Search Documents

By Carl F. Floe, John Chipman

A YEAR ago the authors published a paper on the solubility of sulphur dioxide in molten copper.1 The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: [ ] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above l00 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu20 and (a; 2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of SO2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. EXPERIMENTAL METHODS The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By George A. Roberts, Robert F. Mehl

WHEN austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.1 This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced,4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ae1.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. EFFECT OF INHOMOGENEITIES ON REACTIONS NEAR Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously;1,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional quantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a "fine-grained steel." These steels can be compared at the same grain size by heating C to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By B. Ball, C. H. Cox, S. N. Yap

Electrokinetic measurements on cassiterite were made in the presence of sodium di-hydrogen phosphate, mono-hydrogen arsenate, bisulfite, and sulfate. Flotation studies were also conducted using sodium dodecyl sulfonate in the presence of these salts. It was found that the anions specifically adsorb on cassiterite in the order H2AsO-4 H2PO4 HSO3 SO4 and consequently cause flotation depression. The adsorption mechanisms of the various inorganic anions are discussed in detail.

Jan 1, 1980

By A. A. Smith, J. S. Smart

NUMEROUS investigations of the effects of the various impurities common to commercial coppers have been published, and the data have found wide use in industry. Naturally, emphasis has been placed on the oxygen-bearing coppers of the tough-pitch variety, but need is now evident for data covering the oxygen-free condition as well. Furthermore, relatively few of the important reactions between oxygen and the various impurities are well understood, and often the data at hand are not applicable to the low concentrations encountered in commercial coppers. This paper presents the changes in conductivity and softening temperature derived from individual additions of the group VIII triad, iron, cobalt and nickel, to high-purity copper, and constitutes a portion of the copper-research program being conducted at the Central Research Laboratory of the American Smelting and Refining Co. The method of preparation of high-purity copper and its alloys in either the oxygen-free or oxygen-bearing form has been described previously.1 The purity of this material, and the methods developed to produce it, provide the means for direct investigation of the very low concentration range in which the various impurities generally exist in commercial coppers. The usual necessity for extrapolation to this range using the results obtained from higher concentrations, and the interfering effects of extraneous impurities, are thus simultaneously circumvented. Since previously published data have adequately presented the effects of higher concentrations of iron, cobalt and nickel, the present investigation has been confined to the composition range 0 to 0.05 per cent. All alloys were initially prepared in the form of oxygen-free continuous cast rod, the weighed alloying additions in suitable form being charged with the pure copper to the continuous casting crucible. The best of the available high-purity alloying materials were used, and spectrographic analyses confirmed the absence of interfering elements from the alloys formed. Each series was compounded in the direction of increasing concentration, starting with pure copper in a new crucible and finishing with the 0.05 per cent alloy. Composition was closely controlled by adding the alloying element in the form of a carefully compounded and analyzed master alloy rendered uniform by continuous casting. The accuracy of this method of synthesis was proved by chemical analysis of the more concentrated alloys, and, accordingly, there is every reason to credit the stated composition of the very dilute alloys in the range where chemical analysis becomes highly uncertain. Oxygen-free samples for measurements of conductivity and softening temperature were obtained by drawing the continuous cast rod to wire of 0.081-in. diameter, employing a number of intermediate anneals to refine the grain structure. The

Jan 1, 1942

By H. R. Hoffman

SINCE slag is a necessary product of the reactive oxygen additions necessary to the present-clay quality steelmaking, the study of the control of its volume is being attempted. With other varying factors that may affect the volume of slag kept as nearly constant as possible, the object of this investigation is to determine what effect the one factor of varying the amounts of iron-ore additions and the time of the additions may have upon the volume of slag in producing an acid electric steel heat.

