Search Documents

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By Jens P. Nielsen, W. H. Justice

This paper describes an improved acidizing technique which has been applied in acidizing gas wells in the La Gloria Field. Wells acidized in this manner exhibited a much greater increase in deliverahility than wells acidized in the conventional manner. The acid is injected into the well in small slugs separated by a small volume of high pressure gas. The acid and gas are displaced from the tuhing by high pressure gas to reduce the hydrostatic head on the well when the acid is recovered from the well. The well is opened for production as soon as the acid and gas are displaced. This procedure permits a very rapid recovery of the acid which results in large increases in the deliverability of the gas wells. It has been found advantageous in the acidization of gas injection wells to inject the high pressure gas directly after the acid without backflowing the acid out of the well. This practice has made it possible to inject the gas in the injection wells of this field with a much lower pressure differential. This reduces the horsepower required to inject the gas and also decrease:, the number of injection wells required per reservoir. INTRODUCTION The results obtained by acidizing gas wells ill the La Gloria Field have varied considerably in the past. For this reason. a planned study of the acidizing procedure was undertaken in order to obtain more consistent results. The Frio Sands of the La Gloria Field are rather permeable and it was not necessary to acidize many of the wells when they were originally completed. At the completion of an eight-year cycling program in several of the gas reservoirs, it became necessary to recomplete many wells in other reservoirs. It was found that the opan Flow potential of the wells recompleted in different sands was not as large as wells that were originally completted in that reservoir. A study of the drilling records of several of these wells indicated that the sands had originally been subjected to considerable hydrostatic drilling fluid overload while the well was being drilled to the deeper sands of the field. It is indicated that during this eight-year period, the drilling mud and water that were lost into the formation when the well was being drilled had formed a relatively impermeable Eone around the well bore. This impermeable zone around the well bore made it very difficult to obtain high deliverability wells when the original wells are recompleted in other zones. Muskat' has shown that in uniformly permeable and porous formations a zone of partial plugging one ft in radius around the well would drastically decrease the productivity of the well. The analysis for this problem shows that the production capacity of a well is very sensitive to the value of the permeability of the zone immediately surrounding the well bore. This is to be expected in view of the highly localized character of the pressure drop in a radial flow system about the well center. The reduction of the deliverability is not proportional to the thickness of the mud-affected zone as the major portion of the reduction in deliverahility IS caused hy the

Jan 1, 1952

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

By Alan Probert

IN his inaugural address in 1949, President Truman made a policy declaration which launched the foreign technical assistance program known to the world as Point Four. Congress passed Public Law 535 defining the scope of the program and holding activities to certain limitations. It also provided $34.5 million for the first fiscal year. The Technical Cooperation Administration was established within the Department of State to coordinate and direct a program to include "economic, engineering, medical, educational, agricultural, fishery, mineral and fiscal surveys, demonstration, training and similar projects." The mineral programs of Point Four have been staffed and managed by two agencies of the Department of Interior, the Geological Survey and the Bureau of Mines. The Geological Survey is concerned primarily with water-supply problems, the discovery of mineral deposits, and the determination of habit, shape, and grade of mineral deposits. The Bureau of Mines is concerned with determining the commercial potentialities of mineral deposits, mineral technology, and the production and distribution of mineral commodities. Mineral projects comprised only 1 pet of the first year's budget. In spite of the relatively insignificant expenditure compared to those for food, agriculture, and health, a commendable record has been achieved.

Jan 1, 1952

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors' reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952

1944. Walter Hull Aldridge New York, N. Y. 1946. Peter M Anderson Johannesburg, South Africa 1946. Charles Camsell Ottawa, Ont. Canada 1946. Charles Augustus Carlow Fife, Scotland 1949. Erie Victor Daveler New York, N. Y 1946. Cecil H. Desch London, England 1946. William Fraser London, England 1917. Herbert Hoover New York, N. Y. 1941. Daniel Cowan Jackling San Francisco, Calif. 1939. Henry Krumb New York, N. Y. 1942. Essington Lewis Melbourne, Vic., Australia 1921. C. McDermid London, England 1944. Walter C. Mendenhall Washington, D. C. 1942. Paul Dyer Merica New York, N. Y. 1938. A. M. Portevin Paris, France 1934. T. A. Rickard Victoria, B.C., Canada 1946. John R. Suman Houston, Texas 1946. Wen-Hao Wong Chungking, China

