Search Documents

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By C. B. Thwing

IT is likely that among most races, owing to the ease of finding and working clay, the making of clay utensils was learned earlier than the molding of metal implements. The ancients made good pottery and durable brick in kilns that wasted fully one-half the heat and spoiled fully one-fourth of the ware; and, taking the clayworking industry as a whole, we are doing the same today. The chemical and physical changes involved in the burning of clay are so many and vary so much with the composition of the clay that it is not surprising that the rule-of-thumb methods so commonly employed fail to give uniform results. In its passage from plastic clay to the vitreous or stonelike character the mingled minerals and accidental organic impurities of which the clay is blended must pass through four stages, the second and third usually overlapping, and the fourth often beginning before the third is complete. These stages in their order with the rising temperature are drying, dehydration, oxidation, vitrification. In the first part of the drying stage, usually accomplished in part outside the kiln, the water mixed with clay is dried out at temperatures not much exceeding the boiling point of water. In the later part of this stage, within the kiln, the hygroscopic water, absorbed from the air is expelled at somewhat higher temperatures, this stage being known as watersmoking. Some clays are very sensitive to temperature during the drying stage and if the temperature exceeds 100°, the ware becomes checked. Other clays may be dried more rapidly without danger. In down-draft kilns, the draft is slight during the watersmoking stage and the water driven off from the top rows condenses on the ware in the bottom of the kiln, with the result that high temperatures are likely to be reached at the top of the kiln before the bottom is fully dry. The lag in temperature of the bottom persists to the second stage in spite of the better draft then prevailing.

Jan 9, 1919

By Kirtland Marsh

THE manufacture of gas masks by the Chemical Warfare Service, U. S. A., required preparation of the carbon used in the canisters. The largest plant for the production of this carbon was situated at the works of the Astoria Light, Heat and Power Co., at Astoria, N. Y.; this paper will deal1 with the pyrometry equipment at that plant. Commercial charcoal was found unsuitable for use in gas masks because of its low power of absorption and its poor resistance to abrasion. The best raw material for the production of carbon was found to be coconut shells, but any kind of nut shells or fruit pits were used when sufficient quantities of coconut shells could not be obtained. The shells were first carbonized in retorts, the carbon was then crushed and screened between 8 and 16 mesh, and finally submitted to a special heat-treatment in air; steam treatment was later substituted for treatment in air. The production of gas-mask carbon on a commercial scale was begun at Astoria about Aug. 1, 1917. Temperature control was essential during the initial carbonization of the shells, as well as during the air or steam treatment, and pyrometers were installed for this purpose. The installation and maintenance of all pyrometry equipment was done by the pyrometry department, consisting of an officer in charge, an assistant, and two men. A special pyrometry laboratory was maintained in which all repairs were made.

Jan 9, 1919

R. W. NEWCOMB, New York, N. Y. (written discussion *).-This paper is particularly interesting to me, because it gives data on a much mooted question, viz., the serviceability of Le Chatelier (platinum-platinum-rhodium) thermocouples under severe industrial conditions. It has always been supposed that platinum-platinum-rhodium thermo-couples, used at high temperatures under strong reducing conditions, would not give long service and were subject to rapid volatilization. The fact, however, that the carefully kept records indicate that a little more than 3 gm. out of more than 830 gm. was lost over this considerable period, shows what kind of service can -be obtained from platinum-platinum-rhodium thermocouples,, when properly installed, and well cared for. While the writer has no actual figures on the loss of weight, etc. of platinum-platinum-rhodium thermocouples under service, he was told, by the man in charge of pyrometers at a large industrial plant in which over 400 platinum-platinum-rhodium thermocouples were installed in furnaces doing various kinds of heat-treating work, that the average maintenance cost, for materials alone, including platinum-platinum-rhodium wires and protecting tubes, was 27 c. per furnace, per month:

Jan 12, 1919

By Gifford White

CONSIDERABLE attention has been directed in recent years to methods of electric prospecting other than the conventional direct-current tech-niques. It has been extensively recognized that electrical data of a more general nature than that possible by direct-current methods might be useful in geophysical studies. To this end, a number of different types of electric currents have been employed, such as single-frequency alter-nating currents, square-topped periodic current waves,4 periodic surges of a less specific nature,8 and suddenly applied direct current.1,2 Yet, to the author's knowledge, little analysis of these different types of driving currents has been made from the standpoint of network theory to determine just what type of currents would give the most useful data, and, most important of all, to determine the relation of the data taken by one method to those of another. Without touching on the actual theoretical problem of how currents flow in the earth under specified boundary conditions, some very useful information can be obtained from the study of the fundamental integral equations of electrical networks, throwing light on the problem not ordinarily appreciated by the field worker. Some manipulation of the standard network equations will be made, with the sole purpose in mind of developing expressions leading to practical results. Suppose that four points in the earth have been located and it is wished to obtain the most useful type of electrical data by inserting current into two of them and measuring the potential developed between the other two. The first problem that arises is that of which pair of the four shall be chosen as current grounds. In the direct-current case, where only steady potentials are measured, the selection is of little consequence, but as soon as currents varying with time are used at the current grounds, a new effect arises. The fact that a varying current is flowing in the current-carrying conductor between the current grounds means that magnetic and electric fields varying with time will be produced

