Search Documents

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By F. D. Hoyt, H. L. Hartman

The development of new processes and methods by The Pennsylvania State University to improve slate quarrying technology has centered in recent years on cutting and sawing stone in the quarry to eliminate a second cutting process in the mill. Two machines exhibit promise for this work: 1) a circular saw mounting diamonds or hard inserts to produce smaller sizes of stone and 2) a chain saw with insert cutting teeth to produce stone in the larger dimensions. Prototype machines have been constructed and tested in several Pennsylvania slate quarries, and one commercial installation has been operated for several months with a circular diamond saw. Other kinds of dimension stones may be cut by these saws. Research at Penn State has begun to study the fundamental cutting action of rotary tools or saws in slate and other dimension stones. A laboratory drill press is being instrumented to permit thrust-torque-rotational speed us penetration rate studies of single tooth cutting surfaces on stone. Machinability studies of slate conducted with tungsten-carbide inserts have been performed. The dimension stone industry generally accepts the rather basic premise that the larger the block removed from the quarry, the more practical and economical the operation. Thus, the concept of cutting to size any dimension stone while it remains in place in the parent bed would receive little consideration from the majority of members of the industry. However, the slate industry, which is usually considered a separate member of the dimension stone family, is pioneering in the development of an in-place sawing method. Before any final decision can be reached concerning a proposed new system, it is essential to take a long, hard look at the present method of operation in order to determine if the new system is indeed an improvement or even desirable. In the following section is a brief description of present quarry practice in the slate quarries of eastern Pennsylvania. PRESENT METHOD OF QUARRYING SLATE In the numerous slate quarries of Lehigh and Northampton Counties of Pennsylvania, the grain and cleavage of the slate are most often at right angles to each other; if a third surface is broken at right angles to these two natural planes of weakness, blocks of more or less rectangular shape can be separated.' In conventional quarrying a large calyx core drill prepares holes of 36-in. diam in which wire-saw standards are positioned. By wire sawing between strategically located core-drill holes, large sinks or benches of virgin slate are opened up. The sides freed by wire sawing will vary from quarry to quarry but generally are rectangular in shape with dimensions averaging 20 ft in length and about 15 ft in depth. Some quarries are fortunate in having a joint or natural parting to work to, which of course diminishes the amount of core drilling and wire sawing required. Once the various benches have been developed either through wire sawing alone or through a combination of wire sawing and natural jointing planes, the block removal proceeds in the following manner. A plug hole is drilled in the block with a compressed-air hammer and a feathering chisel is inserted in the hole to cause a fracture of the rock either with or against the grain as indicated by the positioning of the so-called feathers. This operation is referred to as sculping. After a block has been freed with and against the grain by means of wedging from the cross fracture with long bars or levers, the block is further freed along the cleavage plane by shimming it up with small wooden pieces in an operation known as styling. A large steel loading chain is wrapped around a block thus freed and the chain is attached to the wheel of an overhead cable. The block is then hoisted vertically to the cableway and moved along this cableway laterally to the lip or edge of the quarry. From here it is unloaded onto a rail car or truck for transportation to the processing mill. Except for occasional blasting to free stubborn blocks,

