Search Documents

By E. A. Lucero, H. E. Robbins, T. H. Dudley

EL Salvador mine of Andes Copper Mining Co., E subsidiary of Anaconda Co., is in northern Chile about 18 miles north of Potrerillos, 7825 ft above sea level. Initial production is planned for the first half of 1959. Plant capacity will be 30,000 tpd, and there are 308,835,000 tons of proven ore reserves, averaging 1.49 pct Cu. The Inca adit is being driven as part of the mine-to-mill haulageway. Because of the overburden it is planned to mine the deposit by block caving. Ore will be dropped from upper gathering levels through ore passes to the Inca adit, through which it will be transported out of the mine to the primary crushing plant located a half mile from the portal.

Jan 3, 1958

By Alberto J. Terrones L.

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,1 by Barrel1 on Marysville, Mont.,2 and by Goldschmitt on the Oslo district, Norway,3 laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf4 made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control5 ore finding. Some years later Harrison Schmitt6 fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed.

Jan 3, 1958

By R. Lee-Aston

HALLOWAY mine of Tennessee Copper Co. at Copperhill, Tenn., has been under development for several years. It has two shafts, the A shaft, 1336 ft deep from the surface to the 16 level, and the B shaft, lying 500 ft to the southeast and extending 1385 ft deep from the 10 level down to the 24 level. A section through the two shafts, Fig. 1, shows the development work entailed by the proposal and the area involved. The Problem: For operational reasons it was necessary to extend the B shaft from the 10 level to surface, and the pilot hole and raising method was chosen. This method had been used to extend the Company's Boyd manshaft from the 10 to the 14 level in 1954, but no satisfactory hole surveying method had been employed. In that instance, when the hole was located it was found to be about 8 ft from its calculated position. The success of this shaft extension method lies in the ability to keep the pilot hole within the proposed shaft diameter for nearly the entire length. The approximate 670 ft of extension distance in one hole was thought to be excessive because of deflection encountered locally in other core drilling. Since a connection between the two shafts, intermediate between the surface and the 10 level, would be required at some future date, the pilot hole drilling was done in two sections. This intermediate level was fixed at the 6 level and distances became 470 ft from surface to the 6 level and 230 ft from the 6 to the 10 level. A rock pentice of 25 ft was left temporarily in place just above the 10 level.

Jan 3, 1958

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand there has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of -200 mesh material in the final product markedly increases costs of dewatering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins.

Jan 2, 1958

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and re- quires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged be- cause a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced.

Jan 2, 1958

By James H. Courtright, Kenyon Richard

TOQUEPALA is a porphyry copper deposit in which mineralization is localized by a large breccia pipe formed in dose genetic relation to intrusive rocks. The deposit is in southern Peru, 55 airline miles north of the small city of Tacna and the same distance inland from the port of 110. Quellaveco and Cuajone, geologically similar deposits, lie 12 and 19 miles north of Toquepala. Chuquicamata is 400 miles to the south. The deposit is high on the southwestern slope about 20 miles from the crest of the Cordillera Occidental of the Andes Chain. It lies in a mountainous desert where the steep southwesterly slope of the Andes is dissected by a succession of rapidly downcutting, deep canyons. Local topography is moderately rugged with a dendritic drainage pattern and an elevation of 8000 to 14,000 ft. Volcanic peaks along the crest of the Cordillera rise over 19,000 ft.

Jan 2, 1958

By Harry E. Krumlauf

The year 1957 was one of declining metal price and production. Many lead-zinc-copper mines were forced to close, and the remaining mines limited production to stay more in line with demand. High cost of labor, supplies, and equipment and high taxes aggravated the situation. Some operators postponed or abandoned expansion programs because of uncertain economic conditions. Output was curtailed by elimination of over- time employment and reduction of the working force. The number of employes laid off was small- reduction in the labor force was accomplished by not replacing those who left a company's employ.

Jan 2, 1958

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications-those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicating and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement CO. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible.

