Search Documents

By R. L. Powell, E. C. Houston, V. J. Jones

The phosphate ores mined in middle Tennessee typically consist of granular rock phosphate particles disseminated in a clayey matrix. In the TVA plant near Columbia, Tenn., the phosphate ore is mined, made into a slurry with the addition of a small amount of sodium hydroxide as dispersant, and treated in a hydroseparator to remove minus 10 micron material. The hydro-separator underflow, comprising a rough concentrate, is transported by pipeline to the plant; the hydro-separator overflow, comprising a tailing, is flocculated by addition of calcium sulphate and is discharged to settling ponds at a rate of about 1400 gpm. Sedimentation in the ponds produces a clarified efluent, which may be recycled for use as process water or discharged to surface drainage. This method of tailing treatment is not entirely satisfactory since poor sedimentation characteristics of the tailing result in poor ultimate utilization of pond storage volume. The sediment contains about 70 pct water, even after several years of settling, and is not sufficiently dry to permit it to be used as back-fill, which would provide a method for reclaiming ponds that had been filled with sediment. Since important advantages would result from a process whereby the water content of the tailing solids would be made substantially lower than that obtained in the present process, several possibilities of achiev- ing this were considered. Flocculation tests were made with a wide variety of chemicals, but none gave any improvement over the results obtained with calcium sulphate. Filtering or centrifuging was found to be infeasible. Small-scale tests of dewatering by electrophoresis showed promising results, so this method was studied further in pilot-plant equipment. It was found that the tailing could be dewatered by electrophoresis to produce the solids in a form suitable for use as back-fill. However, the de-watered tailing has no monetary value at present, and the process is not economically competitive with settling pond operation under present conditions. This paper describes the pilot-plant work on electrical dewatering. It is believed that the data may find application in dewatering physically similar but economically valuable materials such as clays or mill slimes, or in dewatering phosphate tailing in the event of increased settling pond costs

Jan 1, 1950

By Stefan Boshkov, Malcolm T. Wane

THE validity and accuracy of velocity measurements underground have been questioned repeatedly by those in mine ventilation work. The general disagreement on the subject is well illustrated in an AIME publication.' Although the presence of errors is readily admitted, their magnitudes are not known and often are described by practical operators merely as "great," "small," or "of no importance." The belief that errors are of academic interest only prevails because of a justifiable claim that actual volumes of air circulated are well in excess of those required by law and safe mining practices. Poor understanding of the source and nature of errors inherent in velocity measurements, coupled with questionable determination of cross-sectional area, result in faulty techniques for the purpose of expediting ventilation surveys and render doubtful the calculated volume. Often consistency of readings is confused with accuracy. A succession of check readings showing a maximum deviation of 5 pct in the measured value of velocity usually signifies nothing more than diligent application of technique in a stable ventilating current. This article discusses the errors involved in air measurements underground. Where instrument errors are presented, the treatment is confined solely to the rotating-vane anemometer, recognized as a most useful ventilation measurement tool because of its simple design and easy operation. In the following pages a positive deviation is defined as one which has to be added to the registered air velocity to obtain the true air velocity.

