Search Documents

By L. D. Wooddy, W D. Moore

Water drives may be natural or artificial. For the case of a natural water-drive reservoir, the volume of water influx corresponding to reservoir pressuve-production history may be calculated by means of the material bal-ance-unsteady state equation. For the artificial water drive or pattern injection water flood, the material balance equation is sufficient to determine the reservoir pressure-production, injection history. However, for both cases to reliably predict reservoir performance, it is necessary to calculate the saturation distribution of the reservoir fluids at different stages of depletion. This paper consolidates the various equations used to determine the performance of water-drive reservoirs into one approach that is applicable to any reservoir that has a natural water drive or is to be produced by water injection. The numerical procedure has been simplified considerably, and the solution is adaptable to either hand calculations or digital computer operation. INTRODUCTION A water-drive reservoir is one in which the predominant source of energy for production of oil results from the encroachment of water into the oil zone. The water drive may be either natural or artificial. Water invasion takes place by expansion of water in the aquifer as a result of the pressure decline transmitted from the oil reservoir. Because water is practically incompressible, a natural water drive requires an extensive aquifer containing a volume of water many times the volume of oil in the reservoir. Provided the permeability of the formation is reasonably high, a moderate decline of reservoir pressure usually causes adequate water influx. If the reservoir pressure decline becomes excessive because of low permeability or a high rate of production, part of the oil production may result from the liberation of dissolved gas which may cause excessive quantities of free gas to be produced along with the oil. In extreme cases, reservoir pressure may decline so rapidly as to cause the oil to be produced predominantly by dissolved gas drive, leading to abandonment of the reservoir before the advancing water has had a chance to flush the entire reservoir. In reservoirs that are not connected to extensive aquifers, an artificial water drive may be created by injecting water into or around the lower edges of a reservoir. Sometimes water is injected within the reservoir through wells interspersed among the producing wells. When injection is carried out in such fashion, the reservoir is in effect subdivided into a number of separate producing segments, in each of which the displacement of oil is simultaneously taking place, and the shapes of which are fixed by the well patterns employed. Because of the natural tendency of oil and water to segregate according to their relative densities, water will tend to migrate downdip regardless of where injected. Accordingly, the injected fluids can be retained within the intended reservoir segments only when conditions are unfavorable to their migration under the force of gravity. Pattern injections are usually confined, therefore, to reservoirs having low structural relief, or low permeability, or when production and injection rates are such that fluid movements in the reservoir are dominated by the pressure gradients rather than by the force of gravity. In the case of natural water-drive reservoirs and artificial water-drive reservoirs in which the water is in-

