Search Documents

By N. L. Carwile, G. W. Geil

A metallographic study was made of deformation twinning (Neumann lamellae) in ingot iron slowly deformed in tension at —196O and —150°C. The results showed that twinning is initiated mainly during the initial stages of plastic deformation. However, the breadth of the twins generally increases with increase in strain up to fracture of the specimen. HE results of an investigation of the effect of low I temperatures on the flow, fracture, strain hardening, and strain aging characteristics, and the true stress-strain relationship for specimens of ingot iron deformed in tension were reported recently.1,2 In that study specimens of ingot iron, in different initial conditions, were slowly deformed in tension at various temperatures between —196" and +100°C. A phenomenon observed, but only briefly reported, was the formation of deformation twins (Neumann lamellae) in the specimens deformed at the lower temperatures. Preliminary metallographic examination of these specimens indicated that there was apparently some correlation between the deformation twinning and the strain of the specimen and that this factor merited further investigation. Some recent investigations have indicated a direct association of Neumann lamellae and the fracture of the metal. Bruckner".' * postulated that the twinning immediately precedes the fracture and the latter is initiated by the stopping of the propagation of twins, either at subgrain boundaries or at other structural features. Tipper and Sullivan5 postulated that Neumann lamellae are initiated by the shock or a shock wave set up at fracture in the still highly stressed unbroken metal, and that a high rate of deformation is a necessary condition for their formation. An extensive metallographic examination, therefore, was made of many of the specimens used in the study of ingot iron at this Bureau and of additional specimens deformed to selected strains under various conditions. The present paper summarizes the effects of deformation under these conditions upon the breadth and scope of the deformation twins. Other features of twinning will be discussed in another paper. Material and Testing Procedure All of the specimens were prepared from one lot of ingot iron, as hot-rolled, of chemical composition other than iron as follows: C, 0.02 pct; Mn, 0.02; P, 0.005; S, 0.018; Si, 0.002; Cu, 0.10; 0, 0.058; and N, 0.002. Cylindrical tensile specimens with a 2 in. gage length were used. The reduced section was slightly tapered from each end; the diameter (0.438 in.) at the midsection of the gage length was about 0.003 in. less than at the ends. The specimens were finished to the final dimensions by grinding and polishing in the axial direction. The ends of the specimens were machined with 3/4 in. x 10 threads and the shoulder fillets were machined to a radius of 0.75 in. The specimens were extended slowly in tension (deformation rate less than 0.5 pct reduction in area per minute) while immersed in an appropriate cryogenic liquid maintained at the desired temperature. The minimum diameter of the specimen was measured during the test by means of a specially designed reduction of area gage accurate to 0.0001 in." A detailed description of the testing equipment and the method of maintaining the desired temperature is given in a previous paper.' Each specimen, after deformation to a specified strain at a selected temperature, was sectioned longitudinally and examined metallographically. The preparation of specimens for metallographic examination was carried out in the usual manner by mechanical polishing and etching. Results and Discussion Deformation twins in specimens of ingot iron extended slowly in tension at —196" and —150°C are shown by the representative micrographs of Figs. 1

Jan 1, 1954

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1' studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium' and to the tensile ductility of a-B titanium alloys.' These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.' The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957

By Alfonso Merlini

DIFFERENT explanations have been given by the two current theories of the annealing textures for the variation of annealing texture with the annealing temperature observed in rolled polycrystal-line aluminum,' copper,2 and brass, And in rolled single crystals of copperk and silicon iron.' The theory

