Search Documents

By J. G. Savins

Analytical procedures are described for optimizing the selection of a rheological model when it is desired to express the functional relationship between true shearrate and shearing stress in analytical form. The procedures are extended to two principal model categories — "Generalized Newtonian" and "Viscoplastic" models. Graphical examples are presented to illustrate the utility of certain characteristic deriuative functions in distinguishing between these categories and in determining how well a particular model reflects the flow behavior of rheologically anomalous materials in simple shearing flows. INTRODUCTION Modern drilling fluids and fracturing fluids, being chemically complex, are frequently non-Newtonian — a peculiarity which complicates the solution of problems such as designing flowline and process equipment, and predicting laminar-turbulent behavior, solid-suspending ability and cutting-transport efficiency. Therefore, techniques of data analysis which accurately characterize the behavior of rheologically complex materials are needed for the accurate formulation of solutions of these and similar problems. It is the purpose of this paper to describe the application of a sensitive method of rheological data analysis — the dual differentiation-integration method of optimizing the selection of the functional relation between shear rate and shearing stress — to a variety of materials of interest in drilling and production practices. BASIC CONCEPTS THE DIFFERENTIATION METHOD To a first approximation, the viscosity function for a non-Newtonian system can be expressed in a form analogous to Newton's law of viscosity by the following generalization2.3 between the stress On introducing the restrictions that the system is incompressible and the motion is rectilinear, then l = 0 and l3 = 0 ; and with the further restriction that the flow is slip-free, the viscosity (an invariant) is then determined solely by 12. With this approach one can set up a suite of integral equations relating observed kinematical and dynamical parameters for certain types of flow experiments involving simple shearing motion, e.g., flow in a cylindrical tube, flow between rotating concentric cylinders, and flow between fixed parallel surfaces of large aspect ratio. Taken in the order cited, these integral equations are as follows.

By G. C. Wallick, W. R. Foster, J. G. Savins

A comprehensive review of the salient features of the differentiation method of rheological analysis in Poiseuille flow from its inception circa 1928 is presented. Here no initial assumptions regarding the nature of the function relating rheological parameters to observed kinematical and dynamical parameters are required in the data-analysis process. In contrast, the integration method involves interpreting flow properties in terms of a particular ideal model. It is shown that, although both methods represent modes of solution of the same integral equation, being relatively bias-free, the differentiation method offers a more discriminating procedure for rheological analysis. The application to problems involving plane Poiseuille flow is also described. INTRODUCTION In most instances, the approach to the problem of interpreting the rheological properties of various compositions as they are affected by changes in chemical or physical environment, assaying the characteristics of a particular constituent of a suspension, analyzing flow behavior in terms of interactions between components in a system, to cite but a few examples, has been in terms of what Hersey1 terms the integration method. Briefly, it consists of interpreting flow properties in terms of a particular ideal model. The usual practice of the integration method is to choose a model with a minimum number of parameters because, other things being equal, it is desirable to use the simplest model which will describe the behavior of a real material and yet be mathematically tractable for the requirements of data analysis. This expression is then substituted into an equation which relates observed kinematical and dynamical quantities, such as volume flux Q and pressure gradient ], and angular velocity and torque T, in a capillary and concentric cylinder apparatus, respectively. The rheological parameters appear on integrating, in an expression relating the pairs of observable quantities such as those just given. In many instances a particular model provides a good representation of rheological behavior over a reasonable range of compositional and environmental changes. Just as often, however, it is obvious that the interpretation of rheological changes by the integration method is not providing realistic information about changes in flow behavior. A more general method of interpreting rheological data for a given material is to make no initial assumptions regarding the nature of the function relating rheological parameters to observed kinematical and dynamical quantities, e.g., flow rate and pressure drop in capillary flow or angular velocity and torque in a rotational viscometer. This general method Hersey1 terms the differentia-ation method. Instead of integrating, one differentiates the integral equation with respect to one of the limits, i.e., one of the boundary conditions; the resulting expression contains the same observable quantities just given, their derivatives, and the rheological function evaluated at that boundary. By obtaining these derivatives from experimental data, graphically or by a computer routine, they can be substituted into the differential equation and a graphical form of the function derived. THEORY OF THE DIFFERENTIATION METHOD FOR POISEUILLE-TYPE FLOWS In this introductory paper, two flow cases which are important in viscometry are considered (one for the first time) from the differentiation method of analysis, flow in a cylindrical tube and flow between fixed parallel surfaces of infinite extent, the basic integral equations being formulated in a manner analogous to the way they originally appeared in the literature. In addition, the following ideal conditions will be assumed: (1) an absence of anomalous wall effects, (2) isotropic behavior everywhere, and (3) steady laminar flow conditions. Before proceeding it would seem appropriate to preface the analysis of these flow geometries with the comment that the basic philosophy of the differentiation method could be said to stem directly from the efforts of Herzog and weissenberg2 to indicate systematically the various ways of using