Jan 1, 1958

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By C. A. Fothergill

An improved blotter model is described which makes use of a plastic sheet as base for the blotter field and pins to represent the input wells. The model is simple to construct and adapt and is particularly useful for demonstration purposes. Operational details are given. INTRODUCTION The blotter model was first applied to the investigation of oilfield problems by Wyckoff, Botset and Mus-kat,' primarily in order to demonstrate the flood patterns which could be expected from various arrangements of input and output wells in waterflooding projects. In recent years the model has been largely superseded for analog studies by the potentiometric and electric analog models which are more refined and versatile, since they can simulate the form, and, in certain cases, permeability variations which it is not possible to do with the blotter model. However, the latter is still used for analog studies where the reservoir can be represented as being uniform in thickness and permeability, and where a visual record of the flood advance is required. Ramey andNabor,2 for example, have applied the model to the investigation of areal sweeps in oil recovery by in-situ combustion. Because of its limitations, the blotter model can be used in general for only very simple arrangements of input and output wells, but within these limitations it has a definite advantage over all other types, in that it provides a picture of the advancing flood using the simplest and most easily constructed apparatus, by contrast with the gelatin model, for example, which requires more elaborate equipment. Moreover, the experiments can be quickly repeated and modified if necessary, whereas considerable time is required to prepare a gel field, compared with that required for the preparation of sheets of conducting blotting paper. For these reasons the blotter model can be very useful for demonstration and teaching purposes, enabling the student to experiment for himself with different arrangements of input and output wells. A model has been constructed for this purpose which is simple to operate and adapt. The model (Fig. 1) consists of a base platform or box, approximately 12-in. square, on top of which are screwed three lathes of 1/2 -in. square section to form three sides of a square 6 in. in length. This forms the support for a sheet of Cobex, transparent plastic, thickness .003 in., on which is carried the blotting paper representing the field. The plastic is flexible and relatively soft, and can be attached to the support by cellulose tape so that it can be easily removed when required. The input wells are represented by brass drawing pins pressed through the plastic sheet from the underside until the points are just projecting through the top; these are connected in the circuit as shown in Fig. 2. The sheet of blotting paper of required shape and size is saturated with a solution of 0.2 n-potassium sulfate to which has been added a saturated alcohol solution of phenol-phthalein at a strength of 10 cc/liter of stock solution. The surplus water is removed and the blotting paper placed in position on the plastic sheet making contact with the drawing pins and the sheet (which is an insulator). The anode consists of a second sheet of blotting paper cut as shown and saturated with the same solution. This is suspended from a laboratory stand, being connected to the conducting wire by means of a crocodile clip and making contact with the horizontal blotting paper at the projecting point. This is the method used by Ramey and Nabor and which permits the hydroxyl ions or colored front to reach the anode. As shown in Fig. 2, the electrical voltage used is 220-v DC and a shunt is placed across the terminals to step down the voltage as required. Further adjustment can be made as necessary using a lamp board in series with the shunt to obtain the

Jan 1, 1958

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

By J. S. Kasper, R. M. Waterstrat

IN view of the recent findings of a pronounced ordering of atoms in s phase alloys containing elements of the first long row of the periodic table (and including molybdenum),l it is of interest to resolve the question of ordering for s phases containing second and third-row elements. Examples of the latter have been provided recently by Greenfield and Beck2 and two of them, Re-Cr and Ru-Cr, would appear to be favorable for a study of ordering by X-ray diffraction methods because of the considerable differences in the scattering factors concerned. In addition, s phase is found to occur in the Os-Cr system, where the difference in scattering factors is even larger. Accordingly, X-ray powder intensities have been measured in an attempt to learn the nature of the ordering, if any, in these three v alloys. Since there is no reported work on intermediate phases in the Os-Cr system, an exploratory investigation was made in this system, and it was found that, in addition to the s phase, the phase with the A-15 or ß-W structure also occurs. Specimen Preparation—The alloys were prepared by compressing mixed powders of —200 mesh size and sintering in an atmosphere of pure dry hydrogen. All alloys were rapidly cooled from the annealing temperature to room temperature in a stream of cold dry hydrogen in a water-cooled chamber. Table I lists the sources and purities of the starting materials, as well as the details of processing for each of the alloys investigated. Intermediate Phases in the Os-Cr System—In the absence of information on intermediate phases in the Os-Cr system, it was suspected that this system would resemble that of Ru-Cr, where a s phase, RuCr2,2 and a phase with the A-15 structure, RuCr3,3,4 have been identified. Both these phases were found in the Os-Cr system and at compositions

Jan 1, 1958

By C. W. Spencer, K. A. Semlak, F. N. Rhines

IN an effort to obtain a better understanding of sintering in the presence of a liquid phase, it was decided to study the rate of capillary rise of a relatively low melting liquid metal in a higher melting metal powder compact. By assuming that the metal powder compact consists of a great number of parallel capillary tubes and that the flow of liquid

Jan 1, 1958

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By Strathmore R. B. Cooke, Iwao Iwasaki