Jan 1, 1961

By W. M. Phillips

Processing kaolin clays from the sedimentary deposits of Georgia and South Carolina is described in this article. While the major processing steps are touched on briefly, emphasis is given to the dewater-ing of the clay-water slurries (slips) formed in the processing of kaolin clays. The dewatering steps discussed include gravity settling, centrifugal dewatering, vacuum filtration and thermal drying. Particular attention is given to vacuum filtration and the variables affecting filtration of these kaolin clays. Kaolin consists essentially of the mineral kaolinite, which is a hydrated aluminum silicate (Al2O3 . 2SiO,). Commercial deposits of kaolin occur in several areas of the U. S., but approximately 90% of the kaolin produced in this country comes from Georgia and South Carolina. These deposits are of sedimentary nature and occur in a geological fall line in the Tuscaloosa formation at elevations between 300 and 450 ft above sea level. Over two million tons of kaolin clays are used by industry in the U. S. each year. A big percentage of this tonnage is used in the paper industry for coatings in making glossy and high quality grades of printing papers. In addition, large tonnages are used as pigments; as fillers for rubber, plastic and fertilizers; and in ceramics. Properties of kaolin that make it widely used in the above applications are its particle size fineness, natural whiteness, chemical stability and non-abrasiveness. In addition to these desirable properties, it is relatively inexpensive. The finer coating grades of clays range in price from $15 to $28 per ton while the coarser filler grades sell within a range of $7 to $13.50 per ton. Pure kaolin particles are small hexagonal flat platelets. Above the 2-p size, the particles usually consist of stacks of plates, while below the 2-p particle size they occur as individual flat, hexagonal plates. Since these individual platelet particles provide the most desirable coating and flow characteristics, major importance is given to particle size fractions of 2 p and smaller. Generally, coating grade clays are those with all particles smaller than 15 p and at least 70% of the particles less than 2p. These coating grades also have 50% or more of the particles smaller than 1 µ in size. The extremely fine grades of coating clay currently being produced approach the range of 100% smaller than 2p. The filler grades of kaolin have 100% of the particles passing 325 mesh but have less than 70% of their particles below the 2-p range. Fig. 1 is a schematic representation of the major processing steps involved in preparing kaolin clays for marketing. MINING All kaolin mining is open pit. The ratio of overburden to clay will average 3:1, but this ratio can, of course, be much higher depending upon the grade of the clay and the size of the deposit. Most of the commercially mineable deposits occur from 20 to 120 ft below the ground surface. Both draglines and pans are used in removing the overburden and mining the clay deposit itself. After mining, the most common method of transporting the clay to the processing plant is by blunging or re pulp-

Jan 1, 1963

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963

By R. B. Porter, R. P. Porter, R. A. Lothrop

Changes became necessary in dredging methods employed in Idaho through passage of the Dredge Mining Protective Act (1954). Among other provisions, the law requires dredge operators to construct settling ponds of sufficient capacity and character to reasonably clarify the water used in the mining process before such water is discharged into the stream. Porter Bros. Corp., a placer mining company with many years operating experience in Oregon and Montana, became interested in strategic mineral placers in Idaho in 1950 when it was learned that prospectors had discovered a radioactive mineral deposit in Bear Valley Creek, 95 miles northeast of Boise. The company acquired mining leases and proceeded with exploration and development work on the property. After extensive research had resulted in the determination of successful separation processes, contracts were negotiated with the federal government and deliveries of columbium-tantalum and uranium concentrates commenced in 1956. The mining operations are located in a primitive area of Idaho among salmon spawning grounds and crystal-clear mountain trout streams. To avoid involvement in a very controversial issue, it appeared advisable for the company to develop water treatment procedures exceeding those requirements stated in the Idaho Dredge Mining Protective Act. Operation: The company operates one 6 cu ft continuous bucketline dredge and one 4 1/4 cu ft continuous bucketline dredge on the property. The dredges are jig-equipped, with feed being screened to 3 in. by trommels. The screening and gravity concentration methods satisfactorily separate the heavy minerals from companion clays, sand, and gravel. However, this separation of the heavy minerals requires water from the dredge pond with a minimum content of silt and colloids; therefore, water for dilution is added continuously to the dredge pond to suppress solids buildup. Discharge of this highly turbid water to maintain the proper pond level would ultimately result in an excessive silt load in Bear Valley Creek. To prohibit the turbid pond water from flowing directly into Bear Valley Creek, it was necessary to isolate the dredging area. Main by-pass canals were constructed along each side of the dredge pond and numerous secondary canals were dug for diverting seepage and snow runoff. One by-pass canal, extending more than two miles along the west side of the valley, diverts the main stream as well as tributaries entering from the west; a canal east of the dredge area diverts streams entering from that direction. At the beginning of operations in 1956, the dredge pond effluent was filtered through tailings and settled by use of coagulents in a series of lagoons. The filtrate was then discharged directly into the stream. Although this procedure gave satisfactory results in conformance with the state law, ice buildup and lagoon freezing hindered the efficiency of the process during periods of low temperature. For this reason, testing began in 1956 on a water treatment process that would operate efficiently under the extreme weather conditions encountered in Bear Valley. Development of Water Treatment System: Porter Bros. Corp. established the following requirements for effective continuous treatment of dredge pond effluent to the stream which, at low flow conditions, effluent to the stream which, at low flow conditions, would not result in a turbidity exceeding 25 ppm in the stream, 2) produce a sludge sufficiently dense to minimize disposal area requirements, 3) be semi-portable to follow dredge movements, 4) be capable of operating at low temperatures, and 5) be capable of handling a variety of capacities and turbidities.

