Search Documents

Discussion of the paper of R. H. RICHARDS and BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 191.5, pp. 67 to 72. R. H. RICHARDS, Boston, Mass.-I believe that the manner of working for efficiency in almost all lines is to study the conditions of highest efficiency, and then to measure what is being clone. We can then see how near we have approached the highest efficiency. Spigots in practice often use many times the water theoretically needed. There are places where that is necessary for safety reasons. There are, however, places where it is unnecessary, and in these places it seems to me that this work of Mr. Dudley's will be a great help to the mill man to arrive at the greatest economy of water and highest efficiency. ALBERT R. LEDOUX, New York, N. Y.-A good many years ago I received a telegram from that distinguished engineer, Hamilton Smith, which simply said in substance: "I have discovered that liquids will flow faster from a square orifice than from a round orifice of the same area, under the same head." I wondered why he sent me the telegram, but some time afterward he told me that he had been making experiments along that line in Montana; that he thought the discovery was interesting

Jan 5, 1915

By O. W. Ellis

CERTAIN alloys1 that, as a result of quenching, are retained in the form of homogeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys" that, on rapid cooling, are held in the form of homogeneous solid solution (as, for example, certain steels) behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as "aging" or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 7, 1924

By Thomas M. Drown

IN the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down-accurately to one inch section. These were immersed in a large wrought-iron pot full of molten sodium carbonate made by fusing the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling was broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By J. E. Gosline

IN any theory of a hydrodynamic nature dealing with the vertical flow of gas-liquid mixtures in pipes, the two factors that present the greatest difficulty are the relative motion between the phases and the energy loss resulting from turbulence work. The former has generally been referred to in the literature as "slippage" and the latter as "fric-tion." A third factor of importance is the nature of admixture between liquid and gas for both the relative motion between the phases as well as the turbulence work are functions of the type of mixture. Although much work of a general nature has been performed on the vertical flow problem, there have been very few attempts made to study experimentally the factors involved in the phenomenon individually. Of these, perhaps the most notable is the work of Moore and Wilde1 on slippage. Some writers on the subject have assumed that over a wide range of operating conditions the controlling type of mixture, is one in which gas bubbles of uniform size are distributed throughout the liquid, and that the data obtained from experiments on the motion of single bubbles through various liquids may be used in evaluating the slippage. Ver-sluys2 has further assumed another controlling type of mixture in which the liquid occurs as a dispersed phase within the gas and applies data on the fall of drops of water in air to calculating the relative velocity. It was for the purpose of studying the applicability of data on single bubble motion to the slippage factor and to further observe the nature of mixtures that a research program was conducted at the University of California during 1932 and 1933. These experiments formed a basis for

Jan 1, 1935

By J. P. Newell, R. W. Storey

AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery .augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120 This head design proved to be very satis-

Jan 1, 1952

By John Birkinbine

IN the spring of 1878 the Pine Grove Furnace, located in Cumberland County, Pa., was blown in after lying idle for several years. The furnace was constructed in 1770, and for over a century it has been in almost continual operation. The plant consisted in 1877, when the writer was first called there, of a stone stack 32 feet in height, inclosing a shaft and boshes, the latter being 8 feet in diameter. The blast was supplied by two wooden blowing-tubs discharging into a third, having a floating piston sustaining a box weighted to give the desired pressure, the power being furnished by a waterwheel. A small 18-pipe hot-blast stove heated the blast. The furnace was remodelled during the winter of '77-78, and a Weimer blowing-engine with a blowing-tub 5 feet in diameter and 2 feet stroke, and the necessary boilers, were substituted for the wooden tubs and water-wheel. The stack was raised and enlarged, and provided with a bell and hopper having a central drop. Water dam and tymp were added, and general repairs were made. The hot oven, however, was riot increased. The furnace had always been operated with charcoal as fuel, and its reconstruction was made with a view to continue the use of charcoal, but provision was made for ample blowing capacity should other fuels at any time be employed. Although liberal arrangements had been made in cutting wood, the stock of charcoal supplied in 1878 was insufficient for the increased requirements of the remodelled plant, and notwithstanding the purchase of some 80,000 bushels from an adjacent idle furnace, there was riot enough to keep the furnace in constant blast until a new supply could be obtained, particularly as the season was unusually backward. Instead of following the established precedent of many charcoal furnace managers, i. e., blow out every February, it was determined to continue in blast, using coke as fuel. Accordingly, when the charcoal stock was exhausted, on March 22d, 1879, Connellsville coke was substituted, the change of fuel being made at once; that is, the coke charges followed immediately upon the last charcoal charges. After working a few days,-the strike in the Connellsville coke region cut off the supply, and anthracite coal was obtained, a mixture of the two fuels being employed. The strike continuing,