RECENTLY spectrophotometry has been reported to provide a convenient technique for the rapid and reproducible determination of xanthate concentration in pulp solutions,12 and for a kinetic study of xanthate decomposition in acid solutions." Since the application of this analytical technique is feasible for those compounds showing pronounced light absorption maxima in the near ultraviolet region, it was deemed advisable to investigate the absorption spectra of some of the organic compounds that are used in flotation. It is known empirically that certain groups of atoms in an organic compound cause characteristic light absorption in the ultraviolet and near ultraviolet range, and the wavelengths and intensities of the corresponding absorption maxima are relatively independent of the nature of the remainder of the compound. The characteristic values of such groups, which are known as chromophores, are given in the literature.4,5 According to this information, many of the sulphydryl compounds are expected to show absorption maxima in the near or long wavelength ultraviolet region, whereas the saturated fatty acids and the saturated alkylamines do not. This article reports the absorption spectra of the six following types of sulphydryl compounds; mono-, di-(xanthate), and trithiocarbonates, dithiocarba-mate, dithiophosphate (aerofloat), and mercaptan. A Beckman DU quartz spectrophotometer was used to investigate the spectra in the wavelength region of 215 to 350mp. Materials: All the mono-, di-, and trithiocarbonates used in this investigation were prepared in the usual manner" from appropriate compounds obtained from Eastman Distillation Product Industries. The dithiocarbonates included the normal alkyl compounds from methyl to octyl inclusive, as well as the isopropyl, isobutyl, and isoamyl xanthates. Iodo-metric titration gave 99.7 and 99.5 pct purity for

Jan 1, 1958

By Paul B. Crawford, Bobby L. Landrum

An electrical model study has been mode to estimate the effect of horizontal fractures in thick reservoirs on pattern conductivity. For the patterns studied, it is shown that fracturing all the wells in the pattern in-creases the conductivity considerably more than frac-turing only single wells. For certain conditions one large fracture is more effective in increasing conductivity than several fractures of half the radius. Particularly in thick reservoirs and with large fractures, the center of the pay is found to be more responsive than other locations. For the seven-spot pattern fracturing the center well is more effective in increasing pattern con-ductivity than fracturing all outer wells with fractures of the same size. INTRODUCTION Although commercial fracturing has been used for some time very little quantitative information is known about the effects of fractures on reservoir behavior. The purpose of this work was to estimate the effect of horizontal fractures in thick reservoirs on the con-ductivity of various flooding and cycling patterns.2 Circular fractures originating at the wellbore and extending symmetrically into the pay were considered. ANALYSIS Electrical models were used in making this study. Horizontal fractures were simulated by copper sheets shaped like the fractures and of a proportional size; the wellbore was simulated by a copper wire. A dilute salt solution served as a conducting medium. A con-ductivity bridge was used to measure the conductivities of the various patterns studied. EFFECT OF HORIZONTAL FRACTURES ON CONDUCTIVITY Fig. 1 shows the effect on square and staggered line drive patterns of horizontal fractures located in the center of the pay. The model is shown schematically in the insert. The upper and lower groups of lines show the effect on conductivity when all wells are fractured, and when only one well is fractured, respectively. In general, pattern conductivities are substantially improved by fracturing all wells. Fig. 2 shows the effect of multiple horizontal frac-tures on the conductivity of a line-drive pattern. At

