) in an effort to explain the behavior of porous materials at high

Jan 1, 1971

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By H. L. Ames, P. H. Jennings, R. W. Stanley

A process has been developed for leaching copper, lead and calcium from molybdenite concentrate. The leachant is a solution containing an oxidizing chloride (e. g., CuC12, FeC13) and an alkaline earth metal chloride (e. g., CaC12). Cupric chloride and ferric chloride, in the presence of 20-30% calcium chloride, are effective oxidants for chalcopyrite and galena. Calcium chloride, in addition to promoting the rate of leaching, serves to lower the solution pH and raise the boiling point. Leaching for two hours at 110'~ with a 1 % CuC12-10% FeC13- 30% CaC12 solution results in the extraction of up to 98% of the copper in molybdenite, 98% of the lead, and 79% of the calcium. Less than 0. 5% of the molybdenum is dissolved. The leach solution can be rapidly and effectively regenerated with gaseous chlorine and recycled. Build-up of copper and lead in the leach solution is controlled by discarding about 30% of the leach solution each cycle.

Jan 1, 1973

By Douglas J. Robinson

A pilot scale process has been developed to separate mercury, tin, silver, and copper from dental amalgam scrap. Laboratory research led to a process which was operated in 55 gallon drum sized reactors to treat 2000 Tr oz charges of scrap per day. This paper discusses the development work, presents a flowsheet and gives an indication of the equipment necessary to carry out the process on a commercial scale.

Jan 1, 1984

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By Victor Rudenno

Feasibility studies for mining projects traditionally involve in their final stages a lengthy process of repetitive trial and error discounting, in calculating the discounted cash flow rate of return resulting from the respective yearly after-tax cash flows. Also, probability analysis and sensitivity analysis (in particular) require extensive additional calculations with each change of any project parameter . These inefficient repetitive procedures have two unacceptable results: 1. they are not flexible enough to allow ready analysis of dependent parameters , and 2. they require resort to high-capacity centralised computing facilities with their inherent impersonality, rather than a convenient and available desk calculator - a factor of particular importance to top mining management. Such problems can be overcome if the mining project can be represented by a reasonable straightforward mathematical economic model. The most flexible and appropriate model has been found to be one in which a maximum and minimum value for each of n parameters are supplied to a program which determines a large number of systematic combinations of parameter events and then statistically analyses them to determine the resulting coefficients of the model. In this paper the authors discuss the selection of the most appropriate type of model and outline the steps followed in its development and application.

Jan 1, 1977

By G. Rinelli, A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxyhmine (N-BPHA) has been investkated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable at pH 2-4 with N-BPHA concentration between 2 x 10-3 mol/L and 2 x 10-2 mol/L. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti (SO4)2 to which N-BPHA was added. I. R. spectrometry of the rutile before and after treatment with N-BPHA solution confirmed the presence of this compound on the rutile surface. Adsorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U. V. technique. A hypothesis on the way N-BPHA is adsorbed on rutile is presented.

Jan 1, 1984

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 114 to 112 in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles.

Jan 8, 1960

By Bezalel C. Haimson

We have developed a new wireline hydrofracturing technique for in situ stress measurement which eliminates the need for drill rig and drill rod and renders the tripping of the straddle or impression packers continuous, fast, and inexpensive. Wireline conductors facilitate the use of downhole pressure transducers. We have confirmed the suitability of the new technique by testing it in a deep hole near the Monticello Reservoir, South Carolina. Our measurements indicate two local stress fields, one of them apparently linked to the impoundment-related induced seismicity.