Jan 2, 1958

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division OFFICERS AND COMMITTEES S D Michaelson, President J W Woomer, President-elect Elmer A Jones, Past President C E Lawall, Eastern Regional Vice-President G Donald Emigh, Central Regional Vice-President J D Forrester, Western Regional Vice-president R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1958

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

By W. Chubb

FOR the past several years there has been considerable interest in the development of zirconium and zirconium alloys for application in nuclear reactors. In a portion of the development work being conducted, attention has been given to the development of high-strength zirconium alloys. One of the most outstanding alloys developed in the course of this work is Zr-4 wt pct Sn-1.6 wt pct Mo.' Fabrication and Test Methods Over 50 ingots of zirconium containing either tin and molybdenum or both have been evaluated in the process of selection of an optimum composition. Most of these were prepared as 20-g are-melted buttons; a few were prepared by induction melting. All ingots were prepared by the me of Foote Mineral

Jan 1, 1958

By Arthur Lubinski, K. A. Blenkarn

It is explained why the bottom portion of freely suspended tubing in a pumping well buckles and straightens in succession during the pumping cycle. Field evidence of resulting rod-on-tubing wear, excessive polished rod load, and excessive horsepower are given. The possibility that buckling hastens pump wear is strongly suggested. Means for either prevention of buckling or for mini-mizing its effects are explained, their relative merits compared, and field results of their use given. These means are: tension anchors, tail pipe, sucker rod guides, and corrosion inhibitors. Charts and formulas for best use of tension anchors, tail pipe, and guides are given. Use of tension anchors, or compression anchors with a heavy tail pipe, prevents both buckling and breathing, thus improving volumetric efficiency. Without tail pipe, buckling above compression anchors precludes such improvement. INTRODUCTION It is well known that a column must be subjected to some compression in order to buckle; and also that a structural member does not buckle if subjected to a tension. When consideration is given to a tubular column, the question may be asked, "How is the buckling phenomenon affected by inside or outside pressure?' At first, it seemingly should not be affected. However, this is not so. In order to arrive at a correct deduction one should first understand the basic reasons for buckling of a column under loading*. Then he should add to the effect of that loading the effect of pressure. Following this procedure, one may discover quite unexpected phenomena. In some cases, when subjected to more pressure inside than outside, a pipe may buckle under tension. In other cases, a pipe may remain straight, although subjected to a very large compression. In 1950 and 1951 it was explained why the bottom portion of a string of pipe freely suspended in a well does not buckle even when subjected to a large compression due to buoy- ancy.2,3 It was shown that the com-monly used concept of a neutral point, as being a point in the string with neither compression nor tension, is inadequate, and a more relevant definition of the neutral point was introduced. The findings were also generalized to cases of different pressures inside and outside a pipe.3a Later, in a further generalization, allowance was made for variations of stress and pressure with depth.' The findings were applied to the new technique of hydrostatic high pressure testing of lengths of pipe in the mill.5 In 1952 it was observed that previous theoretical findings apply to tubing in pumping wells. The lower part of freely suspended tubing buckles during the upstroke portion of the pumping cycle. Later, it was ascertained that this phenomenon is responsible for wear and malfunctioning of the equipment. Various remedial measures were devised and successful field trials conducted. Only brief mentions on the subject have been published.6,7 In this paper, the phenomenon of tubing buckling is explained, field