Jan 1, 1958

By L. J. Howell, R. C. Sommer, H. H. Kellogg

WORK described herein was undertaken with the aim of determining some of the physical-chemical properties of electrolytes suitable for the electrodeposition of pure zirconium metal. In this paper the phase diagram, vapor pressure, and activities in the melt are considered. In a companion paper,' the electrolytic conductivity of some of these melts is reported. The melts studied were mixtures of NaCl and/or KC1 with ZrC1,. Chloride melts were chosen for study because 1) if the electrolyte is to be useful for industrial electrodeposition of zirconium, the chlorides will be preferred to the relatively costly bromides and iodides; 2) fluoride melts were being studied in another laboratory (Horizons Inc., Cleveland); and 3) melts containing oxygen, in any form, are unsuitable for preparation of pure zirconium, because of the great affinity of this metal for oxygen. Unlike electrodeposition from aqueous solution, the fundamental behavior of fused-salt electrolysis is poorly understood. In most cases, such basic electrochemical information as the phase diagram of the melt system, activities in the melt, conductivity, the nature of the current-carrying ions, the equilibrium electrode potentials, and the overvoltage behavior of the electrodes is unknown to the researcher who would develop a new electrodeposition process employing a fused salt. This research project was designed to supply information about some of these basic physical-chemical properties so that an intelligent choice of electrolyte for electrodeposition studies could be made. Experimental The experimental difficulties-encountered in this work result from the properties of zirconium metal and ZrC1,. ZrC1, is a solid which sublimes at 334°C. It is rapidly hydrolyzed by moist air to HC1, ZrOCl,, and ZrO,. Unusual precautions were exercised in this work to prevent hydrolysis of ZrC1, and rigidly to exclude oxygen, nitrogen, hydrogen, and carbon from the melts under study. These elements are known to react with and contaminate zirconium metal. All melts were studied in vacuum systems, i.e., in the presence of ZrC1, vapor only. Transfer of ZrC1, to or from the melts was accomplished entirely by vacuum sublimation. In this way, neither the melts nor the ingredients thereof were permitted to

Jan 1, 1958

By R. Maddin, S. K. Tung

SUCCESS of the dislocation theory in formulating the transitional lattice theory proposed by Har-greaves and Hill in 1929' is well established for low angle grain boundaries. The theoretical work of Burgersa and Read and Shockley,3 together with the experimental observations of Aust and Chalmers4 and Parker and colleagues,6 leaves little doubt as to the structure of grain boundaries with differences of orientations up to between 15" and 20". Beyond these angles, the structure of the boundary is not so clear, and is still a matter for conjecture. There have been notable experiments devised from which the data could be used to calculate energetics for possible arrangements of atoms in forming a large angle boundary.6 Most of these experiments deal with diffusion through and along the grain boundary. The recent work of Rhines and Cochart7 and Rhines, Bond, and Kissel18 was concerned with the relative movement of grains in aluminum bicrystals under constant tensile loads with their boundaries aligned at 45 " to the tension axis. The gliding along the grain boundary was cyclic and began after an incubation period. The velocity of gliding increased with the sum of the angular difference, 8, between the operative slip direction in the conjugate crystals and the angular difference between the active slip planes as measured between their traces upon the grain boundary. The initial gliding rate varied with temperature, and the logarithm of the average gliding taken over a considerable period was a linear function of the reciprocal of the absolute temperature: the slope gave an activation energy of 11,000 ±1,000 cal per mole. Since the rate of grain boundary shear is sensitive to the misorientation of the grains themselves, as shown by several workers,7,8 it is suggested that further work of this type might be fruitful in adding information regarding the behavior of boundaries under stress. The techniques devised by Chalmers" added impetus to the facility for observing grain boundary behavior, in that they provided a simple means for producing bicrystals of predetermined orientation so that the angle of the boundary could be controlled,