By G. C. Wallick, W. R. Foster, J. G. Savins

Inasmuch as the differentiation and integration methods represent different modes of rheological analyses, a dual scheme of analysis using both methods should lead to a generalized method of data analysis. A dual differentiation-integmtion method of analysis is applied here to the Poiseuille flow of a variety of ideal Generalized Newtonian and viscoplastic models. Using machine-processing techniques, the result is a spectrum of response patterns which are expressed in terms of certain derivative functions. It is shown that these characteristic functions form the basis of a highly-sensitive analytic technique for optimizing the selection of the most appropriate functional relationship between shear rate and shearing stress. INTRODUCTION In the first paper of this series, Savins, Wallick and Foster1 presented an historical review of the salient features of the differentiation method of rheological analysis in Poiseuille flow, and also indicated how the method could be applied to problems involving plane Poiseuille flow. It was shown that the differentiation and integration methods, although basically not incompatible, do represent different modes of rheological analysis. This suggests that valuable background information regarding the probable response characteristics of real data obtained with the differentiation method can be obtained from an integration method-differentiation method analysis of the response of a variety of ideal rheological models. The present paper describes how this dual method of analysis has been applied to suites of idealized models representing a wide variety of Generalized Newtonian and viscoplastic behavior which have received attention at various places in the literature.

By M. A. El-Aouar

Drilling muds are complex colloidal systems. In an effort to analyze the physical properties that affect their performance at high temperature, an investigation was made of the hydrothermal stability of the monoionic hydrogen, calcium and magnesium forms of montmorillonite and attapulgite. Samples were heated to 400°1F in a simple autoclave and analyzed for cation exchange capacity, c-axis X-ray diffraction spacing and pH factor us sodium hydroxide titration dependence. Out of the six monoionic clay minerals tested, calcium montmorillonite and magnesium attapulgite showed the least base exchange capacities and were relatively unaffected to heat. It is concluded that, of the six clays studied, these two clays were the most suitable forms for use in drilling fluids. INTRODUCTION The drilling of deep wells is dependent upon the drilling mud, and problems frequently arise concerning the effect of mud temperature and prolonged heating. Drilling muds are complex colloidal systems. In an effort to analyze their behavior in deep, hot boreholes, it was thought desirable in this investigation to study suspension of pure, monoionic montmorillonite and attapulgite clays before and after hydrothermal heating. Chemically, clays are hydrated aluminum silicates, such as montmorillonites and attapulgites. The structure of montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. Attapulgite consists of double silica chains running parallel to the c-axis with the chains linked together at their longitudinal edges. The apexes of the tetrahedrons in successive chains point in opposite direc-tions.4,7,10 One of the most important characteristics of clay minerals is their property of sorbing certain anions and cations and retaining them in exchangeable state. The property of exchange capacity is measured in terms of milliequivalents (meq) per 100 gm of clay. The cation-exchange capacities are taken at pH 7 from titration curves which show the relation between pH and milliequivalents of added NaoH.9,11 The following are causes of cation exchange: (1) broken bonds around the edges of the silica alumina units would give rise to unsatisfied charges, which would be balanced by adsorbed cations; (2) substitution within the lattice structure of trivalent aluminum for quadrivalent silicon in the tetrahedral sheet and of ions of lower valence; and (3) the hydrogen of exposed hydroxyls may be replaced by a cation which would be exchangeable. The primary techniques employed to study the effects of hydrothermal treatment were titration curves and X-ray diffraction analyses. Titration curves were useful in characterizing the nature of the clay mineral surface and the stability of the various samples to attack by acid or alkali before and after hydrothermal treatment. X-ray diffraction analyses were used to determine changes in the nature and crystal structure of the minerals present and to determine the cations in exchange positions on the montmorillonite samples. EXPERMENTAL PROCEDURE PREPARATION OF SAMPLES Selected samples of Wyoming bentonite and attapulgite clay from mines along the Georgia and Florida border were purified by centrifugation to remove all particles larger than 2 microns. In preparing magnesium attapulgite, first a 1.00-normal solution of magnesium acetate was prepared. The pH of the solution was adjusted to 7.0 by adding magnesium oxide. One hundred grams of attapulgite clay were mixed in a blender for 30 minutes with the magnesium acetate solution. The attapulgite solution was left overnight, and then filtered in a Buchner funnel. The suspension was leached with further quantity of magnesium acetate solution and then washed with distilled water for 20 days, after which the filtrate was free from magnesium ions. The concentration of magnesium attapulgite in the clay slurry was adjusted and determined quantita-