Jan 1, 1961

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,' the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson's investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.'s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By V. T. Stringfield, H. H. Cooper

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson' who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson's knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida. More recent reports give the results of investigations that have been in progress in cooperation between the Florida Geological Survey and the U. S. Geological Survey since 1930. As a result, the ground-water geology and hydrology of Florida are now so well known that ground-water problems such as confronted early investigators no longer exist. However, new problems arise and new discoveries are made as the demand for more ground water increases with the development of the State. Water-Bearing Formations Descriptions of the geologic formations and a map showing their distribution at the surface are given in a recent report by Cooke.' The geologic formations that yield the ground-water supplies in Florida represent only a small part (about 1000 ft) of the total thickness of the sedimentary rocks (more than 15,000 ft) that underlie Florida. The water-bearing rocks that yield fresh water include more than two dozen formations that range in age from Eocene to recent. The Eocene formations, which consist chiefly of limestone, are the oldest and the deepest of the formations in Florida that yield fresh water to wells. In 1944, on the basis of a study of the foraminifera, the Applins -ivided the limestone of Eocene age into six formations, which are as follows, from top to bottom: Age or group Formation Jackson Ocala limestone icAvon Park limestone Claiborne -j Tallahassee limestone aLake City limestone Wilcox Salt Mountain limestone xOldsmar limestone The Ocala limestone and the underlying formations of Claiborne age, along with some of the overlying limestone of Oligocene and Miocene age, constitute the principal source of water in Florida and southeastern Georgia and generally may be regarded as forming one artesian aquifer or water-bearing unit. This aquifer is referred to in this paper as the Floridan aquifer, a name proposed by Parker.' In part of Seminole County alone more than 1000 flowing wells yield water from the Floridan aquifer. A yield of 6500 gpm, or about 9.5 million gal per day, by natural flow from a well penetrating the aquifer at Jacksonville, Florida, was observed in 1942. A yield of about 7000 gpm by natural flow was reported for a well 1390 ft deep at St. Augustine in 1887. The largest yield reported from a pumped well penetrating the aquifer is 7500 gpm, or about 10.5 million gal per day. The aquifer is also the source of some of the large springs, such as Silver Springs, whose discharge, according to measurements made by the U. S. Geological Survey, has ranged from 526 to 1350 sec-ft, or from 340 to 872 million gal per day. The top of the Ocala limestone, as represented by contours in Fig. 1, indicates in a general way the geologic structure of the formations that comprise the Floridan aquifer. The Ocala is at or near the surface in the areas represented by shading in the northwestern part of the peninsula and also in an area in western Florida adjacent to Alabama and

