Search Documents

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By AIME AIME

THE No. 9 mine of the Wheeling & Lake Erie Coal Mining Co., a subsidiary of M. A. Hanna & Co., at Fairpoint, Ohio, has normally produced about 1000 tons of coal daily for several years, but recently it was converted into an experimental mine to afford means of studying new methods and equipment under consideration for development and mining. Among other projects, the possibility of using a duck-bill, self- loading conveyor in driving entries, with a view of in- creasing the rate of progress where quick development is of importance was studied. Actual operation soon revealed that even though break-throughs are made ,every 60 ft., as required by the state mining laws, the :amount of natural Ventilation reaching the working face was not sufficient to supply the men and that in ,order to obtain a plentiful supply of pure. air and maximum efficiency and to avoid costly interruptions after shots, it was necessary to supply auxiliary ventilation by using Ventube and a Vano fan.

Jan 1, 1929

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By H. R. Banks

PONDERING the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote “Tho’ the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of, either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. PRINCIPLE OF BALL MILL The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely fine mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries, we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? METHODS OF GRINDING The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of fine grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1945

By Frank Corwin

It is the purpose of this article to give a brief account. of the experimental work and to show how the increase in efficiency was brought about. Part of the experimental work described in this paper was carried out by the writers, while in the employ of the Anaconda Copper Mining Co., under the direction of M. W. Krejci, Metallurgist, and Arthur Crowfoot, Chief Sampler. Complete records of all of the MacDougall testing work have been placed at our disposal through the courtesy of A. E. Wheeler, Superintendent. II. BRIEF HISTORY OF PRESENT MACDOUGALL PLANT. The first change from the Brueckner cylinders used for roasting concentrates at Great Falls was the construction of a MacDougall roaster of the Herreshoff type. This furnace was first started on June 15, 1898. It bad eight hearths, was lined with fire brick, and had an air-cooled central shaft, but no provision was made for cooling the rabble arms. It was operated for a while, and accomplished the work of roasting, but ran so hot that the rabble arms became twisted and distorted out of shape. To prevent the furnace from becoming too hot a device was then installed to draw the heated gases away from the hearths. This consisted of a pipe connected to alternate hearths of the MacDougall furnace and also connected to the flue. It was equipped with dampers, 'so that the hot gases could be drawn away from any one of the alternate hearths directly into the flue.

Jan 7, 1913

By Frank Corwin

I. INTRODUCTION. SINCE the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 7, 1913

By E. V. Foran

The repressuring of oil-producing formations during the flush stage of production, although requiring primarily the same procedure as operations on formations where the gas pressure has been depleted, offers several advantages of major importance, the value of which has not heretofore been demonstrated. It is the purpose of this paper to present an account of some recent operations of this character and the economic effects on the properties where they were applied. The principal objective in all repressuring operations is to secure an effective diffusion of the input energy to all parts of the producing sand. If this can be accomplished, success is assured during the remainder of the life of the property; if not, it will be temporary only and will be followed by difficulties, .and the maximum possible recovery will not be obtained. During the past year in Texas, the Cook pool in Shackelford County, and the Turbeville pool in Archer County, while still in their flush stage of production, have been subjected to repressuring operations to observe their reaction to this process during the early stage of their productive periods. The repressuring operations carried on in each of these pools will be discussed separately in this paper in order to show peculiarities which were present in one pool but were not observed in the other. Turbeville Pool The Turbeville pool is in Archer County, about 30 rniles south of Wichita Falls. The productive sand varies in thickness from 10 to 30 ft., the average being about 16 ft. The depth of the sand varies from 1450 to 1530 ft. The developed productive area to date is approximately 200 acres, but the limits of the pool have not yet been proved. The sand varies considerably in different parts of the pool with respect to both porosity and permeability. The gravity of the oil varies from 39 to 41° A. P. I. There were some wells which flowed for a few days after completion but during 1927 all production was secured by pumping. The