Jan 1, 1947

By F. G. McCutcheon

UNTIL about 1930, the universal practice of horizontal-retort zinc smelters in the United States, as far as the writers are aware, was to operate the retort furnaces on a 24-hr cycle; that is, the retorts were charged in the early morning of one day, and in the early morning of the following day the residues were cleaned out, the retorts recharged, and a new cycle started. During the business depression of the early thirties, zinc production fell off to the extent that zinc smelters had idle retort capacity. Rather than continue to run some of the retort furnaces on a 24-hr cycle and shut down the remainder, a few companies decided to try out a longer cycle. Although the output of zinc per retort per day is lower, the longer cycle permits a larger charge per retort and improved zinc recovery. Advantages of the longer cycle were soon evident, and the practice spread rapidly. Various lengths of cycle were used, typical examples being 28-hr, 32-hr, 36-hr, and 48-hr. The 48-hr cycle fits in best with the standard routine of smelter practice that was built up on the basis of the 24-hr cycle; that is, the retort furnace "maneuver" always comes at the same time of day, and can be performed in the cool hours of the early morning. Under some conditions, particularly in some of the older plants, where the retorts are smaller than in newer plants, a 48-hr cycle is longer than necessary, and some intermediate length of cycle may theoretically be most economical. Use of an intermediate cycle, however, means that the maneuver comes at different times on consecutive days, and that sometimes it comes during the hottest part of the day. The work on the retort furnaces is extremely hot and arduous at best, and it is much worse, of course, if it is done during the heat of a summer day. When labor was plentiful and tractable, many plants were able to operate on cycles of intermediate length, but the workmen did not like the working hours. Under present labor conditions, it is hardly practicable to operate with a cycle of intermediate length, so the choice has narrowed down to the alternatives of 24-hr or 48-hr cycles. In any discussion of economics, too comprehensive generalization is not warranted, because local conditions affecting economics vary greatly. The best economic practice at one plant at any given time may be uneconomical at another plant, or even at the same plant at another time. To determine the length of cycle that is the better practice at a given plant at a given time requires a weighing of the advantages and disadvantages of each cycle, taking into consideration all the local conditions. Some of the factors that must be considered in making the comparison are discussed briefly in the following paragraphs.

Jan 1, 1947

By H. A. Kortmann, K. Koch, B. M. Grover, O. P. Burghardt

Addition of lime, especially when treating a hematite feed, sometimes results in swelling and a severe loss in strength during reduction in the temperature range 900° to 1100°C and in grain disintegration in the temperature range 400° to 600°C in a weakly reducing atmosphere. Swelling and/or grain disintegration of pellets is often the reason for trouble in blast furnace operation, resulting in a decrease in the rate of smelting. Following a brief description of the test procedures employed (measurements of swelling, pressure-reduction-softening and grain disintegration), some results are given which were arrived at when testing pellets from industrial plants. Results of systematic tests are presented, where the effect of the quantity and quality of the gangue upon the behavior during reduction of pellets is illustrated. Varying amounts of quartz and limestone were added to a high-grade hematite ore and, then, pellets produced in a pot grate. The relationships of the behavior of the fired pellets during reduction are presented, among others, in the ternary system CaO-FeOn-SiOP. Finally, an attempt is made to explain the reasons for swelling, loss in strength, and grain disintegration.

Jan 1, 1974

By E. J. MCOAUSTLAND

THE behavior of steel after overstrain and at moderate temperatures is fairly well known. It has been made the subject of much investigation, and our knowledge is clear and definite on many points. The ultimate raising of the elastic limit, after moderate overstrain, and the consequent lowering of the ductility, seem to be well established. It is also well understood that the immediate effect of overstrain is to lower the elastic limit, possibly to zero, but that if not interfered with, this limit will subsequently rise higher than before. The "tests after moderate temperature," reported in this paper, were undertaken to verify the above statements for the particular steel under investigation, and also to determine, if possible, the total time required for complete recovery from this state of overstrain. The behavior of overstrained steel at temperatures at or below 32° F. is not so well known. Tests made by Prof E. G. Coker, at McGill University,' show that steel, overstrained and subjected to cold, will remain in a state of overstrain for an indefinite period. I am not aware of any other published results of tests along this particular line. The effect of time and temperature on the recovery of steel from overstrain was made in 1902-3 the subject of sortie investigation in the laboratories of the College of Civil Engineering of Cornell University. A general plan was outlined in connection with the regular courses of instruction in testing of materials; but the press of routine work and the demands of the schedules on the time of the students were so great as to presage long delay in the completion of the work. Not much had been accomplished up to 1904-05, when Messrs. E. C.