Jan 1, 1958

By M. I. Sherman, J. D. H. Strickland

PRELIMINARY experiments in these laboratories showed that whereas pyrite1 produced only sul-fate the action of aqueous chlorine solutions on most other sulfide ores resulted in the formation of a mixture of sulfate and elemental sulfur, the production of the latter being favored by a very dilute solution of oxidant. The reactions taking place were obviously complex and only a detailed kinetic study could be expected to clarify the position and enable a prediction to be made of conditions leading to the rapid formation of metal salt and the economically desirable elemental form of sulfur. Galena was chosen for the first investigation as it is of widespread occurrence and is representative of a simple cubic lattice sulfide containing the monosulfide unit, S2-. Experimental Procedure The apparatus and general technique used in this work have already been described.' Analyses for chlorine and sulfate were carried out by the same methods as those used for pyrite. The lead in 1 ml aliquots of solution was determined polarographi-cally, after destroying chlorine with hydrazine hy-drochloride and making solutions 0.5 molar with hydrochloric acid. A large sample of Kansas galena, assaying at better than 98 pet PbS, was crushed and wet sieved to give fractions of —10 + 14, —20 + 28, —28 + 35, and —48 + 65 Tyler screen. The particles were almost perfect cubes and the apparent surface Per gram was calculated assuming each particle a cube Of side equal to the mean mesh opening. A volume shape factor, calculated as for pyrite, was exactly unity. The main apparatus was unsuitable for direct visual examination of the ore particles during the reaction. For this purpose a small cell from a Spekker Absorptiometer optical flats 1 cm apart) was l by a greased microscope slide after filling with oxidant solution. One or two ore particles were placed in the cell and the solution was stirred by a glass covered speck of iron wire activated by an external rotating magnet. The surface of an ore particle was examined under a binocular microscope at between 10 and 40 magnifications. Results Experiments were made under a wide variety of conditions, the form of presentation of the data being illustrated by Fig. 1, where the concentrations of chlorine, sulfate, and sulfur are plotted against time. The fictitious concentration of solid sulfur is used for convenience and is the molarity of sulfur which would be recorded if the elementary sulfur formed during the reaction were dissolved in the liquid iii the reaction vessel. As some lead sulfate is occluded with the sulfur on the ore particles the amounts of sulfur and sulfate formed during a reaction cannot be calculated

Jan 1, 1958

By A. F. Henderson, C. F. Cornell, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60' pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct —325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: I) high filtration rate—in terms of pounds of dry solids per hour per square foot of filtration area—at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of ' plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball .without enough green strength for the firing operation. Development work has met these objectives. At low investment and operating costs, filtration rates of 250 to 600 dry lb per hr per ft2 have been attained for concentrates of 60' pct —325 mesh. By combining the disk-type continuous filter with proper agitation, the Agidisc filter produces a homogeneous filter cake, easily discharged from the disk sectors. This application provides the lowest initial cost per square foot of filtration area, minimizes floor space, reduces down time for changing filter media to a negligible factor, and simplifies process control and maintenance for the operator. It is now possible to predict very closely the taconite concentrate filtration rates for a wide variety of conditions—either by experience or with a few simple leaf tests. When balling and pelletizing operations began on a continuous basis, it became apparent that moisture content of the filter cake was a critical factor and must always be controlled by the filter operator below some maximum allowable value. Accordingly the Reserve Mining Co. and the Eimco Corp. joined in a study of the many variables affecting filter cake moisture content. The study was conducted at the Reserve Mining Co. taconite plant at Babbitt, Minn. To process plant tonnage the Babbitt plant utilizes a 6-ft diam Agidisc filter with six disks and an 8-ft diam drum filter with 10-ft face. However, most of the plant filter investigations were made on the Agidisc because of its superior performance. A considerable amount of small-scale test work was first carried out to study more closely the individual variables and ascertain their effect on filter cake moisture content. A general correlation method was then developed which allowed reasonable prediction of moisture content at any operating conditions. This step was made necessary by the fact that in full-scale filtering, operating variables usually interact to produce a combined rather than a singular effect. Studies were then made on the full-scale filters to prove the validity of the correlations developed, and past operating records were examined to ascertain whether or not significant variations could be traced to any single factor or to a combination of factors.

Jan 1, 1958

By Rikuro Otsuka

TITANIUM is attacked slowly by hydrochloric acid," and corrosion rates decrease with time of exposure.' This behavior is due to the formation