Jan 1, 1957

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By I. R. Kramer

The apparent activation energy, U, JOY plastic deformation of aluminium, copper, and gold single crystals and polycrystalline aluminum was found to he dependent upon surface condition. At low strains, the value for U for aluminum single crystals was 4200 cal per mole ; however, this value decreased to 920 cal per mole when the specimens were polished during the test at a rate of 50 X 10-5 win-1 The activated volume also was found to increase with the rate of metal removal. That the surface plays an important role in plastic-deformation processes has been adequately demonstrated.1-4 Of particular interest at this time are the observations4 that the creep rate of single crystals of fee metals is increased markedly when specimens are polished during the deformation process. These observations were interpreted in terms of a dislocation debris layer at the surface regions of the crystal. This layer, which appears to be a region containing a high concentration of dislocations or segments of dislocations, not only will impede the egress of dislocations on the primary slip system, but will also provide a barrier against which dislocations may pile up. By this means, a stress which opposes the motion of dislocations will be generated. It is considered that this stress must be taken into account in any theory which describes the plastic-deformation process. Although a detailed dislocation model cannot be given at this time, it may be stated that the stresses opposing the motion of dislocations arise from the dislocations in the debris layer, Ts, and ti due to the resistance to motion imposed by internal obstacles such as Lomer-Cottrell barriers, subgrain and grain boundaries, forest dislocations, and so forth, as well as the resistance due to the presence of jogs on dislocations and the interaction of the stress fields of dislocations, and so forth. In essence, we have added an additional term, ts, to the usual form of the equation T = Ta- Tb, where Tb is the back stress due to the various types of obstacles which impede the motion of dislocation. Accordingly, the net stress, t, acting on a dislocation may be written as where Ta is the applied shear stress. For deformation which occurs by a thermally activated process5,8 ?=Ae-u/kT = A e(u,-VT)/kT [2] and U = Uo- Vt PI where U = activation energy for plastic flow, y = shear strain rate, Uo = activated energy for plastic deformation in the absence of stress and depends upon the particular deformation process, V = activated volume, k = Boltzmann constant, T = temperature, OK, and A = frequency factor. From Eqs. [I] and [3], U = Uo- V(Ta - Ti - TS) [4] and it is seen that if Ts decreases, the activation energy, U, must decrease if V remains constant. However, as will be shown, V is a function of the surface conditions. In their work on aluminum, Lytton and coworkers7 reported that at low strains the activation energy was 3400 cal per mole and at high strains it was 28,000 cal per mole. The lower value was interpreted in terms of the energy necessary to overcome the Peierls force, while the higher value was associated with the energy necessary for dislocations to move by a cross-slip process. It will be shown that the lower activation energy is associated with the surface debris layer rather than with the Peierls force. EXPERIMENTAL PROCEDURE Single crystals having a nominal cross section of 1/8 in. and a 3-in. gage length were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The initial purity of the metals was 99.997, 99.999, and 99.999 pet for aluminum, copper, and gold, respectively. The orientation of the specimens is given in Fig. 1. The measurement of the activation energy as a

Jan 1, 1964

By Samuel Storchheim

IT was noted that variations existed in the magnetic properties, namely, coercive force, He, and rema-nence, Br, of 18/8 stainless steel wires of the same analysis when these wires were given the same percentage of reductiori of area at different rates of reduction. In order to determine the extent of these variations, a program was initiated whereby commercial 302 and 304 stainless steels were drawn with a wide variation of speeds. Ultimate tensile strengths and specific resistances, as well as the Hc-BT measurements, were determined. If variations of considerable magnitude were found, it was thought that the knowledge accrued from the investigation could probably aid in determining the particular drawing speed required to obtain desired properties for a given specification for a particular analysis of wire. Drawing Procedure Two specimens (set I, No. 302 and No. 304), the chemical analyses of which are given in Table I, were drawn at different speeds, namely, 45 to 3900 ft per min, directly from 0.016 in. diam wire to 0.004 in. diam wire, a 93.7 pct reduction of area. To obtain this high percentage of reduction, the wire at 0.016 in. was softened by annealing at 1150°C. It was then strung in a No. 16CF variable speed Vaughn drawing unit and passed through 13 B.&S. gage dies of successively smaller diameter, as shown in the accompanying table. Following this step, several hundred feet of the wire was drawn, at a particular speed, through the dies and wound upon a spool. Once the sample of wire was drawn at the desired speed, the spool with the finished sample was removed, tagged for later identification, and an empty spool was placed in the machine. Another wire sample was drawn at a different speed, after making the necessary adjustments upon the Vaughn unit. At the greater speeds, several thousand feet of sample were drawn to insure that the wire to be used for testing would be uniform. This was done because the desired speed was not reached instantly; the wire taking a short while to attain the required drawing rate. All speed measurements were made by placing a tachometer against one of the machine's pulleys during the actual drawing of the specimens. 84.4 pct reduction of area. The 0.072 in. diameter wire was also annealed at 1150°C. The process of obtaining samples was the same as described above. The only difference between the two was that the rates involved were not as extensive, set II covering a range of 625 to 1150 ft per min. Tensile tests were carried out for the 0.004 in. diam wires on a horizontal Scott Tensile Tester, while tensile tests for the 0.028 in. diam wires were made on a vertical Scott Tensile Tester. Each value listed in the tables represented the average of five samples with a maximum deviation of approximately 3 pct among the samples. Resistance per foot of the wires was determined by use of standard bridges accurate to the nearest hundreth of an ohm for the 0.004 in. wire, and to the nearest thousandth of an ohm for the 0.028 in. wire. The resistances per foot were then converted to resistivities by use of the following equation: P = RxCM where R is the resistance per ft in ohms per ft; CM, the area in circular mils; and P, the resistivity in ohms—CM. The values listed in the tables likewise