Jan 1, 1956

By H. R. Hose

The total crude fluorspar reserves in Western Europe, including the USSR and the Soviet sphere, Thetotalare estimated to exceed 17 million metric tons. The total fluorspar production in 1951 in Western Europe, excluding the USSR and Soviet sphere, amounted to 371,109 metric tons. The chief fluorspar-producing countries in Europe, excluding Russia and the Soviet sphere, are France, Western Germany, Italy, Spain, and the United Kingdom. TOTAL crude fluorspar reserves in western Europe, containing more than 35 pct CaF2, are estimated at 12 million metric tons, while reserves in the USSR and Soviet sphere may exceed 5 million metric tons. The bulk of these reserves are concentrated in the USSR, Spain, United Kingdom, Western Germany, and Italy. Since published estimates of the tonnages of individual mines and explored deposits are not available for most countries in Europe, the estimates given in Table I for individual countries are necessarily approximate, as they have been compiled from various sources and modified and combined according to the author's judgment. The majority of fluorspar deposits in Europe belong to the late Paleozoic metallogenetic epochs and have been found within or along the borders of the Hercynian massifs. Deposits in the Central and Esterel massifs of France, those of Western and Eastern Germany, Sardinia, the Catalonian coastal range and the Sierra de los Santos in Spain, and those of Devonshire and Cornwall belong to the Hercynian metallogenetic epochs. The deposits in southern Norway and Sweden belong to the middle Paleozoic or later, those of northern England to the late Paleozoic or later, those of northern Spain and Greece to the late Mesozoic, and those of northern and probably central Italy and Switzerland to the early Tertiary. Fluorspar occurs typically in veins, lenses, and stringers, but also in bedded replacement deposits and pockets, and may be colorless to white, yellow, green, pink, brown, blue, or purple to almost black. Except for the colorless variety, the only kind which can be used for the optical industry, the color of the fluorspar does not affect its ultimate use. Crystalline cubic or octahedral fluorite of CaF2 composition, with 48.9 pct fluorine and 51.1 pct calcium, has a specific gravity of 3.18. The ore in place, however, usually averages 3.0 metric tons per cubic meter owing to the quantity of other minerals asso- ciated with the fluorspar in the veins and the physical state of the fluorspar, which may vary from sugary to massive crystalline or microscopic inter-growths with barite or quartz. Barite of 4.5 sp gr, quartz of 2.66 sp gr, and chert and calcite are commonly associated with fluorspar. Other minerals usually present in lesser amounts are celestite, wad, silver, lead, zinc, copper, iron, and uranium minerals. In some cavity fillings the rhythmic deposition of the fluorspar, barite, and quartz into successive crusts may make it possible to handpick the crude ore on belts or to separate the fluorspar from other minerals while the actual mining is carried on. Where metallurgical grade lump spar is required for foundries, separation of quartz and barite may be made also by jigs and heavy media, and in some mines the lead and zinc sulphides may be separated and recovered by vibrating tables. However, except in the case of unusually high grade deposits, acid grade fluorspar is obtained by flotation. By this process fluorspar deposits grading down to 35 pct CaF2 in the crude ore can be worked at a profit when fluorspar, lead, zinc, and silver prices are high, as the sulphides of these ores can be separated from the fluorspar by flotation and concentrated.

Jan 1, 1956

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By Reuben B. Ellestad, Fremont F. Clarke

Lithium chemical plant extraction methods are discussed with reference to 1) base exchange with alkali sulphates; 2) processing based on roasting with lime; 3) miscellaneous methods; and 4) application of the Lithium Corp. process to extraction of lithium from run-of-mine, low grade spodumene ore, or concentrates. IN the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2SO4) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K2SO4 is objectionable from cost considerations since purification of lithium carbonate requires the use of potassium carbonate, if the K2SO4 is to be recovered and recycled. The lower solubility of K2SO4 as compared with Na2S04 is also objectionable, since it limits the concentration of the Li2SO4 solution to be precipitated by K2SO4. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging. Other related base exchange processes are those of Lindblad, Wallden, and Sivander3 and Sivander, Gard, Villestad, and Wallen4. The former covers the reaction of lithium silicate minerals with a sodium sulphate solution, at 100" to 300°C (under pressure), while the latter involves the extraction of silicate minerals with molten sodium sulphate. Both these processes would seem to be difficult and expensive to operate.

Jan 1, 1956

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia and South Carolina to determine the technical feasibility of recovering commercial grade kyanite concentrates by flotation. The research indicated that combinations if sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. This report summarizes the results of these tests, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained kyanite. Extensive deposits of kyanite occur in the southeastern United States. The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate for many years at the present rate of consumption. According to Espenshade and Potter,' the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30% kyanite. The tonnage of kyanite-bearing gneiss and schist is much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina-South Carolina, and at Graves Mountain, Ga. Of the known deposits, only four were being mined for kyanite in 1 967. These deposits are near Farmville and Dillwyn, Va., Clover, S.C., and Washington, Ga.