Jan 1, 1958

By N. A. McKinnon, J. H. Auld, A. M. Marshall, R. A. Coyle

IN making a study of the slip deformation and strain hardening of single crystals of aluminum, it has been found that considerable information additional to that provided by the usual metal-lographic techniques can be obtained by the use of the microfocus X-ray method described by Schulz.1 This technique has been applied to crystals both in the state as-grown by the strain-anneal method and after they have been subjected to increasing amounts of plastic strain. Kelly and Wei" have recently reported the use of this method for a study of lineage structure in aluminum single crystals grown from the melt. The crystals, prepared from aluminum of 99.99 pct purity supplied by British Aluminium Co. Ltd., were grown in the form of flat tensile specimens with a gage section of 0.3 by 0.1 in. and a gage length of 2.3 in. The microfocus X-ray tube used provided a focus of approximately 50 half width. Examination of a large number of as-grown crystals showed no sign of any macroscopic defects in the majority of cases. However, occasionally crystals grown by the strain-anneal method did show defects similar in nature to those shown by Kelly and Wei to occur in crystals grown from the melt. In some other cases a more regular appearance of black and white lines, corresponding to valleys and ridges, respectively, in the lattice, was obtained, Fig. 1. This particular crystal was slightly deformed as the lines when present in the image of an as-grown crystal are only barely visible. The angle of tilt of the blocks is of the order of 3. It seems likely that these tilt boundaries arise during the growth of the crystal due to the specimen not being perfectly flat on the hearth of the furnace and straightening under its own weight at the elevated temperatures. For the deformation studies the crystals were strained in a Polanyi-type tensile machine. A typical photograph taken after 1.2 pct elongation of a single crystal oriented with its axis fairly close to the center of the stereographic triangle is given in Fig. 2. The reflection, which is from the (111) planes, is traversed by two systems of parallel lines. These have been identified as traces of the primary (111) slip plane and the (110) plane perpendicular to the primary slip direction. The latter lines correspond to kink bands which could not be detected by the ordinary techniques of

Jan 1, 1958

By W. R. Hibbard Jr., T. Michalak

THAT the amount of deformation and annealing time influences the recrystallization temperature of cold-rolled copper has been well established. Evidence that the recrystallization temperature can be affected by the deformation texture has been reported by Brick and Williamson,% ho found that copper straight-cold-rolled to 99 pct reduction to produce one deformation texture and copper cross-cold-rolled to 99 pct reduction to produce a second and different deformation texture correspondingly recrystallized at different temperatures to different textures. The purpose of the present work was to study more thoroughly the effect of the deformation texture on the recrystallization of cold-rolled copper. Experimental Procedure The copper used in this investigation was commercial OFHC copper (nominally 99.985 pct Cu) in the form of 0.500-in. plate. Qualitative spectro-graphic analysis showed only a slight trace of iron and a trace of silver. No analysis was performed to determine the exact content of the iron and silver,

Jan 1, 1958

By H. C. H. Darley

Particles of montmorillonite-type clays consist of plate-like clay crystals stacked face to face. Under certain conditions in a suspension, these particles disperse to individual platelets with the formation of diffuse double layers round each platelet. This action has a profound influence on the rheo-logical and other properties of the suspension. This paper describes a test for degree of dispersion and uses this test to correlate changes in dispersion with changes in viscosity and gel strength. The test is of practical value in determining and controlling dispersion in drilling muds. INTRODUCTION It has long been recognized that the hydration and dispersion of clays, particularly those of the montmoril-loilite type, strongly influences the rheological and other properties of drilling muds, but little has been done to measure either of these phenomena under conditions that exist in drilling muds. The hydration of clays as such has been extensively studied by those interested in clay mineralogy, but in drilling muds it is to be expected that dispersion is at least as important a factor as hydration because of the much higher water-to-clay ratios and the very high degree of mechanical agitation. The term dispersion as generally applied to colloidal systems means the subdivision of large particles to small. Particles of montmorillonitic clays, however, consist of plate-like particles stacked face to face. Dispersion of these aggregates to individual platelets may be expected to have an unusually large influence on the properties of the suspension because of the shape factor, the enormous increase in specific surface, and the pronounced surface phenomena exhibited by the crystal surfaces. It is this form of dispersion that is particularly considered in this paper, -and the term degree of dispersion is used to imply the number of platelets per particle. The term aggregation is used to denote the opposite of dispersion, the association of individual platelets face to face to form stacks. It is important, as Garrison' has pointed out, to distinguish between the deflocculation-flocculation phenomenon and the dispersion-aggregation phenomenon. Flocculation of clay suspensions is characterized by the formation of voluminous sediments that are stable under quite high centrifugal fields. This indicates an edge to plate association of particles to form an open network type of structure, which obviously will have quite a different influence on the properties of the suspension than aggregation of the platelets face to face. The work described in this paper was primarily concerned with developing a test for degree of dispersion in clay suspensions and by means of this test to follow changes of dispersion brought about by addition of electrolytes and to show the influence of dispersion on the rheological properties. The Clay-Volume Test This test is based on the assumption that the greater the number of particles per unit weight of clay in a suspension the greater will be the volume of sediment when it is flocculated under standard conditions and centrifuged. After considerable experimentation the following procedure was established: 1 cc of the test mud vigorously shaken with 100 cc of 1-N NaCl in an ASTM oil centrifuge tube and centrifuged for five minutes in an International No. 2 centrifuge at 2,000 rpm. When drilling fluids of different solids content are being compared, the clay volume is expressed in cc per gram of clay solids, but generally changes in dispersion in a given mud are being compared and it is more convenient to report as cc of sediment. The test is strictly a comparative test, so that it is not necessary to adhere to the conditions specified above, e.g., with field muds a stronger flocculant such as Al2(SO4)3 may be preferable to NaCl.