Jan 1, 1958

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By H. I. Aaronson

ONLY limited studies have been made of pro-eutectoid a morphology in hypoeutectoid Ti-Cr alloys during previous investigations, 1-3 The nature of the eutectoid reaction, ß?a + TiCr2, has been considered in somewhat more detail.1,2,4,4 Inasmuch as the proeutectoid ferrite reaction in plain carbon steels has recently been extensively investigated in this laboratory, advantage has been taken of the opportunity to compare the morphologies developed in two rather different eutectoid systems in order to permit a preliminary estimate to be made of the degree of generality which may be ascribed to the various results obtained. Experimental Procedure The chemical analyses of the alloys used are given in Table I. The 7.22 pct Cr alloy was prepared by the Battelle Memorial Institute from iodide titanium and high purity chromium. The initial ingot was made by arc melting a master alloy and iodide titanium. The resultant ingot was twice remelted. by the consumable electrode technique. Upset forging at 950°C reduced the final ingot to 3/4 in. sq bars. The 10.94 pct Cr alloy was prepared by the Titanium Metals Corp. of America from sponge titanium and chromium of ordinary purity. This alloy was melted twice by the consumable electrode technique, forged at 1200° to a 3/4 in. sq bar, and rolled at 815°C to a 1/2 in. round. Specimens 1/4 in. x 1/4 in. x 1/16 in. were cut from the 7.22 pct Cr alloy; halves of disks 1/2 in. in dlam and 1/16 in. thick served as specimens of the 10.94 pct Cr alloy. These specimens were individually encapsulated in Vycor, Each capsule was evacuated three times to a pressure of 2 to 6 x lo-' mm Hg and flushed twice with a reduced pressure of argon prior to sealing. The inclusion of two small packets of zirconium chips permitted the capsules to be outgassed and internally gettered, without heating the specimen, prior to heat treatment. The specimens were solution annealed for 40 min at 1000°C, isothermally reacted in deoxidized lead pots, and quenched in iced water. Most of the isothermal reaction treatments were carried out at 25" intervals between 725° and 550°C on specimens of the 7.22 pct Cr alloy and at 650°C on specimens of the 10.94 pct Cr alloy. Results and Discussion Morphologies of Proeutectoid a*—Kinetics of the ß?a Reaction: Fig. 1 shows the TTT-curves for the beginning of the proeutectoid a and the eutectoid reactions in the temperature range investigated in the 7.22 pct Cr alloy. The M, temperature in this alloy is below 0°C. The curve for the beginning of the proeutectoid a reaction is in good agreement with that of Frost, Parris, Hirsch, Doig, and Schwartz' for a 7.54 pct Cr alloy, appears at considerably earlier reaction times than the corresponding curve presented by Rostoker4 for a 7 pct Cr alloy, and lies athwart the curve of Spachner and co-workers11 for an 8 pct Cr alloy. Differences in criteria for the beginning of the a reaction and the relatively high rate of this reaction at lower temperatures presumably account for some of these divergences and may also explain, in part, the apparent failure of an iodide-base 7.22 pct Cr alloy to react more slowly than sponge-base 7 to 8 pct Cr alloys. Grain Boundary Allotriomorphs: Crystals of this morphology nucleate at and grow preferentially and more or less smoothly along the matrix grain boundaries.5-7 Allotriomorphs are the first morphology to precipitate at most grain boundaries at reaction temperatures from 725°C, the highest temperature studied, at least through 575°C. Fig. 2 Shows typical allotriomorphs, formed during an early stage of transformation at 725°C. Grain boundary allotriomorphs are not the predc=iaant morphology at late reaction times at any temperature studied. However; from 725" through