Jan 1, 1970

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By Phillip E. La Moreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride. IN June 1940, the U. S. Geological Survey, in cooperation with the Geological Survey of Alabama, began a study of the ground-water resources of the part of Alabama where water is obtained from Cretaceous rocks. The purpose of the study was to determine the quality, quantity, occurrence, and availability of ground water in that area. These studies have been expanded to include ground-water investigations in the area of Tertiary rocks, or southern quarter of the State, and certain areas in northern Alabama. The first report issued on these studies was by C. W. Carlston,1 of the Alabama Geological Survey. In the present paper all references to ground-water data for the Cretaceous area are taken from this earlier publication. In 1945, the Dentistry Division of the Alabama Department of Public Health became interested in the correlation of tooth decay and mottled enamel with the chemical quality of ground water used for public supplies in the State. Through a cooperative arrangement between the State Department of Public Health and the Ground Water Division (now Branch) of the U. S. Geological Survey, a report by the author2 was published in 1948. These two reports give accurate information on the occurrence of fluoride in the Coastal Plain of Alabama. At present, only scattered information is available on fluoride in ground water of the crystalline-rock or Piedmont area and for the Paleozoic area of Alabama, but it is hoped that in the future more complete information on the presence of fluoride in ground water in these areas can be collected. Outline of Geology and Ground Water: As described by Adams,3 the State of Alabama includes parts of two major geologic divisions, the Appalachian region and the Coastal Plain. The boundary between these divisions is irregular and is known as the Fall Line of the Atlantic and Gulf Coast States. The Fall Line enters Alabama near Phoenix City, extends westward to Wetumpka, Clanton, and Tuscaloosa, and then swings northwestward to the northwest corner of the State. The Appalachian region in Alabama includes three major provinces, the Piedmont province, the Appalachian Ridge and Valley province, and the Appalachian Plateau province (fig. 1). The rock formations in the Piedmont province in east-central Alabama are mainly of pre-Cambrian age, chiefly crystalline schists and gneisses injected by younger igneous rocks (fig. 1, I). They are faulted and folded and have a complicated structure. These rocks are the oldest and among the most complex rocks in the State. Generally, only small yields of ground water are obtained from rocks in this area. Even though ground water is of great importance for the development of domestic and farm supplies in rural areas and a few small industrial and municipal wells, yields in the area from individual wells generally range from 5 to 25 gpm and rarely exceed 50 gpm. The geologic formations of the Appalachian Ridge and Valley province and the Appalachian Plateau province (see fig. 1, II, and III) are separated on the basis of their structure. These rocks are of Paleozoic age, ranging from Cambrian to Carboniferous, and comprise a succession of formations consisting chiefly of shale, sandstone, limestone, and dolomite, aggregating many thousands of feet in

Jan 1, 1951

By Phillip E. La Moreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride. IN June 1940, the U. S. Geological Survey, in cooperation with the Geological Survey of Alabama, began a study of the ground-water resources of the part of Alabama where water is obtained from Cretaceous rocks. The purpose of the study was to determine the quality, quantity, occurrence, and availability of ground water in that area. These studies have been expanded to include ground-water investigations in the area of Tertiary rocks, or southern quarter of the State, and certain areas in northern Alabama. The first report issued on these studies was by C. W. Carlston,1 of the Alabama Geological Survey. In the present paper all references to ground-water data for the Cretaceous area are taken from this earlier publication. In 1945, the Dentistry Division of the Alabama Department of Public Health became interested in the correlation of tooth decay and mottled enamel with the chemical quality of ground water used for public supplies in the State. Through a cooperative arrangement between the State Department of Public Health and the Ground Water Division (now Branch) of the U. S. Geological Survey, a report by the author2 was published in 1948. These two reports give accurate information on the occurrence of fluoride in the Coastal Plain of Alabama. At present, only scattered information is available on fluoride in ground water of the crystalline-rock or Piedmont area and for the Paleozoic area of Alabama, but it is hoped that in the future more complete information on the presence of fluoride in ground water in these areas can be collected. Outline of Geology and Ground Water: As described by Adams,3 the State of Alabama includes parts of two major geologic divisions, the Appalachian region and the Coastal Plain. The boundary between these divisions is irregular and is known as the Fall Line of the Atlantic and Gulf Coast States. The Fall Line enters Alabama near Phoenix City, extends westward to Wetumpka, Clanton, and Tuscaloosa, and then swings northwestward to the northwest corner of the State. The Appalachian region in Alabama includes three major provinces, the Piedmont province, the Appalachian Ridge and Valley province, and the Appalachian Plateau province (fig. 1). The rock formations in the Piedmont province in east-central Alabama are mainly of pre-Cambrian age, chiefly crystalline schists and gneisses injected by younger igneous rocks (fig. 1, I). They are faulted and folded and have a complicated structure. These rocks are the oldest and among the most complex rocks in the State. Generally, only small yields of ground water are obtained from rocks in this area. Even though ground water is of great importance for the development of domestic and farm supplies in rural areas and a few small industrial and municipal wells, yields in the area from individual wells generally range from 5 to 25 gpm and rarely exceed 50 gpm. The geologic formations of the Appalachian Ridge and Valley province and the Appalachian Plateau province (see fig. 1, II, and III) are separated on the basis of their structure. These rocks are of Paleozoic age, ranging from Cambrian to Carboniferous, and comprise a succession of formations consisting chiefly of shale, sandstone, limestone, and dolomite, aggregating many thousands of feet in