Jan 1, 1940

By S. W. Hurlbut

12.4 Application of Research Findings. After the findings of research have been evaluated and approved, there remains the problem of translating them into practical usage. It frequently happens that this is the more difficult phase of the research project. Hitherto, the problems have been largely associated with material objects and scientific laws. When the findings of research are implemented in the field, the human factor becomes the most important element bearing on success or failure. From this point on, the attitudes and reactions of people of all kinds are involved, and just how they are involved and their relation to successful implementation is the subject of the remainder of this section. 12.41. Management Attitudes. To engage in research at all implies management backing to a degree. But this could be dictated by overall company policy or by just some executives in the hierarchy of management. The existence of research per se does not necessarily mean that there is a solid, unanimous echelon of management executives who sincerely believe in the fruits of research, who have an earnest desire to make breakthroughs, and who have a willingness to take calculated risks. Under the ideal condition of complete management backing, translating the results of research into practice is greatly facilitated. If management accepts the results of research as valid, the order is given, or it has been established by precedent that those results will be implemented. The rest of the organization will have grown to accept the fact that this is so, and that the results must be given a fair trial in the field. However, this ideal condition probably exists but rarely, and it is against a background of incomplete, or partial, management backing that most results of research must be implemented. At the present time, the climate for research in the mining field is less than perfect but is improving rapidly as the realization grows within the industry that the way toward taking its proper place in the Space Age is by applying to mining the philosophy and techniques of research that made the Space Age possible.

Jan 1, 1968

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By T. M. Chance

THE necessity of adopting improved methods of bituminous-coal cleaning at. many collieries is recognized by all familiar with the requirements of the various bituminous markets, the approaching exhaustion of the relatively small areas of inherently high-grade-coal, and the difficulties encountered in maintaining a uniform grade of shipped coal. Many coals lose much of their .market value by degradation in size, and, in any event, if the cleaning process is to contemplate wetting the coal the minimum amount of fines should be produced to prevent sludge losses and the difficulties resulting from the moisture content of the wet fines. Hence, it is desirable to by-pass the finer coal dry, if this can be done without too-great increase in impurities in the final product. This procedure has given excellent results at washeries at Steelton and in the Birmingham district. If the raw fines are too impure to permit admixture with the washed coal, it may be desirable to use dry methods, such as the pneumatic table, rather than to wet an excessive amount of such fine material. The bituminous-coal cleaning plant should therefore: (1) Treat the raw coal in as large lump as possible and without sizing; (2) eliminate degradation of pure coal -in the washing process; (3) avoid wetting the fines, if possible; (4) produce washed coal practically free from mechanically included impurities; (5) crush the refuse and retreat, if much intergrown coal, and refuse are present, rather than precrush the entire feed. Ordinary gravimetric methods of concentration, whether hydraulic or pneumatic, will not meet all of these requirements, as the large lump includes those sizes. now sent to the picking tables, if it is desired to treat material of such size. I do not know of any prior commercial method, based on the falling velocity, coefficient of friction or resistance to fracture, that permits the production of clean coal varying in size from, say, 10-in. lump to 1/16 -in. mesh.

Jan 6, 1924

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By Glenn C. Waterman

The use of stream sediment and soil sampling as an aid in exploration has markedly increased in recent years as more and more attention has been directed to areas that are generally geologically favorable for mineralization but show little outcrop. Numerous ore deposits and many hundreds of mineral deposits that have no surface exposure have been found associated with anomalous geochemical patterns. Sophisticated techniques have been developed to "wring out" of geochemical data subtle information that is pertinent in defining areas of exploration interest. Variations in metal patterns in soils and sediments as they are affected by pH, Eh, weather, topography, etc., are pretty well known. Field studies have determined the variations and controls of metal ion distribution in the several soil horizons and the contributions to metal concentrations made by different types of vegetation. Less well known is how to interpret geochemical data since thickness of soils over bedrock varies in an unknown fashion and, particularly, where glacial debris of unknown thickness is piled on top of soils or scoured bedrock.