Jan 1, 1958

Jan 1, 1958

By G. C. Wallick

Since the appearance of the paper, "Solution of the Equations of Un-steady State Two-Phase Flow in Oil Reservoirs," by W. J. West, W. W. Garvin, and J. W. Sheldon,' a two-fold investigation of this subject has been carried out. One objective of the investigation has been to deter-mine the feasibility of solving such problems 7on a medium-size com-puter such as the Datatron*, and the other objective has been to in-vestigate the application of such cal-culations to experimental and theo-retical petroleum reservoir research. In the first Datatron calculations, the fluid and rock properties published by West, et al, were used, together with the published equations describ-ing the system. Details of the formu-lation not given in the original paper are discussed in the Appendix to this note. Reference should be made to the subject paper for the complete equations and defintion of symbols. An unexpected result of this in-vestigation was the discovery that the linear solution published by West was in error. Thus, in addition to describing the Datatron solutions and to discussing certain numerical diffi-culties which will be encountered if one uses the published method of solution, the purpose of this note is to indicate the nature of this error. LINEAR FLOW Since the linear case requires a minimum amount of scaling, a fixed-decimal point Datatron program was written for the one-dimensional flow problem and an attempt was made to duplicate the solution described by West. In the case described, fluid was produced at a constant rate, Q, until such time as well pressure reached 0.04. Production was then continued at constant pressure. From the constants and curves given by West it was determined that the ini-tial constant production rate could be approximated by Q = 0.007. An ini-tial dimensionless time step ?t = 0.434 X 10 - "as used, and each suc-cessive time step was doubled until a value of = 0.444 was reached. This constant interval was then used for the remainder of the solution. In subsequent solutions, several varia-tions in the time schedule were em-ployed, including smaller time steps and slower rates of increase in the time steps. In all cases, almost identical results were obtained regardless of the time schedule employed. However, as described below, it was noted that the time schedule had some influence on the rate of convergence of the solutions. As a check on the accuracy of the solution, the cumulative production at each time step was calculated using the two methods described in the Appendix. Satisfactory agreement was observed with the differences in these two values of the order of two parts in 50,000. It should be noted that the mass balance check as described is of questionable value, particularly with regard to the well pressure and saturation. This is especially true in the radial solution where pressure and saturation values near the wellbore would make only a negligible contribution to the numer-ical integration. It is believed, how-ever, that such a comparison is ot value in determining the over-all accuracy of a solution. In comparing the Datatron solu-tion with that published by West it was discovered that in the later stages of depletion, the pressures near the well declined more rapidly in our solution than in the West solution, and that the limiting well pressure of 0.04 was reached at an earlier time than that originally reported. It thus became evident that it would be impossible to duplicate the production schedule described by West and a constant rate of production was maintained until the well pressure was equal to 0.0. A representative comparison of the results published by West with those obtained in this investigation is shown in Fig. 1, which is a plot of GOR as a function of cumulative recovery. These two curves should be in agreement until a cumulative recovery is reached which corresponds to a well pressure of 0.04 — for the Datatron solution, a recovery of approximately 5.6 per cent. Actually, a major disagreement is evident. Subsequent correspondence

Jan 1, 1958

By Marling J. Ankeny

MINING research in the U. S. today is indeed complex, whether it involves the Government, a small private concern, or a large one. And it promises to become more so, despite great advances already made in developing equipment and technology. The U. S. Bureau of Mines is committed to place greater emphasis on mining research as expressed in a recent policy statement to Congress on the "Long Range Minerals Program," by Secretary Fred A. Seaton, quoted above.

Jan 1, 1958

By R. Casting, J. Philibert, and C. Crussard

APPARATUS described in this paper uses the properties of X-radiation, emitted by substances under electron bombardment, as a means of rapid chemical point analysis. The method is based upon the principles of emission X-ray spectrography pioneered by Moseley in 1913. A very finely focused beam of electrons—the electron probe—is projected on the surface of a sample, which has a very large area compared with the beam diameter, at the point where it is desired to know the chemical composition. The minute volume of the sample which is thus irradiated emits a complex X-ray spectrum consisting principally of the characteristic radiations of the elements present in the volume. Measurement of the wavelength and intensity of each component of this spectrum thus affords a simple method of determining the chemical identity and concentration of these elements. The volume of sample which is analyzed at each position of the beam is limited by the diffusion of electrons in the sample. For an accelerating potential of the electron beam of about 30 kv, which is a convenient value for producing the characteristic radiation, this diffusion extends over a diameter of about 1 µ normal to the beam, and about 2 µ in the direction of the beam. Thus a beam of 1 µ in diameter leads to a volume of about 2 µ in diameter being irradiated. The limits of the analyzed region are thus considerably smaller than those obtained by using spark or arc emission spectrometry, which must extend to about 50 µ at right angles to the beam, and those obtained in X-ray fluorescence analysis, where the penetration of the specimen is considerably greater. The apparatus itself consists of three main parts: an electron optical system. an X-ray spectrograph and an optical microscope. The electron opticai system consists of a tungsten cathode emitting the electrow and a pair of magnetic lenses which focus the electron beam on the specimen to be analyzed. The specimen is prepared in the usual way, as in optical micrography. The X-radiation, emitted at the focal spot where the electrons strike the sample, is analyzed with a curved crystal, Geiger-Müller counter, vacuum spectrograph. The light microscope, designed to observe the surface of the sample in the region to be analyzed, is provided with a reflecting objective placed on the axis of the second magnetic lens. Its magnification is X450. The quantitative determination of an element A in the analyzed region is made by measuring the intensity I, of a strong characteristic line of the element, as emitted from the sample, and then the intensity I (A) of this same line as emitted from a