Jan 1, 1951

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pig-ments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 A as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut. In light of the above, a project was initiated for the formation of single crystals of rutile. Method of Formation of Rutile Single Crystals Fortunately, purification of TiO2 produced from both titanium tetra-chloride and titanyl sulphate solutions had reached the stage where spectro-graphically pure starting material could be made. Spectrographic analysis of the feed material used in the initial experiments is compared with the present feed material in Table 1. It is apparent that the present large scale purification is approximately as good as the original experimental, small scale purification. Verneuil1 produced synthetic ruby and corundum in 1904 by the well-known flame fusion process, which today bears his name. Except for mechanical improvements the present commercial production of synthetics by flame fusion is essentially unchanged from his initial method. His burner consisted of an inner orifice through which was fed the feed material and oxygen. Surrounding this was a larger outer orifice through which was fed hydrogen at lower pressure. This arrangement consists then of a lance of oxygen burning in an atmosphere of hydrogen. The proportions of hydrogen to oxygen usually used in corundum production is about 3:1, providing there is sufficient temperature to reach the 2050.°C required for the fusion of alumina. From work done in the Titanium Division Laboratories2 and from the published work of Erlich3 it was known that rutile appears to lose oxygen near its melting point and that it would not be possible to grow single crystals in a strongly reducing environment. Consequently, in order to determine whether single crystals could be grown at all, an Airco oxygen-acetylene torch with

Jan 1, 1950

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By R. C. Amero

FULLERS earth is a general name applied to claylike minerals that have high natural ad-sorptive powers. They are usually distinguished from ordinary clays by a higher content of combined moisture and a lower apparent density. The definition is based on the ancient use of the material for fulling, or cleansing woolen cloth of oil and grease; a more modern definition should mention the ability to decolorize oil and should differentiate between fullers earth, which is naturally active, and certain bentonites which only develop decolorizing power after being leached with strong mineral acids. The distinction between fullers earth and activable bentonite is not a sharp one, since all types of intermediate clays can be found that are more or less naturally active, yet more or less responsive to acid treatment. The differences seem to depend somewhat on the amount of leaching that has been effected by natural ground waters. Physical Properties The principal mineral constituent of activable bentonite is montmorillonite, a hydrous aluminum silicate to which the following formula is generally assigned: Al,Si,O,, (OH), • 12H,O Fullers earth, as well as bentonite, is usually composed of some variety of montmorillonite, but in the United States the largest tonnage of fullers earth is mined from deposits of attapulgite. Attapul- gite is a clay mineral composed of monoclinic crystals of colloidal size, having a fibrous shape similar to that of asbestos. A sectional model of the attapulgite "molecule" is shown in Fig. 1. A single unit is about 18.0 A wide and 12.9 A high. The length of the molecule is variable, but this same molecular pattern is repeated to form needlework crystals, rather than flakes, as is characteristic of the montmorillonite crystals. Attapulgite has been assigned the following formula,' although actually, the magnesia has been largely replaced by alumina: (0%) . (OH), • Mg, . Si, • Olp . 4H20. The fibrous nature of the mineral is clearly shown in the electron micrograph, Fig. 2. Although the deposits contain 5 to 30 pct quartz and carbonate minerals, impurities in the commercial products are held at a low level, principally by selective mining on the basis of oil decolorizing efficiency. The particle size distribution of this fullers earth has been estimated from settling rates, using sodium citrate as a dispersing agent.' Since Stokes' law only applies to spherical particles, the equivalent particle diameter calculated below is probably more nearly an index of diameter rather than length of the needlelike crystals: Eqnivalent Arbitrary Particle Distribution, Size Diameter Pci Classil3catian 0.05 mm 0.80 0.80 pct sand 0.05-0.02 mm 10.96 0.02-0.01 mm 9.65 42.10 pct silt 0.01-0.005 mm 11.40 0.005-0.002 mm 10.09 2-0.5 micron 10.61 0.5-0.2 micron 29.09 56.58 pct clay 0.2-0.05 micron 14.86 0.05 micron 1.96 The differential thermal analysis shown in Fig. 3 is unique and supports the theory that this is a distinct mineral species.' ~ Other general properties of the mineral as shown in Table I.