Jan 1, 1952

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By Roscoe E. Bell

BETWEEN 1945 and 1948 the author made studies of the western phosphate industry and its potentialities. These included an appraisal of the opportunities for western development of the industry, studies of production costs, of market potentials, of transportation economics, and of industry location. This paper will be directed toward pointing up the factors which have an important bearing on the establishment of fertilizer plants in the western area. Industry Location Factors: There are, of course, an infinite number of possible organizational setups which might require consideration. However, the phosphate industry is simple enough so that studies of the most probable alternatives can be made conveniently. The salient factors which require special consideration in such a study are: (I) the location of the raw materials, (2) the location, size, and character of the present and potential markets, (3) the location of energy sources and materials required for fertilizer processing, (4) the location and capacity of present manufacturing facilities, (5) the cost of assembling the materials and energy needed in manufacturing, and (6) the cost of distributing the manufactured product. Raw Material Supplies: Rock phosphate is the raw material for the manufacturing of phosphate fertilizer. In the United States the important known deposits of this material are located in three general areas (fig. 1). The western deposits, comprising about 60 pct of the nation's supply, are in the four-state area—Idaho, Wyoming, Utah, and Montana. The Florida deposits comprise roughly 38 pct of the national supply. The Tennessee deposits, comprising about 2 pct of the national supply, have been the most important source until recent years. The western deposits, which are virtually undeveloped, have not been used to any extent to meet the nation's need for phosphate rock and phosphate fertilizer. Fertilizer Markets: The large national markets for fertilizer are in the midwestern and eastern United States (fig. 2). The principal far-western markets are along the Pacific Coast, especially in California. Until recent years the western markets have been extremely limited, whereas the markets in the eastern United States have long been established and manufacturing facilities have been provided to meet these needs (fig. 3). In recent years the western markets have expanded very rapidly, continuing to grow throughout the war years and postwar period at a similar rate. The question always arises as to whether this is a temporary war-swollen market which will shrink back to its original size as soon as the present agricultural price levels drop. In order to answer this question consideration must be given to the character of the market (fig. 4). I have considered seventeen western and midwestern states in the western market area where transportation costs from the western deposits are equal to or lower than those from Florida. They include all states west of a line drawn through Chicago, Kansas City and the western boundary of New Mexico. In the mewar period this was a small market totaling only 37,000 tons of P,O, annually. The 1946 total for this same area was approximately 200,000 tons. Considerably more fertilizer would have been used in 1946 had adequate supplies been available. Estimates of future markets are difficult to make, but we do have some indices that are useful. The

Jan 1, 1951

By Roscoe E. Bell

BETWEEN 1945 and 1948 the author made studies of the western phosphate industry and its potentialities. These included an appraisal of the opportunities for western development of the industry, studies of production costs, of market potentials, of transportation economics, and of industry location. This paper will be directed toward pointing up the factors which have an important bearing on the establishment of fertilizer plants in the western area. Industry Location Factors: There are, of course, an infinite number of possible organizational setups which might require consideration. However, the phosphate industry is simple enough so that studies of the most probable alternatives can be made conveniently. The salient factors which require special consideration in such a study are: (I) the location of the raw materials, (2) the location, size, and character of the present and potential markets, (3) the location of energy sources and materials required for fertilizer processing, (4) the location and capacity of present manufacturing facilities, (5) the cost of assembling the materials and energy needed in manufacturing, and (6) the cost of distributing the manufactured product. Raw Material Supplies: Rock phosphate is the raw material for the manufacturing of phosphate fertilizer. In the United States the important known deposits of this material are located in three general areas (fig. 1). The western deposits, comprising about 60 pct of the nation's supply, are in the four-state area—Idaho, Wyoming, Utah, and Montana. The Florida deposits comprise roughly 38 pct of the national supply. The Tennessee deposits, comprising about 2 pct of the national supply, have been the most important source until recent years. The western deposits, which are virtually undeveloped, have not been used to any extent to meet the nation's need for phosphate rock and phosphate fertilizer. Fertilizer Markets: The large national markets for fertilizer are in the midwestern and eastern United States (fig. 2). The principal far-western markets are along the Pacific Coast, especially in California. Until recent years the western markets have been extremely limited, whereas the markets in the eastern United States have long been established and manufacturing facilities have been provided to meet these needs (fig. 3). In recent years the western markets have expanded very rapidly, continuing to grow throughout the war years and postwar period at a similar rate. The question always arises as to whether this is a temporary war-swollen market which will shrink back to its original size as soon as the present agricultural price levels drop. In order to answer this question consideration must be given to the character of the market (fig. 4). I have considered seventeen western and midwestern states in the western market area where transportation costs from the western deposits are equal to or lower than those from Florida. They include all states west of a line drawn through Chicago, Kansas City and the western boundary of New Mexico. In the mewar period this was a small market totaling only 37,000 tons of P,O, annually. The 1946 total for this same area was approximately 200,000 tons. Considerably more fertilizer would have been used in 1946 had adequate supplies been available. Estimates of future markets are difficult to make, but we do have some indices that are useful. The