Jan 1, 1958

By John B. Campbell, George G. Binder, Loren H. Jenks

Conventional methods of producing crude oil generally leave in the depleted reservoir 1 to 3 bbl of oil for every barrel brought to the surface. This paper describes a field test which explores the possibility of using gas-driven liquid propane to improve oil recovery efficiency. Laboratory theoretical and experimental studies leading to the field test indicated that low residual oil values could be obtained using limited amounts of propane driven by gas. The field test involved (I) repressuring the reservoir to the vapor pressure of liquid propane, (2) injecting the liquid propane, and (3) injecting dry natural gas to drive the propane and oil to the producing wells. Considerable preliminary work, including new drilling, work-overs, and a pressure survey was necessary. During the test, oil production rates have averaged about nine times the final primary rates. The field average GOR is still below the pre-test value. Oil recovery to date is 112,000 STB. About one-third of the 143,-000 bbl of propane injected has been produced to date. Results of the C-2 block test are encouraging and larger, more definitive field projects ore indicated. INTRODUCTION The cost of finding new crude oil reservoirs continues to increase. Today the oil industry is drilling more and deeper wells and making fewer big discoveries. Nevertheless, the demand for oil and oil products increases each year. It is natural that oil companies, faced with this situation, concentrate on recovering more of the oil existing in our known crude oil reservoirs. There is room for much improvement. For every barrel of oil brought to the surface by present day methods of producing crude oil, generally 1 to 3 bbl are left behind in the depleted reservoirs. The "unrecoverable" oil in petroleum reservoirs is largely "trapped" by capillarity. Since flushing with a solvent is exceedingly effective in combatting oil loss due to capillarity, much effort in this direction has been made in recent years1,2,3,4,5. Liquefied petroleum gas (LPG) has been suggested as a relatively inexpensive. abundant, easily recoverable solvent for crude. Some operators have observed striking responses in oil recovery at production wells offsetting input wells in LPG storage reservoirs6,7,8. In spite of the low unit cost of LPG, however, it is uneconomic in general to inject a volume of LPG into a reservoir to remove a like volume of oil. A modification of solvent flushing in which a limited quantity of liquid propane is gas driven through a reservoir appears capable of recovering much more than 1 bbl of oil per barrel of propane injected. Also, most of the propane injected should be recoverable for sale or re-use. Since such a process could well have widespread and profitable application, The Carter Oil Co. is making an extensive evaluation of the technique's possibilities. Laboratory development of the gas-driven propane recovery technique was sufficiently encouraging to justify testing in the field. Since 1952, the Production and Research Departments of The Carter Oil Co. have cooperated in a field test in the C-2 Block leases of the

Jan 1, 1958

By W. H. Holman, J. B. Wagstaff

IN spite of considerable interest among blast furnace operators on the question of the penetration of air into the furnace, there is still uncertainty as to how far the blast does, in fact, penetrate. Moreover, it is not always clear just what is meant by the word penetration in this sense. In 1952, Elliott et al.1 showed that at the end of each tuyere of a blast furnace there is more or less of a void. In this region, coke particles are blown around by the force of the air. This explained the well-known observation reported by Sweetser2 hat if a bar is pushed into a furnace through a tuyere it will go easily into the furnace a distance of some

Jan 1, 1958