By R. W. Brown, J. L. Loper

The process of sand erosion has been harnessed to perform a useful function—the directed perforating of oilfield tubular goods and formation rock. In this process the sand is carried by a liquid medium and the resrrlting slurry is forced through a nozzle at an extren~ely high velocity. Upon impingement against casing or formation, the fast-moving sand particles erode a perforalion in the casing followed by cavity formation in the medium behind the casing. The many factors influencing the rate and extent of this penetration are inherently difficult to establish experimentally. Equations describing submerged jet behavior have been applied to these conditions. The following paper develops the equations for predicting the performance of the perforating jet. INTRODUCTION The cutting power of high-velocity sand has been well known in the petroleum industry for many years. Sand carried by a high-velocity gas stream causes severe erosion. This effect has been the cause of numerous production problems in certain areas. It was logical to expect that this phenomenon would one day be adapted to useful industrial applications. Development of mobile, high-pressure, high-horsepower pumping equipment in the last decade has made this possible. The sand erosion process involves pumping a fluid containing abrasive solids through a set of nozzles at a high differential pressure (2,000 to 4,000 psi). The pressure conversion into kinetic energy imparts high velocity to the sand particles which, upon impact with the formation face or casing wall, erode the material in an organized pattern. This paper attempts to establish the effects of the various parameters and to predict the performance and limitations of the process. The following factors will be considered: nozzle differential pressure, perforation size, sand concentration, nozzle stand-off distance and backpressure. In general, this discussion is presented along theoretical lines and is substantiated by field results and data where reliable field data exists. POWER EQUATIONS The penetration rate of a high-velocity hydraulic jet is proportional to the power or energy of the jet at the point in quesion. The power of the submerged jet will decrease with distance (or penetration) into the cavity created by the jet. As the cavity is extended into the formation, the power of the jet diminishes to a value equal to the threshold cutting power of the particular formation which is defiined as the lowest power level at which the formation will be abraded by the jet. Obviously, when this point is reached, no further cutting of the formation can occur. It is assumed that this power level for a particular formation is a function of the hardness of that formation. The following equation can be written for the hydraulic process of formation abrasion.