Jan 1, 1951

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of byproduct materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals. Development of the Industry The industry developed to commercial stature in Pennsylvania largely because of the presence of beds of ocher extending from Easton in a southwesterly direction toward Reading, and a variety of small iron mines in the region. The mining of paint ores in the Lehigh Valley was active as early as 1850 and shortly after the Civil War the establishment of mills expanded production and led to the development of new products and eventually the manufacture of synthetic pigments. Pennsylvania continues to maintain it.s leadership as a producer of mineral colors. Production is recorded also in New Jersey, Illinois, Virginia, Ohio, and Georgia. Iron as a Pigment Iron in various compounds is the most important pigment in nature. The iron pigments are characterized by stability, light fastness, good covering power, high index of refraction, and economy in production. Ferrous compounds display a typical green coloration. This has not been employed as a commercial pigment to any great extent except incidentally in such greenstones as have been used in construction, or crushed and sized for application as a granule to roofing. Ferric oxides are characteristically red and form an important group of industrial pignents. Hydrated ferric oxides exhibit various shades of yellow and are present in such familiar pigments as ocher and sienna. The addition of small amounts of manganese oxide or carbon as organic matter to the yellows produces the brown umbers. Magnetite is one of the few black minerals that grinds to a black powder. The mineral pigments vary from earth colors of low intensity and great dilution of iron content to almost pure iron compounds with high tinting strength and correspondingly greater value. There has been some relationship between the mining of iron ores and the production of mineral pigments; although the production of colors is not carried on appreciably as a byproduct of iron mining. A number of mineral pigment producers, particularly in the eastern states, have operated mines which in the past were small producers of hematite, bog ore, or carbonate ore. The knowledge of the location of the deposit and its possibilities as a producer of pigment are due to its past history as a producer of metallic ore. Many iron compounds may be changed in color by calcination, the end product being Fe2O3, a stable red oxide. The yellow hydrated oxides may be changed to red. The gray carbonate, found in Carbon County, Pa., calcines to a fine red product. Ferrous sulphate (copperas) often available in tonnage as a byproduct of the steel industry, breaks down under heat or chemical action leaving a residual red oxide. Pigments produced by calcination or dissassociation of compounds possess the advantage of fine particle size and ease of grinding. Mineral Pigments MINERAL BLACKS Many black minerals grind to a light colored powder. This characteristic is familiar to the mineralogist as the white streak produced by a black

Jan 1, 1950

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By Randolph C. Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments. Survey: The pebble rock phosphate mining and washing operations in Florida (fig. 1) are along the river basins of the Alafia to the west and the Peace to the east. The elevation of the area varies between 40 and 170 ft above sea level. Effluents from the operations find their way into one of the two river systems (fig. 2), the Peace River which flows into Charlotte Harbor and the Alafia into Tampa Bay, both along the Gulf of Mexico. There are no major industries along these rivers below the phosphate operations. On the Peace River, the town of Arcadia, approximately 50 miles below the phosphate operations, obtains its water from the river. No other communities along the rivers use them as a source of water supply. Small communities, farms, and ranches are located along the rivers and both rivers drain vast swamp areas. Complaints had been received at the office of the Chief Sanitary Engineer, of the Florida State Board of Health,' that both rivers were turbid at various times and that fishing in the Alafia River was "not as good as it used to be." Tests made by another agency on the dissolved oxygen content of the Alafia River revealed that the oxygen content, at times, was comparatively low.= However, it was not shown that the phosphate wastes had any effect upon the oxygen content of the stream. The river waters are normally brown in color due to drainage from vast swamp areas and are very shallow, from 2 to 6 ft in depth. Turbid waters have been noted in streams coming from the present phosphate operations and also from streams along which there are no operations at the present time. It was learned from "old timers" that, when many more companies than at present were operating along both the Alafia and Peace Rivers forty or fifty years ago, no attention was paid to prohibiting the disposal of slimes along the river basins. During dry periods now in some of the river swamps where drainage ditches have been dug, it is indicated clearly that phosphate slimes were disposed of directly into the river swamps for many years past. Places have been observed where there were alternating strata of phosphate mud, leaf mold, and quartz sand. The former practice of indiscriminate disposal of wastes accounts for some turbidity, particularly after heavy rains and washouts and during clearing of land and digging of drainage ditches. During a six months' period in which a large tract of land was being cleared and drainage ditches dug, a small stream (Six Mile Creek), which previously had been clear, showed a turbidity of 600 ppm and remained turbid until the clearing was completed; after which the stream again flowed clear. An interview with the operator of the municipal water plant, which is about 50 miles below the phosphate operations on the Peace River and which used this river as a source of supply, revealed that there had been no taste in the water for the past ten years, other than that occasionally encountered from increased growth of algae. The operations of each of the cooperating com-