Jan 1, 1952

Considerable discussion took place at the June 18th Board of Directors Meeting concerning ways the Petroleum Branch office in Dallas could better serve its members and the essentially Petroleum Local Sections, namely the Delta, East Texas, Gulf Coast, Kansas, Mid-Continent, North Texas, Oklahoma City, Permian Basin, and Southwest Texas. The question of whether decentralization strengthens or weakens the Institute was debated, particularly as to what services could be advantageously decentralized and how both offices could keep informed on their mutual problems. Among other things, it was decided that an Auxiliary Admissions Committee could screen applications from Petroleum members before final action by the National Admissions Committee in New York. Finally it was voted, "That all administrative matters that can be properly delegated to a Branch organization may be so delegated". Final details were approved at the July 16th meeting of the Executive and Finance Committees.

Jan 1, 1952

Institute of Metals - Iron and Steel - Mineral Industry - Industrial Minerals Year ?Division - Petroleum Division ? Division - Coal Division - Education Division -Division 1918 W M CORSE 1919 1920 W. H BASSETT 1921 1922 W B PRICE RALPH ARNOLD 1923 E DEGOLYER 1924 G K ELLIOTT 1925 F JULIUS FOHS 1926 PAUL D MERICA 1927 JOHN M LOvEJOY 1928 S SKOWRONSKI A W AMBROSE RALPH H SWEETSER

Jan 1, 1952

By Wallace W. Wilson

The Cook Ranch Field produces from a very permeable lens of Cook Sand of lower Permian or upper Pennsylvanian age, occurring at an average depth of 1.300 ft. The field was discovered in 1926, and has been operated with low pressure gas injection since July, 1927, one of the first such projects in Texas. Cumulative recovery to Dec. 31. 1950, was 14,701,131 bbl of crude oil, an average of 1,013 bbl per acre-ft of oil rection. and 72.5 per cent of the oil originally in place. Analysis of the reservoir performance indicates that grav-ity drainage has been an important factor in the producing mechanism. The high permeability and uniformity of the reservoir were extremely Favorable tor this type of operation. INTRODUCTION The Cook Ranch Field is the largest of a number of relatively small, shallow producing areas near .Albany, in Shackelford County, Texas. This field is one of the first to be operated by gas injection in Texas, and probably is the most successful low pressure gas injection project ever attempted. The field is owned entirely by Koeser and Pendleton, Inc., and Continental Oil Co., and has been operated by Roeser and Pendleton, Inc., since it was discovered. This study has been made possible through the cooperation of Roeser and Pendleton, Inc.. in making availahle a remarkably complete set of records covering all phases of their operations. The purpose of this paper is to present a summary of the history of the operations through Dec. 31, 1950, and to analyze some of the factors which appear to be responsible for the success of the project. Information concerning the physical plant and the early gas injection history has been presented in an earlier paper.' RESERVOIR CHARACTERISTICS production in the Cook Ranch Field is from a large lens of Cook Sand. of lower Permian or upper Pennsylvanian age, occurring at an average depth of 1.300 ft. The average dip of the sand body, as shown in Fig. 1. is only about 50 ft per mile to the northwest. The reservoir has an area of 930 acres and contains 15,512 acre-ft of Sand, consisting of about 14.512 acre-ft of produc-tive oil zone. and an estimated 1.000 acre-ft of primary gas-cap. The iso-pachous map (Fig. 2) was prepared from drillers' logs. Recent coring in the field has proven these logs to be quite accurate. The productive limits of the field are defined by shale on all sides but the southwest where a small zone of edgewater was encountered. This water does not appear to have encroached into the reservoir, and water production has been small. A smaller producing area to the south of the Cook Ranch Field also produces from the Cook Sand. but is separated from the reservoir under consideration by a band of shale. The sand consists of well sorted, coarse grained. rounded and subangu-lar quartz fragments. very poorly cemented. The analysis of 46 chip-core samples from two recently completed test wells indicates a range of porosity values between 12.5 and 28.2 per cent. wit11 an arithmetic average of 24.0 per cent. Air permeability values range between 50 and 2,300 md, with an arithmetic average of 1.200 md. The reservoir where cored is a Solid sand body. with no discernible major shale breaks or impermeable streaks. Vertical permeability appears to be of the same magnitude as the horizontal permeability. A core of the Cook Sand was cut ill the smaller field to the south, using lubricating oil as drilling fluid. The connate water content of the sand in this core was found to average about ten per cent, and the porosity and permeability were comparable with the values reported above. No analysis was made of subsurface or recombined hydrocarbon samples,