Jan 1, 1958

By L. K. Jetter, C. J. McHargue

DEVELOPMENT of preferred orientation in uranium is of interest because of the strongly anisotropic properties of the orthorhombic crystal structure. Harris&apos; reported inverse pole figures for rolled uranium rods which showed <010> and <410>* to be parallel to the rolling direction after On 0.19-in. spherical X-ray diffraction specimens taken from the center of the middle section of each rod, pole distribution data were obtained by the spectrometric method described previously.4 The specimen was rotated rapidly about the axis coinciding with the rod axis in order that a large number of grains could be scanned and was rotated slowly about an axis perpendicular to the rod axis. The variation in the diffracted X-ray intensity was recorded as a function of the latter motion (angle 4). Fiber-axis distribution charts (inverse pole figures) were prepared by the method described by Setter, McHargue, and Williams." After having been corrected for background radiation, the pole distribution data (I vs ?) were normalized. A normalizing factor for each plane has been shown to be Iranaom = f I sin 4 ? 4 and was obtained by graphical integration from the data for that plane plotted as I sin ? vs ?. The axis-distribution charts deduced from the normalized pole densities are shown in Figs. 1 to 3. On these charts, the contours indicate angular positions of equal normalized axis density,

Jan 1, 1958

By T. V. Philip, Paul A. Beck

IN a previous note1 it was pointed out that the available information suggests a distinct correlation between the occurrence of the CsCl-type ordered structures formed in equi-atomic binary alloys of transition elements and the location of the components in the periodic table. A definite increase in the bond strength between unlike atoms, as compared with that between like atoms, is indicated when, in binary alloys of iron group elements, the other component is changed from chromium to vanadium or tantalum, to titanium. Laves and Wallbaum,2 eported a CsCl-type ordered structure for the stable intermediate phase at the equi-atomic composition in the Ti-Fe system (and also in the Ti-Ru and Ti-Os systems). On the other hand, Tagaya, Nenno, and Nishiyama8 found no ordering of this kind in the body-centered-cubic solid solutions in the Cr-Fe system. It was concluded&apos; that the occurrence of a CsC1-type ordered phase of intermediate stability may be expected in the V-Fe system. Preliminary results were described: suggesting that at least some degree of order does exist in the equi-atomic alloy VFe, annealed at 1200° C and quenched in cold water. Using CrK radiation, at least one weak superlattice line was found in the X-ray diffraction pattern which could be indexed as (100). and which disappeared, as expected, when FeK radiation was used. It was found more recently that the impurity phase (presumably VN), previously giving rise to additional X-ray diffraction lines and thus preventing definite indentification of the (111) superlattice line,&apos; can be eliminated by preparing the alloy by arc melting in a helium atmosphere. The alloy specimen melted in this manner had clean surfaces and showed very littte, if any, nitride phase in the microstructure after annealing in vacuum at 1250°C and quenching. The relative intensity of the (100). superlattice line with CrK radiation was greatly increased and, in addition, a fairly strong (Ill) , superlattice line and even a detectable (210) , super- lattice line was obtained, when the powder produced by filing from the 1250°C annealed and quenched specimen was reannealed in vacuum at 625°C for 1 hr. By using a cellulose acetate film as a filter in front of the photographic film in order to absorb the soft radiation resulting from air fluorescence, the background intensity could be reduced considerably in relation to the intensity of the diffraction lines. All three superlattice lines, (100),, (111)., and (210)a, disappeared, as expected, when a radiation other than CrK, was used.1 For the powder reannealed at 625ºC, the strongest lines of the s pattern also appeared weakly, indicating that during