Jan 1, 1952

By L. Moyd, P. Moyd

The first commercially available portable gamma ray-neutron beryllium detector, the Rerylometer, was developed by the same group that developed the first practical portable scintillation counter, the Scintillo-meter. This group includes Professor George Brownell, of the Geology Department of the University of Manitoba in winnipeg, and his associates, K. I. Roulston, R. w. Pringle, and R. L. Funt, of the Physics and Engineering Departments of the University of Manitoba. A prototype model was tested in the field by Dr. Brownell during the summer of 1958. Commercial production was undertaken shortly thereafter by Nuclear Enterprises Ltd., of Winnipeg, and a license for manufacture and distribution in the U.S. was granted to Isotopes Specialties Co., of Burbank, California, a division of Nuclear Corporation of America. Early in 1959, we were retained by the 'Mining Division of Minerva Oil Co. to Legin a search throughout North America for minable deposits of beryllium, and to train members of their permanent staff to continue the program. The project included literature sur-veys, interviews with members of various federal, state, and provincial agencies, scanning of our own collection of suites of specimens from various mineral occurrences, and the examination of deposits in the field. The value of a beryllium detector to this program was obvious and arrangements were made to procure one as soon as possible, which resulted in our obtaining and using the first instrument that was produced commercially in the U. S. In addition to the commercially available Berylometer, Mr. William Vaughan and his associates, of the U. S. Geological Survey Geophysics Division, in Denver, have developed and tested several experimental instruments based on the same principles. DETECTOR Principles The detection of beryllium is based on the fact that "hard" gamma rays (1.6 MEV and geater), such as those produced by Antimony convert ordinary beryllium (Be9) to Be8 , with the release of a neutron. The neutrons are counted by a scintillator designed to favor neutron responses while suppressing those of gamma rays. 'The instrument is completely selective for beryllium. No other element can interfere. Instrunlentation The Rerylometer itself, which is cylindrical, is about 8 inches in diameter, 13 inches high, and weighs about 11 pounds. (Figs. 1, 2). The principal components include: 1. A disc of wax to moderate (or "thermalize") neutrons. 2. A boron-enriched polyester-zinc-sulphide fluorescent screen. This material produces strong flashes when struck by thermalized neutrons but only weak flashes from gamma rays. 3. A photomultiplier tube. 4. An electronic circuit, complete with one srnall 71/2-volt dry battery. The photomultiplier tube and electronic circuit convert neutron flashes to electrical impulses, but gamma ray effects are almost

Jan 1, 1961

By V. E. McKelvey

The Phosphoria formation of the northwestern states presents a stimulating challenge to workers in every field of mineral technology. In addition to its large reserves of phosphate, the formation has been found to contain important amounts of fluorine and several metals, such as vanadium, nickel, and molybdenum. Because these minor metals in the Phosphoria do not have their usual glitter, concentrations of them are not easily discovered nor appraised. Like the phosphate itself, production of these metals very likely can be achieved only through use of costly chemical methods, for their mineralogy precludes treatment by the usual methods. In addition, in much of the area the containing rocks lie in complexly folded and faulted structures, which complicate mining and increase its cost. Yet the chain of research necessary to establish what elements are present; their geographic and stratigraphic distribution and reserves; the most suitable methods for recovering them; the combination of beds which, when ruined and processed, will yield the greatest recovery of the most valuable elements; and the methods most adaptable to their profitable extraction may well lead to the development of an important mineral industry and may make possible a significaut reduction in the cost of fertilizer this in itself would be an achievement of momentous importance—and at the same time make the nation more self-sustaining in critical materials. Although this research has great