Jan 1, 1952

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,' Dahl and Pawlek,' and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

By J. W. Borough

THE electrical conductivity of pure copper is markedly decreased by small amounts of impurity in solution. The magnitude of this effect has been very carefully determined by numerous investigators who studied a wide variety of impurity elements. Much of this work is summarized in an excellent review by Pawlek and Reichel.' The case of zinc impurity in copper is an exception to the above in that there has been no well-documented study of the effect using high-purity starting materials. The values for the effect of zinc on conductivity, which are usually taken from unpublished work by Skowronki, indicate that zinc in low concentration has no effect whatever in lowering the conductivity of pure copper. This effect, if true, is unusual since it is generally known that even in lowest concentration, impurities exert an effect on conductivity which is proportional to the amount dissolved. It is more reasonable to suspect that in the original work on the effect of zinc some of the zinc was oxidized out of solution during specimen preparation. The following experi- and calculated d-spacings based on the unit cell dimensions of Baenziger et al. Since the single crystal studies of Baenziger et al. were limited to (hk0) and (hk 1) data, it was not possible to Compare all the intensities of the powder and single crystal patterns. However, the strongest reflections of both studies, the (321) reflection, agree very well when the appropriate multiplicity factor is used. Good agreement was also found in a number of other reflections of lesser intensity. Despite the precautions taken in annealing the U6Fe powder, an appreciable amount of UO, was detected in the powder pattern after heat treatment. The powder pattern reported by Groganoand Clews is given in Table I. Except for the 3.15A line, which is the strongest line of UO,, their pattern, as far as it goes, compares favoEably with the data from this study. Gordon and Kaufmann have reported a diffraction powder pattern purported to be U, Fe but it bears very little resemblance to the patterns of Table I. ments were carried out to redetermine the effect of zinc on conductivity using high-purity starting materials and processing conditions capable of producing oxygen-free alloys. Materials used in the experiment were ASR 99.999 pct Cu and Cumingo 99.999 pct Zn. Four 1 lb melts were prepared with identical procedure in argon atmosphere with crucibles made from Speer No. 580 graphite. The compositions were 0.0, 0.1, 0.3 and 1.0 pct Zn. Standard No. 14 wire (0.064 in. diam) was made from these melts as follows. The 1 pct Zn sample was first reduced 94 pct by cold swaging with five annealing treatments of 800o for 10 min in hydrogen between swagings, and then reduced 94 pct to the

Jan 1, 1962

By T. E. Leontis

Data are presented in this paper to show that addition of zirconium to sand-cast Mg-Th alloys effects a marked decrease in the grain size of these alloys which is accompanied by a significant increase in the mechanical properties over the entire range of thorium content investigated. The beneficial effect of zirconium on the strength properties is maintained at elevated temperatures up to 700°F. In addition the alloys exhibit exceptionally high creep resistance at temperatures up to 600°F. Zirconium does not greatly improve the strength or creep characteristics of extruded Mg-'Th alloys. Cerium is not a desirable addition to Mg-Th-Zr alloys. IN a previous paper,' it was shown that addition of thorium to magnesium imparts exceptionally high resistance to creep at elevated temperatures both in the sand-cast and in the extruded states. The large grain size of the sand-cast alloys, however, renders them of questionable value as engineering materials. Sauerwald² showed that the grain size can be reduced effectively by the addition of zirconium. Results of a detailed study of the properties of Mg-Th-Zr alloys over a wide range of thorium content are presented in this paper. In accordance with the preliminary findings of Sauerwald,² it is shown here that Mg-Th-Zr alloys possess the unusual combination of fine grain size and a high level of strength and creep resistance at elevated temperatures. Some information on the effect of cerium on the properties of Mg-Th-Zr alloys is presented also. Effect of Th on Solubility of Zr in Molten Mg Sand-cast test bars and 3 in. diam extrusion billets of Mg-Th-Zr and Mg-Th-Ce-Zr alloys* were pre- pared according to the procedures described in the previous paper.' The zirconium was added in the form of sponge metal as supplied by the Bureau of Mines.' The maximum amount of zirconium that usually can be introduced into magnesium at the customary alloying temperature of 1350° F is about 0.7 pct. The analyses in Table I clearly show that thorium in- creases the solubility of zirconium in liquid magnesium. The tabulated zirconium contents are designated as "acid soluble;" this serves to distinguish these values from the small amount of zirconium that is not dissolved when the alloy is subjected to the action of a dilute acid solution. The "acid-insoluble" zirconium is believed to be ineffective as an alloying ingredient. The acid-insoluble zirconium contents ranged between 0.03 and 0.16 pct in the present alloys, the tendency was toward higher values in alloys with higher thorium content. In contrast to the effect of thorium, cerium decreases the solubility of zirconium in magnesium. This is shown by the three Mg-Th-Ce-Zr alloyst in- cluded in Table I and stands in agreement with the observations of Nelson and Stricter".' on Mg-misch-metal-Zr alloys. Effect of Zr on Grain Size of Mg-Th Alloys The potent effect of zirconium as a grain refiner has been demonstrated for many types of magnesium alloys.3-8 Of greatest importance to date are Mg-Zn-Zr alloys5,6,8 and Mg-mischmetal-Zr alloys.3,4,7 Zirconium has also been found to exert a marked grain-refining action on Mg-Th alloys. All the Mg-Th-Zr alloys cast in the form of ½ in. diam test bars have an exceedingly fine grain size (Table I). Reference to the previous paper' will show that binary Mg-Th alloys containing up to 6 pct Th are almost completely columnar even in the M in. diam reduced section of a test bar, and that 10 to 50 pct Th alloys have an equiaxed grain structure of 0.03 to 0.08 in. The data in Table I also show that addition of cerium to Mg-Th-Zr alloys has no effect on the grain size. In addition to increasing the strength properties, the fine grain size of Mg-Th-Zr alloys