Jan 1, 1952

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed. Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank, or at any time in batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume1,2 or a relative concentration, which will be a function of the recovery." A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the data. One of these, the initial concentration or proportion of floatable mineral, is not necessarily equal to the feed assay because of nonfloatable oversize or locked particles." The other, a rate constant, is a measure of proportionality between the rate and the pulp property on which the rate depends. The value of the rate constant will be determined by the values of all variables which control the process and will be changed by significant changes in any of them. It is, therefore, a direct measure of performance. Where recovery or grade change continuously with flotation time, the rate constant will be independent of time and will characterize the entire course of the separation. Development of Rate Equations Rate equations can be developed either by analysis of the mechanism of the process or by direct fitting of equations to recovery-time data. Sutherland's attempt by the first method' suggests that the effect of particle size variation on the rate complicates the derivation of a simple equation applicable to an ore pulp. A further problem with an ore is the concentrate grade requirement, which usually involves a variable rate of froth removal. Thus the final rate for any cell may depend on the froth character and froth height, as well as on the pulp composition. This does not imply that each cell cannot reach a steady state2 in which the rate will depend ultimately on pulp composition. The second method is the fitting of rate equations consistent with the necessary boundary conditions* to experimental recovery-time curves. On the assumption that under constant operating conditions the flotation rate is proportional to the actual or relative concentration of floatable mineral in the pulp, a generalized rate equation may be expressed as follows: Rate = Kcn [I] where K is the rate constant, c is some measure of the quantity of floatable mineral in the pulp at time t, and n is a positive number. In previous rate studies, the value of n has been taken as 1, either by direct assumption," or as a result of the hypothesis that bubble-particle collision is rate determining.' A first order equation results, which after integration in terms of cumulative recovery R, leads to Loge A/A-R = Kt [2] The quantity A is the maximum possible recovery with prolonged time under the conditions used. No conclusive proof for the validity of this equation in flotation has been advanced. The evidence cited in its support consists entirely in the demonstration that it appears to apply to a limited number of recovery-time curves."' It will be shown subsequently that this procedure is not sufficient to establish the order of a flotation rate equation. The possibility that the equation may be of higher order therefore requires examination. If, in particular, the exponent in eq 1 is assumed to be 2, then after integration there results R = A2Kt/1 + AKt [3] with K again a rate constant and A the maximum proportion of recoverable mineral. Eq 3 may be

Jan 1, 1952

[Allen-Sherman-Hoff Pump Co. Third Cover Dee Carlton Brown. Advertising Allis-Chalmers Mfg. Co. 110 Compton Advertising, Inc. American Cyanamid Co. * James J. McMahon. Inc. American Manganese Steel Div., American Brake Shoe Co. 138 Fuller & Smith & Ross, Inc.]

Jan 1, 1952

By Terkel Rosenqvist

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann's finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author's reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp p/RT, where p is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf's can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By Nathaniel Arbiter