an: nealing at 625°C a small amount of transformation took place from the body-centered-cubic to the u phase. However, since all superlattice lines to be expected in the 0 angle range used were actually very clearly present, it was evident that the high temperature body-centered-cubic phase had transformed into a CsCl-type ordered structure before much s phase could form. Reannealing filings for 1 hr at 700°C resulted in complete transformation into the u phase. After 1 hr at 650°C the transformation into IT was not quite complete, the strongest body-centered-cubic diffraction lines were still present, although fairly weak, and only the (100), super-lattice line was detectable (extremely weak). These findings not only confirm the previous conclusionsL as to the existence of a CsCl-type ordered structure in the Fe-V system, but they also indicate that this metastable ordered structure forms at about 600°C preceding the formation of the stable s phase, while at 1250°C the disordered body-centered-cubic phase is stable. The faint (loo) , super-lattice line previously observed in specimens quenched from 1200°C was probably due to the fact that the quenching of the powder in an evacuated fuse:! quartz capsule was not fast enough to prevent completely the ordering reaction on cooling. The present results conform with the suggestion that the A-B bond, in relation to the A-A and B-B bonds, increases in strength from CrFe to VFe to TiFc. It is, therefore, of interest to compare the measured values of the average atomic diameter for these three alloys with the corresponding average atomic diameters calculated from the atomic radii of the elements concerned. ASSUming A-B contacts

Jan 1, 1958

By J. A. Marton, N. Brown, M. Herman

AT high temperatures a deformed polycrystalline metal shows grain-boundary displacement in preference to slip lines.&apos; This has led to the conclusion that overall strain at high temperatures is produced chiefly by grain-boundary displacement. Detailed microscopic examinations of individual grain boundaries have shown many interesting ways by which their displacement occurs; sometimes no grain deformation was observed except possibly in the immediate neighborhood of the boundary. However, X-ray examinations show that at high temperatures subgrain formation occurs;Y he process, generally called polygonization, results from lattice bending and the subsequent climb of dislocations to form low-angle boundaries. Quantitative measures of the grain-boundary displacements show that they make a minor geometrical contribution to the overall strain; the major contribution is made by grain deformation."&apos;" A relationship between grain-boundary displacement and grain deformation was suggested by McLean, who showed how the degree of polygonization would determine the amount of grain boundary displacement: and by Dorn, who showed that for a given creep stress, the amount of grain-boundary shear was related to the overall strain and was independent of temperature.&apos; Although the grain-boundary displacement may make a small geometrical contribution to overall strain, it may still be the rate-controlling factor in high-temperature creep. If in general grain-boundary displacement and grain deformation are dependent quantities, then the designer of a creep-resistant metal would like to know whether it is more desirable to strengthen the matrix of the grain or to increase the strength of its boundary. The widespread interest in the relationship between temperature and grain-boundary displacement makes it desirable to test the generality of Dorn&apos;s result6 that the ratio of grain-boundary displacement to overall strain is independent of the temperature for a given creep stress. In this investigation p-brass was used because it produces sharp grain-boundary displacements above 400°C. Since B-brass undergoes an order-disorder transformation which abruptly strengthens the grain, it is an excellent metal for determining whether grain-boundary displacement or grain deformation is the rate-controlling factor in creep. The problem will be confined to the temperature range where

Jan 1, 1958