Jan 1, 1928

By E. H. Fahmy, L. C. Uren

During recent years, oil producers have observed with interest the practical success which has attended the application of water as a medium for displacement of oil from its reservoir sands in the Bradford field of northern Pennsylvania and southern New York. Here, according to various authorities, additional recoveries of frorn 2,000 to 12,000 bhl. of oil per acre have heen secured by this method, after ordinary flowing and pumping. rnethods of production had practically reached the lower limit of economic operation. Notwithstanding the success which has attended the practical use of the flooding process in the Bradford field, oil producers in other regions are skeptical of its value when applied under physical conditions differing markedly from those which characterizc the Bradford field. Its usc would probably he construed as illegal in most of the oil-producing states. This general relnctance on the part of oil producers in other regions to accept the flooding process is due in large part to lack of infor-n~ation regarding the factors that influence its operation and efficiency. With the purpose of clarifying to some extent the issues involved, and of determining when the flooding proccess may or may not beeffee-tivcly ernployed, the writers have conducted a serics of laboratory exper-imentments under carefully controlled conditions, designed to indicate, the influence of various physical, chemical arid lithologic factors. These experments have not been conducted under conditions identical with those which exist at depths far below the earth's surface, so that direct quantitative comparisons with field results are not justified, hut it is believed that the experimental results at least warrant qualitative inter-pretations that may he applied to field conditions. The methods employed in the conduct of these experiments are briefly explained, and the results, together with the conclusions based thereon, arc presented. FactoRs Influencing Displacement of Oil froM SaNdS by WAteR- flooding Before presenting the experimental data, it, will he desirable to con-sider the manner in which the residual oil is retained within the oil sand

Jan 1, 1928

By A. H. Bell

The results of repressuring (or gas-drive) have been very encouraging to the several companies doing experimental work along these lines in California. The most notable examples are the Shell and the Union Oil companies at Dominguez, the Marland Oil Co. at Seal Beach, and the California Petroleum Corpn. at South Mountain. The results of the Marland test at Seal Beach are interesting in that re pressuring was started while several wells were still flowing; also, on account of the high pressures required to overcome the hydrostatic pressure exerted by high-head edge water. The well first chosen for repressuring is about halfway up the flank of the structure and had been on the beam making about 250 bbl. of fluid daily, cutting about 60 per cent. emulsion. The fluid lcvel was 230 ft. from the surface and the top of the sand was 4393 ft. Tubing was run to 4000 ft. with a packer and the space above the packer was filled with water to balance the high pressures. Gas was started in slowly to allow the fluid to be pushed back into the sand, and required three days at a pressure of 1500 Ib. per sq. in. before starting into formation. The pressure was once built up to 1800 Ib. and the compressor was shut down for a few hours. When again started, the well took gas at 1500 Ib., and after about three weeks the pressure was dropped to 1450 Ib. The present pressures required range between 1400 and 1450 lb. Volumes as high as 1,500,000 cu. ft. per 24 hr. were put into the well. Increases as high as 50 per cent. in production were obtained in wells up-structure with very little increase in wells down-structure. Also, the water cut on one edge well materially decreased. After about 40 days the repressuring was moved to two wells farther down-structure and the well originally repressured was put on production. The result of this was a great increase in the production of wells one location farther down-structure, a rapid increase in one well one location up-structure, and a decrease in production of the wells farthest up-structure. Later the gas started to short-cut to the nearest well down-structure, nullifying to a certain extent the effects of the repressuring work. The increased production that could be definitely attributed to the repressuring work

Jan 1, 1928

By C. R. Fettke

In 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northwest of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and LUX. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J. Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey. Stratigraphic Position of the Producing Sand The producing sand at Hamilton Corners is encountered at depths of from 364 to 560 ft., depending on the location of the well and the topog-

Jan 1, 1928

In December, 1927, the Institute published two papers on the Brad-ford pool, which were presented at the New York meeting in 1928. Pamphlet copics may be obtained by writing to the Secretary's office for: Oil-field Waters of the Bradford Pool, by Paul D. Torrey. Technical Publicalion No. 38. Some Factors Influencing Production of Oil by Flooding in the Bradford and Allegany Fields, by Paul D. Torrey. Technical Publicaliol No. 39.