Jan 1, 1953

By H. H. Smith, G. J. Danek, M. R. Achter

Nickel, Type 316 stainless steel, and copper show decreases in reversed bending fatigue strength with increases in air and oxygen pressure. The leveling off of the log N us log p curve for nickel at 300" and 816°C is discussed in terms of a model in which surface saturation gives rise to a critical pressure. A metallographic study indicated that the effect of environment on crack initiation and growth rates is a function of temperature. It is shown that small amounts of impurities in inert gases may substantially reduce the fatigue strength of nickel. 1n a previous investigation1 of high-temperature bending fatigue in air and in vacuum, reversals in the effect of environment with changes in test conditions were atrributed to a mechanism consisting of two processes acting in competition. One of them, oxidation strengthening, has been demonstrated in a straightforward manner by measuring the rupture strength of a sintered nickel-oxide bond.' The detailed operation of the other process, facilitation of crack propagation by surface absorption of oxygen, is uncertain. Thompson et UZ advanced the possibility that the formation of an oxide layer prevented rewelding of cracks during the compressive part of the cycle, while Wads worth and Hutchings4 further proposed that the reaction of oxygen with atoms at the tip of the crack helped the metal to break there, a possibility which has also been advanced to explain crack formation in creep.5 A difficulty in arriving at a mechanism for this lowering of fatigue strength in air is the inconsistency of some of the data. For example, Wadsworth and Hutchings4 found an approximately linear decrease of log cycles-to-fracture (N) with an increase of log pressure-of-air (p) for copper and aluminum at room temperature, while snowden,' although finding a similar linear dependence for aluminum, observed a stepped curve for lead. Between l0-' and 10"1 torr there is a sharp decrease in the fatigue life of lead with increasing air pressure, but plateaus, signifying no dependence on pressure, are found at higher and lower pressures. If, as discussed elsewhere: these environmental effects arise from the adsorption of gas on crack surfaces, it would be expected that as the pressure is increased a saturation point would be observed, beyond which there is no further effect. To gain further information about the form of the log N vs logp curve, it was decided in the present investigation to repeat this type of measurement at elevated temperature on nickel, copper, and Type 316 stainless steel. An additional object of this program was

Jan 1, 1963

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn's temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By John W. Weeton, Donald W. Petrasek