May 1, 1906

By C. C. Spencer

A CHARGE of 12,200 lb of scrap was used on all heats. The slag materials that were added to the furnace along with manganese ore were kept constant; that is, 230 lb Coxey sand was put on the banks at the slag line before each heat was charged, 35 lb limestone was added after the carbon boil. manganese ore was the only item varied in the four series described herein. I might add here that it is impractical for us to get the carbon clown in one boil, for the steel would come out through the doors and run over the floor. We take the carbon down in two vigorous boils.

Jan 1, 1947

By M. T. McDonough

THE data relative to the effect of metal depth on slag volume was obtained from the operation on two acid electric furnaces in which heats of various sizes were produced. The furnaces used were of 3 and 5-ton rated capacity; the heats investigated ranged from 6 to 8 tons. Heats of 7 and 8 tons were made in the larger furnace; heats of 6 tons in the smaller one. Bath depths and diameters were measured on the furnaces when cold and each is accurate to one inch. Both the metal charge and the slag were weighed on a track scale accurate to ± 25 lb. All other components added to the furnace were weighed on a wheelbarrow scale accurate to ±5 lb.

Jan 1, 1947

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time.

Jan 1, 1950

By George Breyer

DURING the past 25 years the steelmaker has experienced some difficulty in producing steel to meet the standards established by the metallurgist. In contrast to the past, when a chemical specification of broad limits was the only requirement, he now has to employ such tests as microscopic, macroscopic, tensile, impact, Magnaflux and even X-ray and supersonic. The development of these tests has more than set the pace for a manufacturing process of which the exactness still hinges to an important degree on the ability of the furnace operator. In our efforts to produce steel, and especially alloy steel, to meet the exactness of modern engineering specification, many factors must be taken into account. It is not sufficient to make a good heat of steel in the furnace and then be satisfied that the job is done, since there are many pitfalls between the furnace and the finished product. The literature abounds with information on melting practices, deoxidation methods and slag control, but the lack of positive information about what happens when the steel is teemed into molds is quite evident. Such questions as what is the proper mold size, shape and thickness; which is the best mold coating; what is the best rate of pour for any given steel, and what is the effect of cooling rates on quality, are still answered by opinions. It is acknowledged that a poor heat of steel cannot be improved in the pouring pit. On the other hand, a good heat can be ruined by improper handling after it leaves the furnace.

Jan 1, 1947

By Walter S. Weeks

IN this paper the effect of natural ventilation pressures is considered a part of the mine resistance and it is shown that their effect on the mine resistance is not the same as the total natural ventilation pressure of the shafts if the mine has several levels. It is shown that increasing the fan pressure causes the division of the air to approach the condition that would obtain if there were no natural ventilation pressure present. It is shown that if an appreciable difference in pressure is maintained between the beginning and end of a group of splits, the value of the integrated effect of the natural ventilation pressures on the individual splits does not change substantially with moderate changes of this pressure. A method is outlined for determining the resistance factor of the mine and the value of the effect of natural ventilation with the fan operating; also a method for determining this factor when circulation is caused by natural ventilation alone. NATURAL VENTILATION PRESSURE Natural ventilation pressure (N.V.P.) is caused by the difference in weight of the air in two similar columns between two horizontal planes, and the difference in weight is caused principally by the difference in temperature of the two columns. The fan pressure causes some variation in density, but, since it is usually small and affects both columns, its effect is relatively unimportant. It has been suggested that "N.V.P." be called "stack effect"; but, since the term N.V.P. was used in a previous Institute paper,' applied in exactly the same manner, the term will be used. FRICTIONAL RESISTANCE The frictional resistance to flow in a mine without natural ventilation may be expressed as RQ2 where R is a constant for a given air density and Q is the rate of flow. This frictional resistance plus the effect of velocity changes will be called the F pressure (F.P.) and a curve of F.P. against Q, the F characteristic of the mine. If a pressure is applied to a mine by a fan, the air flow so adjusts itself that the drop in pressure through any path from entrance to exit of mine, due to frictional resistances and velocity changes, is the same as that in any other path. The mine resistance varies as the square of the quantity. The air distribution without N.V.P. will be called "normal." NATURAL VENTILATION PRESENT When N.V.P. is irregularly distributed in a mine, it is more convenient in analysis to consider the N.V.P. as a part of the duct resistance. If it is so considered the resistance no longer varies as the square of the quantity, and if N.V.P. exists between levels the distribution of the air is no longer normal. The total N.V.P. of the mine is the pressure caused by the full length of the shafts. If a mine has several levels, N.V.P. exists