Jan 1, 1928

By I. M. Roberts

THE war emergency has affected every phase of industry. The gas and coke-oven companies have sought faithfully to discharge their responsibility in this critical period and have willingly modified their operations where possible to meet the ever increasing demands made upon them. Our company made commitments for blast-furnace coke for war purposes which necessitated a reduction in coking time in order to produce the amount required to. meet the new demands. At the same time there were certain customers of long standing, who had been supplied with foundry and egg-sized coke produced on fairly long coking periods, who also were engaged in war work and whose patronage we desired to retain. Coke produced on short coking rates from the coal mixture we were then using would not have been satisfactory for these customers. The average width of our ovens is 19 ¾ in., which is a little wider than the more modern ovens of the present day. They were originally designed to give somewhat cool tops in order to produce a rich gas. This necessitates carrying the heats a little on the warm side so that the tops will be fully carbonized. A reduction in coking time, as is generally known, is accompanied by a reduction in the average size of the coke produced. This is due to the greater shrinkage that takes place at the higher temperatures required to carbonize the charges in a shorter time. The net result is that the coke is more cross fractured and longitudinally fractured and breaks up into small sizes on handling. The cokes produced from the better coking coals seem to be more susceptible to fracture at high temperatures than those from poorer coking coals. A coal mixture that produces a beautiful foundry-sized coke at 30 to 36 hr. may yield a product at 18 hr. that would be so badly fractured as to be unsatisfactory for foundry practice. COKING CHARACTERISTICS OF COALS Our problem was to find some economical innovation and develop a method that would enable us to reduce the coking time and still produce a coke satisfactory to our foundry trade. However, before discussing the results of our present operations, it might be well to present a few observations on the coking characteristics of coals in general. Most coke-oven operators carbonize a blended mixture of coals. It may consist of a single high-volatile coal with a single low-volatile coal, or of a combination of several high-volatile and low-volatile coals. Medium-volatile coals of the Eagle seam are used for the production of high-grade foundry coke. Medium and high-volatile coals are often blended with one or more low-volatile coals. The possibilities are almost infinite, but the combinations are limited by such factors as cost and facilities for handling multicoal mixtures, and by other practical considerations. Every coal has characteristics that make it blend better with a particular coal or coals in preference to others. This property has

Jan 1, 1944

By C. C. Wright, R. J. Day

ALTHOUGH data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buck- wheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths-a few inches long-as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced. This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organizations-individually, together, and in co- operation with other interested groups- have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop

Jan 1, 1948

By Mark E. Emerson

INTRODUCTION A long time has passed since geologists encountered encouraging mineralization in their regional exploration program for base metals deposits. Detailed drilling during the following two field seasons served to delineate the configuration of the deposit. Various statistical techniques were employed to provide confidence levels regarding the extent of the reserves and to categorize them according to whether proved, indicated or inferred. At this juncture, it appears that the company has an orebody. Time elapsed? - three years; money spent? - $2.5 million. Much remains to be done before the orebody becomes a mine. The company urgently needs to develop new orebodies to replace its existing mines which are being depleted. It therefore has expended sizable amounts in exploration, the life blood of the company. A staff of specialists is maintained to evaluate new projects and to conduct feasibility studies. The scale of new mining projects today is beyond the resources of most mining companies. Bank financing, therefore, is often vital if the company is to survive. The following scenario describes how a company goes about evaluating mine projects and what is needed to meet lender's criteria in securing the needed financing. MINE PLANNING Now that the company engineers have taken over the project, their concern is no longer with finding ore but in developing it. An exploration shaft has been put down and a tunnel driven into the orebody to verify, on a large scale, what has been seen so far only in pencil- like drill cores. A large tonnage bulk sample is mined and shipped off to an independent metallurgical process laboratory for beneficiation testing. The budget is expended to cover engineering studies. Preliminary capical and operating costs are developed in- house and profitability studies are made based or1 assumptions concerning the markets for the main product and the indicated gold, silver, and other by-products. Time elapsed? - four years; cost to date? - $3.5-$4.5 million. The staff prepares its own pre-feasibility study. After review, the Executive Committee authorizes management to proceed with full-scale studies. The task is to make preliminary designs and to develop definitive capital and operating cost estimates. Specialized consultants will be engaged to study slope stability for the open pit and rock strength if underground recovery proves more feasible. If it is near the sea, an oceanographic report might be commissioned to see if the tailings can be disposed of off shore. Environmental impact studies are commissioned from a firm familiar with government requirements and regulations in this important area. The company subscribes for an expensive multi-client study of the supply- demand-price outlook for the product to support its own long-range price forecast. Now all the numbers are available to make a definitive appraisal of the value of the project. Cash flow analyses and sensitivity studies follow. Reams of computer printouts are generated. Time elapsed: five years. Amount spent? - up to $9 million, depending on the size, complexity and attractiveness of the project. Marginal projects always take longer. Finally, an engineering and construction (E&C) company is given the task of integrating and compiling all the data into a feasibility study. The results of dozens of reports, memoranda, computer printouts, and charts are boiled down to one final summary report of a few hundred pages together with conclusions and recommendations. After thoughtful review at a board meeting, the directors authorize management to proceed with detailed engineering work - provided that

Jan 1, 1985

Jan 1, 1923

Jan 1, 1938

Jan 1, 1936

Jan 1, 1936

Jan 1, 1936

Jan 1, 1940