Jan 7, 1975

By W. H. W. Husband

Rock salt has been solution mined for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the same method. However, only Kalium Chemicals Ltd. has been successful, possibly because the conditions in Saskatchewan are the most favorable to be found so far for the development of a solution-mining method for potash. In view of the fact that few studies of solution mining of potash have been attempted, only one company has succeeded in using the method, and no information has been released by this company, the application of solution mining of potash ore bodies has to be presented on the basis of available theory, past small-scale studies, and recent patents. A simple mining method is outlined and possible methods of recovering the potash from the brine are discussed. Dissolution data pertaining to solution mining of potash, flowsheets, and material balances are presented. The available information is brought together in a cost analysis to show capital and product costs in terms of 1966 dollars.

Jan 1, 1972

By William M. Sheehan

TRANSPORTATION is one of the most important problems of the mine operator and the possibilities of cost reduction in this field should not be overlooked. In the railroad industry, cars and locomotives have been improved greatly, and the progress there made is well worthy of study by the mine operator looking for maximum efficiency in every branch of his activities. One of the outstanding developments in the construction of railroad equipment in recent years has been the wide-spread adoption of large one-piece steel castings for the framework of locomotives, passenger and freight cars. Some of the advantages and applications of this type of construction will be outlined in this paper, with particular thought of the needs of the mining industry. The inherent qualities of cast steel: homogeneity, unrestricted size and shape, high tensile strength, flexibility of metal distribution, resistance to corrosion, and gracefulness of outline, make it the most versatile member of the ferrous group. Not only is it a strength-giving element, but it is corrosion resistant, a combination that makes for large economies in equipment maintenance. Flexibility of metal distribution allows the integral foundation to be in the shape best suited for the purpose. These cast structures are really assembled in the mold in liquid form and the metal can be placed in the right pro¬portion exactly where it is needed, thus securing weight economy and uniformity of fibre stress. Such a process permits the incorporation, with ease, of necessary brackets, utilizing them to provide not only greater strength for the derail part itself, but often to add to the value of the entire unit. Laps, seams, and joints, which are necessary in all fabricated forms, are eliminated.

Jan 1, 1933

By Thomas Cox

THIS paper makes no claim to any new idea; it simply reviews the Treasury Department Regulations pertaining to the practical application of depreciation and depletion and other allowances governing taxation of oil and gas properties. Other methods may be existent, but as they may not conform to the legal status they must be discarded. In complying with the present laws governing the, industry with regard to taxation and the allowable deductions therefrom, the following considerations are essential: Depletion, depreciation, amortization, other allowances, and items not deductible. It is definitely understood that depletion is the loss or exhaustion sustained in the continuous operating of an oil and gas property, and that each unit of oil or gas taken out reduces the value of the property until its final exhaustion. Depletion applies only to the natural deposits of oil and gas due to their-removal in the course of exploitation of any property. Depreciation is defined to cover the waste of assets due to exhaustion, wear and tear, and obsolescence of the physical property, and is separate and distinct from depletion; its allowance is that amount which should be set aside for the taxable year in such sums as for the useful life of ,the property will suffice to repay its original cost-or its value as of Mar: 1, 1913, if acquired by the taxpayer before that date-less the salvage value at the end of such useful life. Amortization is allowed for such facilities as were built or acquired on or after Apr. 6, 1917, for the production of articles contributing to the prosecution of the war and, in the case of vessels, those built and acquired after that date. The amount to be extinguished, in general, is the excess of the unextinguished or unrecovered cost of the property over its maximum value under stable .post-war conditions.

Jan 9, 1920

By C. H. Bowen

Industry needs a generally applicable means of defining average grain sire and grain size distribution. Students of sediments have explored this field, employing methods that might also prove useful in engineering problems. Before attempting to solve specific problems it is well to review the derivation of commonly used grade scales and the reasons for their selection. This aspect of the problem seems largely to have been lost, and a review of basic factors may suggest causes for failures in using size analysis data.

Apr 1, 1956

By Edgar Shepard

THE interest of the Federal Government in improvement of water-ways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duty of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investi-gations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as "308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects.

Jan 1, 1940

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By Kevin M. O’Connor

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation in rock masses induced by mining. The first example involved monitoring the propogation of overburden fractures above a longwall coal panel and the second example involved the use of TDR to monitor rock mass deformation in the vicinity of a strip mine highwall. Rock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By James C. Fisher

Traditional uranium exploration techniques were utilized and comparatively evaluated in the Front Range, Colorado uranium province. Intense surficial leaching and thick colluvial cover render traditional airborne and ground radioactivity reconnaissance prospecting useless. Radon gas emanometry and sulfur gas emanometry were slightly more effective but the long and short term variations In soil gas emanation rates make it extremely difficult to gain useful information from these systems. The technique judged most useful was Track Etch radon prospecting. The excellent definition of the technique, as well as its repeatability, indicate that it is an ideal prospecting tool for narrow vein-type deposits similar to those of the Front Range, Colorado.

Jan 1, 1976

By M. Baeyertz

SINCE 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer1, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallography. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types.

Jan 1, 1930