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By C. Gatlin, F. Armstrong, K. E. Gray

This paper presents some preliminary results of two-dimensional cutting tests of dry limestone samples at utmospheric pressure. Cutting tips having rake angles of + 30°, + 15", 0°, - 15" and - 30" were used to make cuts on Leuders limestone samples at six depths of cut ranging from .005 to ,060 in. at cutting speeds of 15, 50, 109 and 150 ft/min. The vertical and horizontal force components on the cutting tips were recorded with an oscilloscope equipped with a polaroid camera. Motion pictures of the cutting process at camera speeds of 5,000 to 8,000 frames/sec were taken at strategic points in the variable ranges. The movies provide considerable insight into the brittle failure mechanism in rocks. It appears that chip-generating cracks usually have an initial orientation which is related to the resultant of the externally applied forces. The latter part of the crack curves upward toward the free surface being cut, this part being governed by some type of cantilever bending or prying. The linear and angular motion of the loosened chips also indicate the tensile nature of brittle failure. Analyses of the forces on the cutting tips indicate that: (I) relatively small increases in vertical loading result in large cut-depth increases for sharp tips (rake angles 2 0"); (2) tool forces increase at an increasing rate as the rake angle decreases, particularly for rake angles < 0"; and (3), for the range of this study, rate of loading had little effect on the maximum forces. Both the movies and visual inspection of the cuttings indicated that the volume of rock removed by chipping was much larger than that by any grinding mechanism, even for tips having negative rake angles. Cutting size increases with increased cut depth and rake angles, and decreases slightly at high cutting speeds, the depth of cut having by far the most influence. The amount of contact between the rock and the cutting tip was always less than the depth of cut and rarely exceeded 0.010 in. even for cuts of 0.060 in. INTRODUCTION The planing (or slicing) of various materials with a fixed blade has long been practiced by workers in many industries. For example, the farmer&apos;s plow, the carpenter&apos;s plane and the housewife&apos;s paring knife all employ this basic action. The casual observer might suspect that something so common must be quite simple; however, as in all problems involving the failure of materials, such is not the case. Industries concerned with the machining of metals have long studied these problems, and their literature on the subject is voluminous. Despite these efforts, basic knowledge is not very advanced, as may be noted from recent and comprehensive analyses of their literature.12 Metals are more subject to analysis by classical theories of elasticity and/or plasticity than are rocks, since their elastic constants and strengths are reasonably well established in many cases. In spite of this relative "simplicity", Hill9 refaces his discussion with an admission that the mathematical solution to the machining problem is not known. Photoelastic studies of both machining and milling have been performed and are discussed thoroughly by Coker and Filon.4 Rotary drilling of rocks with fixed blade or drag bits has long been practiced by the mining and petroleum industries, and considerable study has been given to defining their cutting action in terms of the pertinent variables. Essentially all the published mechanistic research on drag-bit drilling has been performed by mining engineers and has been concerned only with rocks in the brittle state. Fairhurst5-7 has worked extensively in this area and employed photographic techniques quite similar to those reported here, except at much lower speeds. His studies showed the periodic or cyclical nature of the brittle failure mechanism, in which instantaneous loads on the bit varied from some maximum value to near zero. Goodrichs has presented further data on the subject as well as a qualitative description of the process. Again the postulated mechanism is cyclical, with alternate chipping and grinding periods. The ploughing of coal is a practiced method and has been studied in some detail by English mining engineers."" Their findings have considerable general application to drag-bit drilling. Evans," in particular, has extended Merchant&apos;s metal-cutting theory" to brittle materials with some success, although certain aspects of his theory are open to question. Fish13 has recently summarized nearly all the published works concern-