Jan 1, 1950

By D. A. Keyes

International Minerals & Chemical Corp. (Canada) Ltd. is presently exploiting by underground mining a potash-rich zone in the middle Devonian Prairie Evaporite formation near Esterhazy, Saskatchewan. Of the three main potash-bearing horizons denoted by Goudie as zones 1, 2 and 3 only the 1ower. two are present at Esterhazy and mining is confined to the lower or zone 1 horizon. The area in which the evaporites were deposited, although flanked on the west by a zone of geosynclinal deposition and tectonic activity, has been subjected to only very gentle epeirogenic activity. The sylvinite ore is coarsely crystalline and occurs in well-defined beds. The halite, sylvite and insoluble content of the ore bears a direct relationship to the lithological units, but the carnallite cuts across the beds. Local concentrations of salt produce blank spots in the ore horizon. Some of these appear to be salt-filled, post-ore channels and cracks while others have been formed by brines emanating upward from below the ore. INTRODUCTION International Minerals & Chemical Corporation (Canada) Ltd. is operating an underground potash mine near the town of Esterhazy in eastern Saskatchewan. The deposit was discovered by IMC in 1955. Subsequent drilling outlined extensive high-grade reserves, and in 1957 shaft sinking and plant construction began. Production from Yarbo No. 1 Shaft commenced in September, 1962 and quickly reached the initial capacity of one million tons of muriate product per year. Production is currently being expanded to 1.6 million tpy. The single mining level is 3140 ft below the surface at No. 1 Shaft. GENERAL GEOLOGY The Esterhazy district lies within the Interior Plains region of Canada and on the northeast rim of the Williston Basin (Fig. 1). Average dip of the rock formations in this area is about 40 ft per mile to the southwest. The potash ore occurs in the Prairie Evaporite formation of the Middle-Devonian Elk Point Group. The Prairie Evaporites are overlain by 3000 ft of Paleozoic shales and limestones and by Jurassic and Cretaceous sandstones and shales (Fig. 2).

Jan 1, 1967

By Richard H. Jahns

GRANITIC pegmatite deposits are the chief source of commercial feldspar, sheet mica, beryllium, tantalum-columbium, and lithium minerals, and certain types of kaolin. They also have yielded significant quantities of cassiterite, gems, scrap mica, molybdenite, tungsten minerals, uranium-thorium and rare-earth minerals, and zircon, either directly or as the sources of placer deposits. The output from pegmatite mines in the United States is small as compared to other mineral products in terms of bulk or value, and much of it comprises minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. Never was United States dependence upon pegmatite mining more clearly emphasized than during World War 11, when greatly expanded demands and uncertainties of foreign sources of supply caused much concern. Such commodities as beryl, tantalite, and sheet muscovite remained high on the critical list for months at a time, and for some minerals there was a real struggle to achieve and maintain a favorable ratio of supply to demand. Satisfactory stock piles of certain sizes and qualities of sheet mica, for example, were not built up until late in 1944, when wartime requirements already had begun to level off or even to decrease. Production of all the strategic pegmatite minerals from domestic deposits during World War I1 constituted only 10 pct or less of the total domestic consumption of these minerals, but the importance of this contribution should not be minimized. Domestic production often represented the difference between increase and further reduction of existing stocks of commodities already in seriously short supply, and in the early stages of the war it was the only assured source if imports were cut off. During the recent war period, the U. S. Geological Survey carried on a program of pegmatite studies in the New England and Southeastern States, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California as shown in Fig. 1. Several papers and reports already have appeared as an outgrowth of this work,'-= and others are in preparation. This paper outlines some results of data obtained by the writer during the period 1942 to 1946, when he was engaged in studies of pegmatites in the Southeastern, Southwestern, and Rocky Mountain States. Beryllium Minerals Beryl is the present commercial source of beryllium metal and beryllium compounds, which are used in ceramics, in the preparation of X-ray tubes and fluorescent lamps and screens, in special processes of paint and textile manufacture, and in the optical systems of some electrical instruments. The metal also is used in nuclear physics, chiefly as a source of neutrons. Beryllium is alloyed with aluminum for certain light-metal uses and is a constituent of some nickel and iron alloys. Currently the chief demand, however, is for copper-base alloys, which are exceptionally resistant to fatigue and wear, are responsive to hardening treatments after

Jan 1, 1952

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951