Relatively few metal-metal systems exist that would permit the creation of fiber-metal composites consisting of mutually insoluble constituents. It is anticipated that most high strength-to-weight ratio and high -temperature fiber composites ultimately to be produced will utilize high-strength fibers embedded in a highly alloyed matrix. An investigation was conducted to determine the effect of alloying on the tensile Properties and micro-structure of tungsten-fibey-reinforced composites. Composites were made of tungsten fibers infiltrated with copper binary alloys that contain elements of varying solubility in tungsten. Room-temperature tensile tests were made on the composites, and a metallographic study of the microstructure of the fiber-metal-matrix interfaces was conducted. It was shown that, as the depth of penetration of some alloying elements into the fiber increased, a decrease in both tensile strength and ductility of the composite results. A notch effect, due to the formation of a brittle alloy zone with the tungsten fiber, was observed and gave rise to greater reductions in tensile properties and ductility behavior than would be Predicted by a law-of-mixture relation alone. In recent years, investigators have considered combining fibrous materials with relatively weak binder materials. The interest in fiber-reinforced composites results from the fact that fibers or wires may be exceedingly strong and exhibit mechanical properties superior to those of the bulk materials from which they are derived. For example, tungsten wires drawn to less than 1 mil in diameter may have strengths of over 600,000 psi,' while steel wires ranging from 10 to 3 mils in diameter may have strengths of the order of 300,000 to over 600,000 psi.2 Both metallic and ceramic whiskers are known to have very high strengths. For example, iron whiskers have been shown to have strengths of 1.9 million psi3 and sapphire whiskers have been reported to have strengths of the order of 1.7 million psi.4 If all or part of the strengths of such fibers could be retained, subsequent to the incorporation of the fibers in an engineering material, a superior material could result. In previous work done at the Lewis Research Center, McDanels, Jech, and weeton5 demonstrated the feasibility of fabricating metal-fiber—metal-matrix composites that utilized the full strengths of the fiber and matrix materials. Tungsten fibers were combined with a copper matrix by a liquid-infiltration method such that the tungsten fibers were uniaxially oriented parallel to the tensile axis of the composite. A linear relation was established that related the tensile strength of the composite with the volume percent of the fibers. Mutually insoluble constituents were selected for the study so that the strength of the composite could be quantitatively related to the strength of the individual constituents. The fact that there are only a few metals that are mutually insoluble with tungsten, e.g., copper, silver, gold, and zinc, and that these either have low melting points, high vapor pressures, or poor oxidation resistance, makes it necessary to utilize other metals that are soluble in tungsten, where high-temperature applications are ultimately contemplated. It was anticipated that, for most practical fiber-reinforced composite materials, it would be necessary to use a fiber and metallic matrix that would have varying degrees of solubility for each other. A logical extension of the earlier work was thus felt to be a study that would determine the effects of elements that had mutual solubility with the tungsten. Numerous investigators have found that tungsten fibers may be damaged by thermal treatments or contamination of the surface of the fiber by alloying elements.6-10 On the other hand, surface treatments may improve the strength of such fibers."-" Relatively little work with composites containing tungsten fibers have been reported. The work of parikh14 has shown that kinked, short-length tungsten, steel, and molybdenum fibers could str'engthen such matrices as silver, gold, and copper. Some of the combinations of fibers and matrices studied by

Jan 1, 1964

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The effects of ternary and quaternary additions of aluminum, oxygen, and carbon on the mechanical properties of high-purity titanium-molybdenum alloys were studied for several microstructural conditions. Heat treatments were designed to produce 1) ß-quenched, 2) equiaxed ß) transformed (acicular) and 4) stabilized -P microstructures. Tension, impact, and hardness tests were performed. Transformations from the ß phase were followed by hardness measurements and metallography. The ß-to-w transformation was slowed by aluminum additions; carbon and oxygen additions increased the transformation rate. In addition to solid-solution strengthening, these solutes may increase or decrease strength by altering the /3 transformation kinetics. Aluminum additions promote the formation of strain-induced martensite, and lower yield strengths at compositions near 12 pct molybdenum.. a-P alloys are more ductile with equiaxed than with transformed microstructures. High strength levels can be reached by aging in many cases. Strength levels of the aged specimens usually are lowered slightly by straining prior to aging. ALLOYS of molybdenum with titanium form an iso-morphous alloy system which has been the subject of several investigations. Additions of substitu-tional and interstitial -stabilizing elements provide means of improving mechanical strength and con- trolling the heat-treatment response of the binary alloys. The work reported here forms a part of a continued study of the effects of microstructure on the mechanical properties of high-purity titanium alloys. Previous papers have considered the various binary alloys (Ti-Mo, Ti-Al, Ti-C, and Ti-0) that form the bases for the ternary and quaternary alloys included here. The compositions were selected to correspond with the previous binary alloys. Further, the high purity of the alloying components was maintained, so that direct comparisons with earlier work can be made. The total research program included a large number of compositional, microstructural, and testing variables. The data reported here have been selected to provide a reasonably complete and representative summary of the results. The reader is referred to the original Air Force Report for a complete tabulation of the results. EXPERIMENTAL PROCEDURES All the alloys used in this work were prepared from high-purity electrolytic titanium produced by the U.S. Bureau of Mines. A typical furnished analysis showed the following impurities in wt pct, balance This analysis is equivalent to that of iodide-refined titanium. In addition, hardness, tensile, and impact tests made using unalloyed electrolytic titanium showed it to have properties equivalent to those obtained with iodide titanium and suitable for these studies of high-purity base alloys.

Jan 1, 1962

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures'-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.' The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant' determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle' and ~ayward.' According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958