Jan 1, 1951

By Randolph C. Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments. Survey: The pebble rock phosphate mining and washing operations in Florida (fig. 1) are along the river basins of the Alafia to the west and the Peace to the east. The elevation of the area varies between 40 and 170 ft above sea level. Effluents from the operations find their way into one of the two river systems (fig. 2), the Peace River which flows into Charlotte Harbor and the Alafia into Tampa Bay, both along the Gulf of Mexico. There are no major industries along these rivers below the phosphate operations. On the Peace River, the town of Arcadia, approximately 50 miles below the phosphate operations, obtains its water from the river. No other communities along the rivers use them as a source of water supply. Small communities, farms, and ranches are located along the rivers and both rivers drain vast swamp areas. Complaints had been received at the office of the Chief Sanitary Engineer, of the Florida State Board of Health,' that both rivers were turbid at various times and that fishing in the Alafia River was "not as good as it used to be." Tests made by another agency on the dissolved oxygen content of the Alafia River revealed that the oxygen content, at times, was comparatively low.= However, it was not shown that the phosphate wastes had any effect upon the oxygen content of the stream. The river waters are normally brown in color due to drainage from vast swamp areas and are very shallow, from 2 to 6 ft in depth. Turbid waters have been noted in streams coming from the present phosphate operations and also from streams along which there are no operations at the present time. It was learned from "old timers" that, when many more companies than at present were operating along both the Alafia and Peace Rivers forty or fifty years ago, no attention was paid to prohibiting the disposal of slimes along the river basins. During dry periods now in some of the river swamps where drainage ditches have been dug, it is indicated clearly that phosphate slimes were disposed of directly into the river swamps for many years past. Places have been observed where there were alternating strata of phosphate mud, leaf mold, and quartz sand. The former practice of indiscriminate disposal of wastes accounts for some turbidity, particularly after heavy rains and washouts and during clearing of land and digging of drainage ditches. During a six months' period in which a large tract of land was being cleared and drainage ditches dug, a small stream (Six Mile Creek), which previously had been clear, showed a turbidity of 600 ppm and remained turbid until the clearing was completed; after which the stream again flowed clear. An interview with the operator of the municipal water plant, which is about 50 miles below the phosphate operations on the Peace River and which used this river as a source of supply, revealed that there had been no taste in the water for the past ten years, other than that occasionally encountered from increased growth of algae. The operations of each of the cooperating com-

Jan 1, 1951

By M. R. Geer, H. F. Yancey

THE performance of coal-washing equipment, that is, the effectiveness with which coal and impurity are separated, is a subject of undisputed interest to all concerned with the preparation of coal. Through the years much has been written in both American and European literature on the performance of coal-washing equipment and its interpretation, but until recently no effort has been made to consolidate this wealth of information into a single, comprehensive treatment of the subject. A splendid effort in this direction was made at the First International Conference on Coal Preparation held in Paris in June 1950 in which representatives from virtually every coal-producing country participated. Although the scope of the conference covered the entire field of coal preparation, many of the sixty-odd papers and a great deal of the discussion dealt with the subject of evaluating washery performance. Prominence was given this subject by the Centre d'Etudes et Re-cherches, des Charbonnages de France, which sponsored the conference. This research organization, generally referred to as Cerchar, was formed in 1948 following the nationalization of the French coal industry. Since that date it has conducted an intensive study of coal preparation. Perhaps because of a fresh viewpoint, Cerchar realized immediately that complete information on the performance of French washeries and a thorough understanding of the mechanism of gravity separation were the fundamental prerequisites in a program to improve preparation practice. For this reason Cerchar concentrated on obtaining performance data and on a comprehensive study of methods of evaluating such information. Some idea of the magnitude of this work will be appreciated from the fact that 175 performance tests were made in 44 plants. The work performed by Cerchar emphasized a condition that is recognized by many of those concerned with coal preparation, namely that the lack of uniformity in presenting data on washery performance, the diversity of methods used in evaluating such information, and the frequent confusion of the terms related to performance have been prime factors militating against the progress from art to science. Thus, Cerchar feels that standardization of the methods employed for evaluating washery performance, not only in France but in the entire world, is essential to progress, and the prime objective of the Paris conference was to seek international standardization of the evaluation methods advocated by Cerchar. At the conclusion of the conference the question of standardization was referred to the International Standards Organization. A careful study of the dozen papers on the subject of evaluating washery performance presented at the conference reveals that none of the methods is new; most of them date back over a decade. Nevertheless, the intensive scrutiny of these methods brought about by the conference unquestionably has resulted in a valuable exchange of ideas and a clarification of thought that could scarcely be achieved in any other way. The object of the present report is to make available to the American coal industry the ideas developed at the conference which seem most important from an American viewpoint and to provide a critical analysis of some of the evaluation methods advocated by Cerchar. The various methods of evaluating washery performance are illustrated partly with data that have been published in American literature, and some new data have been obtained as the result of experimental work undertaken since the conference to provide information on certain controversial points. An English translation of the proceedings of the conference, including the discussion as well as the papers, will be available,' and previous to the conference Coal Age2 published a very brief description of some of the principal evaluation methods used by Cerchar. Americans will appreciate as well as do the French the desirability of standardizing both the termi-