Jan 1, 1984

By Maurice Cook

NORMALLY the grain size of cold-rolled and annealed copper sheet is of the order of 0.02 to 0.06 mm., and 0.1 min., for example, would, for many purposes, he regarded as undesirably large. The occurrence of very large grain sizes in a few isolated cases of copper sheet led the authors to inquire into the causes giving rise to such unusual results. During the course of this work a very large number of experiments have been carried out to determine the effect of varying the conditions of the final and penultimate rolling and annealing operations, as well as of earlier rolling and annealing treatments. A correspondingly large number of observations have been made, but within the space of one paper it is possible only to outline relatively briefly what appear to be the more important of these experiments and observations. The presentation of the results does not follow chronologically the order in which the experiments were carried out and they have been rearranged for the sake of simplicity. In recent years a considerable amount of work has been done in connection with the recrystallization and grain growth in metals and alloys that take place on annealing, and a number of generalizations have been reached. It is known that the crystal size in wrought material in the annealed condition depends on a number of factors, including the time and temperature of the annealing operations and the nature and amount of cold-work to which the material has been subjected. Results, however, that are not covered by these generalizations can be obtained, which, in some instances, may even appear to he contradictory to them. According to these generalizations gradual changes in grain size are effected by progressive variation of the factors involved in annealing or cold-working. The work recorded in the present paper, however, relates to the development of grain sizes which are far beyond those normally encountered in ordinary annealing operations and far in excess of grain sizes which, according to ordinary standards, would be classified as coarse or large.

Jan 1, 1938

By William Meyer

DURING the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have, been developed from the crude methods and apparatus of wartime to a science upon which exact engineer-ing calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1936

By AIME AIME

THE many kinds of iron and steel may be grouped into two general classes. First, there are the common steels and cast irons, made in enormous tonnages each year and used for the construction of buildings, ships and bridges, for pipe, for reinforced concrete highways, for the so-called tin cans, and by the railroads and other industries for which a low cost material is suitable. Second, there are the alloy steels and alloy cast irons, which are alloys of the chemical element iron and one or more of a large number of special elements such as manganese, silicon, nickel, chromium, vanadium, tungsten, and molybdenum. Alloy steels and irons are more costly than the common grades but their higher cost is, for many applications, justified by their superior properties, leading to ultimate economies or other advantages. They may be harder, stronger, tougher, or more resistant to rusting than the common varieties, and so are extensively used for tools, for ornamental work on buildings and in the automotive, aircraft, and other industries for, which the higher cost is compensated for by the higher quality.

Jan 1, 1933

By John E. Miller

Unit Rig & Equipment Co., manufacturer of Lectra Haul trucks, is continually studying methods of reducing the operating costs of large haulage trucks. Reduction of haulage system operating costs is an important goal that equipment operators and equipment manufacturers constantly try to improve on. One of the most variable and important factors affecting operating costs is actual truck operating practices. An examination was centered on methods to optimize truck utilization. It was found that a very effective method of accomplishing this goal would be an automatic truck control (ATC) system to automatically control a fleet of haulage trucks in a predetermined pattern. Economic studies were conducted which showed a very favorable reduction in mine operating costs by use of an ATC system. In 1970, Unit Rig & Equipment Co., in conjunction with SAAB-SCANIA began preliminary development of adapting, for truck use, a proven automated control system, previously used for train systems, small trucks, and military target vehicles. In 1974, the first prototype system was installed on a Lectra Haul M-100 and tested extensively at Unit Rig's test track in Tulsa, OK. This truck and system were then displayed publicly at the 1974 convention in Las Vegas. In 1976, the system was redesigned for production to maximize reliability, ease maintenance, and to accommodate future control and-status reporting developments proposed for haulage trucks. The new design equipment was manufactured, and a full system test will be conducted in an actual open-pit mine for an extended period to evaluate reliability, compile economic data, and obtain application information to evaluate complete mine haulage system conversions to ATC. System Description The ATC system is designed to provide automatic control of all the vehicle functions normally accomplished by the vehicle operator. The basic system consists of the on-board control equipment and the wayside control equipment. The on-board equipment receives commands from the wayside equipment and controls all the truck functions. In addition, on-board sensors monitor all critical truck functions and provide instructions to the truck and system to assure safe operation. The wayside equipment consists of a buried guidewire, block control units and a central controller which provides predetermined signals to the on-board equipment for speed control, steering, and for auxiliary functions (dumping, horn, etc.) through the guidewire located in the truck's path. The wayside equipment also controls vehicle separation, system status, and provides truck location to a central display panel. The central control panel can vary the speed level signals over any segment and can also command an emergency stop to halt all the units. [Fig. 1] illustrates a typical ATC installation. If ATC is used in operations which require flexibility and mobility at the end of the ATC guidance network, the trucks can then be operated by either radio remote control or manually to complete their assigned functions.

Jan 1, 1982