Jan 1, 1880

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the, limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By A. F. Taggart

THE following notes represent significant excerpts from a mass of records of experimental work done in the ore-dressing laboratory at the Columbia School of Mines during the years 1926 to 1928-inclusive. CLASSIFICATION OF EXPERIMENTAL WORK The experiments performed may be grouped for purposes of description under the following general -headings: I. Collecting agents. a. A method for quantifying collecting effect. b. Coating with undissolved collecting agents (oils) c. Action of dissolved collecting agents. II. Frothing agents. a. A method for quantifying frothing effect. b. Relation between frothing effect and chemical composition. III. Inorganic reagents. a. Methods of studying the effects of these reagents. b. Effect on slime dispersion. c. Effect on sulfides. SUMMARY OF THE ORIGINS OF PRESENT-DAY FLOTATION PRACTICE The first practicable, foolproof method of froth flotation was described in U. S. patent 835120, issued in 1906 to Sulman, Picard and Ballot, and in the equivalent patents in other countries. A number of less simple methods of producing the same result had been described previously in patent publications and otherwise.1 The reagents specified in all of these early patents were "oils" and, in addition, some inorganic substance, usually an acid. The quantities of reagents recommended and added were enormous when' compared with those used today.

Jan 1, 1929

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922

By S Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- [ ] fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941

By S. G. Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments [c] through g are more insoluble than lead carbonate, therefore should prevent the formation of lead carbonate on the galena surface. In experiment [i] the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments [j] through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941

By C. A. Rowland, R. C. Nealey

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The selection of dry grinding rod mills follows the basic principles established for the selection of wet grinding rod mills. The basic Bond Formulae1 [ ] is used to select mills when using grindability test results as the basis for selection. W is multi- plied by the 1.3 wet to dry grinding factor established from wet and dry ball milling experience, and then by any other applicable inefficiency factors.1 Dry grinding rod mills have also been selected by scaling up bench scale continuous rod mill tests and pilot plant tests.

Jan 12, 1968

By C. R. Sundeen, C. W. Nicolson, J. D. McAuliffe, C. A. Campbell, P. D. Pearson

SHAFT SINKING SYMPOSIUM is a weighty term that could mean any number of things. However, in, this case it has been possible to utilize the transcription of the Annual Meeting Session of the same title and present it in much the same manner as the experts on the panel presented it to their audience Wednesday afternoon, February 18, 1953, at the Los Angeles Statler Hotel.

Jan 8, 1953

[Alphabetic Section: The letter immediately following a member's name indicates grade: M-member, A-associate, J-junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary divisional affiliation: A. Mining & Exploration F. Coal B. Minerals Beneficiation G. Petroleum C. Iron and Steel H. Industrial Minerals D. Extractive Metallurgy J. Council of Education E. Institute of Metals K. Council of Economics Geographic Section: An asterisk (*) preceding a member's name indicates availability for consulting work:]

Jan 1, 1961

[Alphabetic Section (Page 729): The letter following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute o f Metals K-Council o f Economics]

Jan 1, 1961

[Alphabetic Section (Page 1): The letter immediately following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute o f Metals K-Council o f Economics]

Jan 1, 1961

[Alphabetic Section (Page 689): The letter immediately following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute of Metals K-Council o f Economics]

Jan 1, 1961

By R. T. Gallagher

FOLLOWING recent precedent, the Mineral Industry Education Division opened its first session on Sunday afternoon at the Columbia University Men's Faculty Club with an unexpectedly large attendance. The first session was presided over by the Division Chairman, A. F. Greaves-Walker. The first paper, a preliminary report on college enrollments in mineral technology curricula, by W. B. Plank, though incomplete, pointed to a general over-all reduction of 38 per cent in enrollment in mineral industry curricula. Following that, A. C. Callen's paper elicited many comments. It presented the results of a survey (no direct questions asked) addressed to officials in the mining industry. J. L. Bray spoke on war production drive methods and results and his slides gave visible evidence (and much laughter) of the success of the drive. C. L. Wilson's able presentation covered not so much present status but the future status of accelerated mineral technology programs after the war. The last paper of the first session by Edward Steidle, was handed out in mimeographed form.

Jan 1, 1943