By L. C. Reese

The ultimate resistance against a rigid cylinder which is moved laterally in a cohesionless soil is a function of the geometry of the cylinder and the properties of the soil. An approximate method is developed for computing this resistance and is tested against results of laboratory experiments. Satisfactory agreement between the method and experiment was obtained. Not only was the ultimate resistance against the cylinder measured, but measurements were made of the shape of the rupture surfaces. These measurements should allow the development of a more rigorous computation procedure. INTRODUCTION A critical aspect in the design of offshore drilling platforms is assuring the stability of the platform during a hurricane. The large horizontal loads from waves and wind make a severe loading condition. Piles are generally employed as the foundation since they can be effective in resisting both horizontal and vertical loads. Spuds are sometimes used with a mat foundation, where the spuds are designed principally to resist horizontal loads and the mat designed principally to resist vertical loads. The research reported in this paper is related to one aspect of the problem of laterally loaded piles or spuds in sand. The complete solution to the problem of the laterally loaded pile in sand would require the prediction of soil resistance against the pile as a function of pile deflection; only the ultimate resistance against short piles is considered in this paper. A considerable amount of additional research will be necessary in order to obtain a complete solution to the problem of the laterally loaded pile in sand; however, the work reported here should be useful as a guide in the performance of some of the additional research. ULTIMATE LATERAL RESISTANCE AGAINST A LONG FALL IN SAND To aid in the understanding of the theory which is developed for a cylinder, the theory for earth pressure against a wall is reviewed. In Fig. l(a), a long wall of height H is shown embedded in soil. Soil resistance will develop as the wall is deflected, and the soil resistance will increase with deflection until some limiting value is reached. In this discussion, and those following, it is assumed that all points on the wall deflect equal amounts. A possible shape of the real curve which relates soil resistance to deflection is shown by the dashed line in Fig. l(b); however, as a means of simplifying the discussion, an idealized curve (shown by the unbroken lines) is drawn. If such a wall as this were furnishing the horizontal support for an offshore structure, the dashed curve in Fig. 1 would be the information needed in performing a foundation analysis, with the idealized curve possibly being an acceptable substitute. For the idealized curve, the soil resistance is linear with deflection for the early portion of the curve such that

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well&apos;s results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. &apos;This means that careful measurements of surges occurring in actual field operations must be made.

By R. K. Matheson

THE Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 19o tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65° From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. CHOICE OF RAISE A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. TIME SCHEDULE As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1942

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By Victor L. Stevens

The Oso tunnel is one of three tunnels located on the San Juan-Chama Project in south-central Colorado. The purpose of the tunnel is to carry water from the upper San Juan watershed through the Continental Divide into the Rio Grande watershed. The Oso tunnel contract was awarded by the U.S. Bureau of Reclamation to a joint venture of Boyles Brothers Drilling Co., Gibbons & Reed Co., and Cimco in February 1966. The Oso tunnel is 26,660 ft long and has a rock section of 10 ft, 2 in. with a lined diameter of 8 ft circular. The main portion of the rock formation was in the Lewis shale. This formation is quite consistent in hardness and texture with exception of localized limestone concretions and sandy siltstone inclusions. The job was bid on the basis of using a James S. Robbins mole of the P221 series. The decision for using a mole was predicated on the geology and the experience of the same joint venture on the adjoining Azotea tunnel where a mole was successfully used. The Robbins P221 series mole is capable of cutting from 9 ft, 11 in. to a 10 ft, 7 in. diam without any major change. It is 40 ft long and weighs 60 tons. The cutting head has 22 disk-type cutters and one center pilot (standard 9 7/8 -in.) tricone bit. The head is powered by four 75 hp electric motors. Gripper pads at about the midway point on each side of the machine are pushed into the tunnel ribs and thrust-cylinders in front of each gripper apply pressure to the face as the head rotates. The regripping cycle is 3 ft and then the grippers are retracted and advanced. Each cutter on the perimeter of the head is followed by a bucket which scoops up the cut material, almost in the same manner as a water wheel, and dumps it into a conveyor situated along the top of the mole. The muck from the mole conveyor is dumped into a gantry-type conveyor. The gantry conveyor is 350 ft long and is pulled

Jan 1, 1970

By P. W. Allen

Here are the facts and the figures on how Tahawus cut costs and improved safety in solving their secondary breakage problem - A dropball crane entirely eliminated secondary blasting.

Jan 4, 1953

By Ray Arms

This paper includes a brief classification of dry-cleaning devices, with a theoretical discussion of the principles involved. It outlines the methods of handling dust and screening difficulties at the McComas plant, as well as other plants that are being constructed and other dry-cleaning devices being developed. It describes the American Pneumatic Separator and discusses the sizing required, the effect of moisture in the raw coal, disposition of the middlings, and other aspects of the process. It gives s results of tests on various coals, and results of operation at Raton and McComas. DRY CLEANING, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group&apos; also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc.