T. M. Morris (School of Mines and Metallurgy, Rolla, Mo.)—Rate studies promise to help quantify flotation operations. The author's exposition of rate studies is therefore laudable. However his exposition of a second order rate equation rather than a first order rate equation is not convincing. It is important to use the correct equation, otherwise erroneous conclusions may be drawn. The data assembled by the author and plotted according to a second order rate equation can be plotted according to a first order rate equation. As a matter of fact much of the data used reveals that a second order rate equation is not applicable. According to the method used by the author for plotting data, the reciprocal of the slope of the line is the maximum possible recovery. Physically this cannot exceed 100 pct, yet several graphs yield maximum recoveries greater than 100 pct. For example: l—Curve 2, Fig. 1 yields a value of 120 pct; 2—Curve 2, Fig. 2 yields a value of 115 pct; 3—Fig. 7 yields a value of 110 pct. The real test of the graphical method is, as the author points out, whether or not the earliest points agree with a straight line. The second order rate plot does not fulfill this requirement. Fig. 10 shows the data used by the author to obtain Curve 2 in Fig. 1, plotted according to both a second and first order rate equation. Fig. 11 shows the two rate plots made from data published by Ludt and DeWitt.19 In Fig. 10 the first order rate plot gives a very good fit and obeys the boundary condition of passing through the origin. For the second order rate plot a straight line can be drawn through the last three points but the earliest points are not in agreement with this line. The reciprocal of the slope of the straight line gives a value of maximum possible recovery of 112 pct. The maximum possible recovery according to the first order rate plot is 78 pct. In Fig. 11 the first order rate plot again fits all of the points very well and passes through the origin. The second order rate plot shows wide deviation of the earliest point, indicating that the second order rate equation is not applicable. The reason for the fit of data to the second order rate equation during longer flotation times is that R, the cumulative percent recovery, changes slowly toward the end of the flotation operation, so that when t/R is plotted against time, one is, in effect plotting t against t and one would certainly expect a straight line. The author attempts to show that the second order rate equation is correct by citing evidence which shows that recovery is a function of initial concentration. This is a debatable point especially since, in the author's original presentation of this paper at the St. Louis

Jan 1, 1952

THE Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City United Engineering Trustees, Inc. When Mr Carnegie made his gift, "for the erection of a suitable union home" for the engineering societies, United Engineering Trustees, Inc (then United Engineering Society) was chartered under Chapter 703, Laws of the State of New York, 1904, for "the advancement of the engineering arts and sciences in all their branches, and to maintain a free public engineering library" The Corporation was further empowered to acquire real and personal property and to use, maintain and occupy it, with the provision that any building erected by the Corporation shall be used perpetually as a meeting place and headquarters for the Founder Societies Thus the Carnegie gift realized the ideal of bringing the engineering societies together under one roof, and the Corporation through its members nominated in equal numbers by the four Founder Societies had the necessary authority to act for the Founder Societies in their joint interests in owning and operating for them not only Engineering Societies Building, but in the course of time, Engineering Societies Library, and

Jan 1, 1952

By C. G. McLachlan

ONE phase of the treatment in sulphide flotation, covered generally in a review of pulp pretreat-ment by S. A. Falconer,' is the matter of grinding mills as conditioners, a subject on which further study could be advantageous. Flotation with few exceptions is preceded by grinding, and the grinding and flotation capacity required for the treatment of an ore is based generally on laboratory or pilot mill tests. The results of such tests, it then is assumed, will be duplicated in practice, and a flowsheet is prepared on that basis. This assumption may be too broad, because in several instances laboratory flotation tests made on massive sulphide copper ores could not be duplicated in plant operation without the introduction of an aeration step, either in closed circuit with the grind-inging mills, or between grinding and flotation.~' " The differences between laboratory and plant grinding practice are considerable, and may be summarized as follows: 1—In the laboratory a relatively fine charge is ground in a batch mill. In the plant, the feed, usually considerably coarser than the ore tested in the laboratory, enters the grinding mill continuously and more often than not, oversize material in the mill discharge is retained in the grinding circuit by a classifier until the required degree of reduction has been effected. 2—The rate of grinding in the laboratory is slower than in plant practice. 3—The percentage of volume occupied by the pulp in a laboratory mill rarely approaches that of a continuous overflow type mill. This does not apply if the comparison is made with grate type mills, but in that case an even wider discrepancy between the relative rates of laboratory and mill grinding almost invariably exists. The present trend in grinding is toward larger mills to reduce the number of operating units. This accentuates the foregoing differences. It is believed that the trend toward larger mills is sound, but that when large mills are used, metallurgists should check their flotation circuits carefully to determine whether laboratory tests are being reproduced in

Jan 1, 1952

By Robert Glass Cleland

Jan 1, 1952