Jan 1, 1952

By M. R. Geer, H. F. Yancey

John Grifien (Pittsburgh)—I wish to congratulate the authors on this paper, which, I am sure, will promote a clearer conception of the various criteria which have been advanced as measures of coal-cleaning performance. Their clear descriptions of the more important criteria that have been advanced and explanations of their meaning and application have been sorely needed and, if widely promulgated and followed, should remove much of the confusion which, heretofore, has been evident. I suggest that much of this confusion has also arisen from lack of common agreement as to the exact meaning of the words and terms used in our discussions of this subject. I am sure I have been equally guilty in this respect and suggest it is time that we select a committee to study vocabulary as well as criteria, so that common understanding and agreement can be had. Thus, I suggest, that the title of this paper should have used the words "coal-cleaning performance" and not "coal-washery performance." My understanding is that "washery" refers to a complete plant and it has additional functions to that of coal-cleaning, such as control of size, moisture, etc. Also, I do not agree with the authors that the formulas given in their paper, the Fraser and Yancey formulas, are necessarily the only ones that can be called efficiency formulas. When a dictionary is consulted one realizes that the words "efficiency" and "efficient" have not precise meanings but only very general ones and must be further defined for each particular use, if they are to have any precise meaning. To my mind, the first of the Fraser and Yancey formulas given should never be used as expressing "efficiency" alone but only by the fuller phrase which truly expresses the kind of efficiency it states, which is "coal recovery efficiency." For complete clarity we then need only define "coal" for the particular circumstances under which the formula is used. This would recognize the fact, fully explained by the authors, that the limits in coal qualities imposed by the market have imposed a factor—and a variable factor—which has influenced any answer obtained by this formula. Such a procedure makes it entirely practical and logical to use the values of any of the qualities of coal—ash, sulphur, phosphorus, specific gravity—or a combination of them to define what is coal for that particular use of the formula. Further, it is clear to me that the criteria to be used must be dictated by the objective in view and the use for which the data are obtained. The authors clearly point out that the Fraser and Yancey coal-recovery efficiency formula is influenced by three factors, "one is determined by the coal, one is dictated by market or use conditions, and one is an inherent characteristic of the cleaning unit itself." The formula which uses the inverse of misplaced material as a measure of efficiency is also a coal recovery efficiency formula and is influenced in like manner by these three factors. As the authors point out, both are useless in obtaining data which enables a direct and valid comparison of the performance of a given cleaning unit on two coals where the other two factors vary or of the performance of two or more cleaning units of different types unless the values of the other two factors are identical. Much of the confusion in our discussions of and literature on coal cleaning has come from failure to understand clearly this fact. Many such comparisons have been made from which erroneous conclusions have been drawn. I am, therefore, particularly glad to see the authors' emphasis on 4?-1e criteria which indicate the "sharpness of separation. I feel that these are the essential criteria

Jan 1, 1952