Jan 3, 1924

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William F. Lawrence

INTRODUCTION Cleaning fine coal sizes utilizing air currents in machines as the primary separating medium is called dry concentration or pneumatic cleaning. In 1947 approximately 18 million tons (16.38 million mt) of bituminous coal were cleaned by air machines; in 1965, 25.4 million tons (23.1 14 million mt); but in 1975, only 7 million tons (6.37 million mt). Table 11-1 shows the tonnages cleaned of bituminous coal and lignite in the United States by various types of equipment from 1938-1963. Table 11-2 shows only tonnages cleaned by pneumatic methods from 1964-1975. The decrease in tonnage to approximately 7 million tons (6.3 million mt) is due to a higher moisture content in the mined coal and the greater difficulty in cleaning the coal by air. There also was a definite trend to load raw coal at the mines, especially the slack which is the most expensive to clean due to the dewatering and drying requirements. While there have not been any applications of pneumatic cleaning in the anthracite field, its use has not been fully explored. The same is true for lignite and subbituminous coals.

Jan 1, 1979

By A. F. Bridge

IN order to show the need for gas reserves, their control, and conservation, in California, it is necessary to describe briefly the local conditions under which gas is produced and marketed, to point out the lack of coordination between supply and demand, and to relate the history of efforts to prevent wastage. There are now 24 fields in California producing a surplus of gas over field fuel requirements. They are usually grouped geographically into three divisions, as follows: (I) Los Angeles Basin (Los Angeles and 0 r a n g e Counties), thirteen fields, all casing-head gas. Total daily gas available for sale 125,000, 000 ?cu.ft. (2) Coastal (Ventura and Santa Barbara Counties). Seven casine-head and one dry gas field. total-avail- able daily, 165,000,000 cu.ft. (3) San Joaquin Valley (Kern, Kings, Fresno, and San Joaquin Counties). Four casing-head fields, five dry gas fields, and two producing casing- head and dry gas from different zones. Total available daily pro- ducticon, 475,000,000 cu.ft. Total all fields, 765,000,000 cu.ft. daily.

Jan 1, 1936

By Linn Bradley

Introduction MARKED differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 2, 1917

By Linn Bradley

F. H. WILLCOX, Pittsburgh, Pa. (communication to the Secretary*). -We must keep in mind, in balancing the savings-to be anticipated by the most efficient combustion of gas, the best heat absorption by stoves or boilers, and by heat conservation of the thermal equivalent carried in. blast-furnace gas-against the cost in operation, maintenance, depreciation and interest charges of the equipment required to realize the savings, that in boilers and hot-blast stoves we are basing our economies upon two different, combustion phenomena. In a boiler, evaporating water at a heat efficiency of 70 per cent., approximately 47,550 B.t.u. is consumed per boiler horsepower. Taking the blast, furnace gas cited in the above paper, we are using about 38 ¾ lb. of cold-washed gas per boiler horsepower. Using the hot-cleaned gas, the same equivalent heat is furnished by 34 1b. of the gas , This leaves of the 38 ¾ lb. required in the case of cold-washed gas, 4 ¾ lb. or 6,650 B.t.u. available for raising more steam when dry-hot gas is used, which means that an equivalent amount of coal firing can be dispensed with. Per ton of iron, this figure 2/3 X 12,000/38.75 X 4.75 = 980 lb. gas or 1,372,000 B.t.u. or 100 lb. coal. At $1.50 per ton of coal, the net saving per ton of pig iron produced by the use of dry-hot over wet-cold cleaning will, therefore, be about $0.06 2/3. At a stove heating 8,500 lb. of air per toil iron from 150° F., one-quarter of the dry-hot cleaned gas, or 3,000 lb., would heat the air to 1,450° F. 3,000 X 1,400 X 0.70 = (8,500 X 0.255) = 1,300. The cold-wet gas would heat the same amount of air to 1,280° F. 3,000 X 1,225 X 0.70 = (8,500 X.0.255) = 1,130.

Jan 4, 1917