Jan 1, 1944

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

By A. K. Burton

This paper reviews transportation trends in large base metal open-pit mines in recent years. Particular attention is paid to the unprecedented increases in the cost of oil and its effect on operating costs. Fuel conservation and measures to improve trucking efficiency are considered. The paper also discusses viable alternatives for reducing or eliminating the use of trucks. Various advantages and disadvantages of using conveyors to transport shot rock from the mine are reviewed. The paper concludes with some observations on current policies and trends primarily aimed at mitigating the high cost of energy.

Jan 1, 1983

By K. Aoki, N. Kameda, T. Esaki

The shortage of adequate construction sites and their difficult location has compelled many engineering structures to be planned in old mining areas in Japan. This paper shows, first, the characteristics of the excavated underground environment and next, the necessary preventive measures during construction of surface structures. Where the depth of a mined out area is relatively shallow, there is a tendency of cave-in consequent to surface loadings. The effect of surface loadings is inversely proportional to the depth of goals. Finally, a power plant project is studied as an example.

Jan 1, 1984

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

By E. Stansfield

THIS test was described in a privately circulated First Progress Report on Slacking Characteristics of Coal, by A. C. Fieldner and W. A. Selvig, May 1, 1928. The test was described in detail in U. S. Bureau of Mines Report of Investigation 3055, in November, 1930.1 The test, in brief, is conducted as follows: A sample of freshly mined coal consisting of 18 to 25 pieces approximating 1 ¼ cubes, and weighing 500 to 600 grams, is taken for the test. The sample is subjected to a "blank sieving" of carefully regulated degree, on an 8-in. circular sieve with 0.263-in. square openings; and the undersize and oversize weighed. The oversize is placed on a sheet-iron pan and dried for about 24 hr. in an A.S.T.M. air-drying oven maintained at 30° to 35° C. through which a current of warm air is drawn. The sample is then cooled to room temperature and immersed for one hour in water at the same temperature. The water is then drained off, the sample dried for 24 hr. as before, cooled, sieved as before, and the oversize and undersize weighed. The percentage weight of the undersize, is calculated and reported as the first cycle loss. This loss, corrected by subtracting the percentage loss in the blank sieving, is termed the slacking index. The sample may be subjected to further cycles of wetting, draining, air-drying, sieving and weighing. In a letter (August, 1932) W. A. Selvig approved making the blank sieving on a duplicate sample, rather than on the sample used for the test, where sufficient coal was available. This method is now employed in these laboratories. The accelerated weathering test has been employed in the labora-tories of the Research Council of Alberta, at Edmonton, since 1928, but not found entirely satisfactory as repeat determinations with samples taken from the same or adjacent mines frequently showed serious differ-ences. Differences must be expected as the coal may vary in the seam, and the selection of a typical set of lumps approximating 1 ¼ -in. cubes

Jan 1, 1934

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has-been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1 volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 904 volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928