Search Documents

By D. Malhotra, R. M. Hoover, F. N. Bender

The paper discusses the effect of aeration and agitation on grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." Analysts of flotation results indicate that molybdenite has fast floating and slow floating components. The rates of fast floating components, which do not create a problem inflotation, could be varied by changing agitation or airflow rates. However, the rate of slow floating components was stable and was only a function of residence time. Aeration has a significant effect on the grade of MoS2 and only a slight effect on the recovery of MoS2. Agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits are also considered.

Jan 1, 1981

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Walter von der Linden

INTRODUCTION There are three essential components for a modern longwall mining system: the coal cutting/loading machine, the self-advancing supports and the longwall conveying system. The latter consists of a face conveyor, a stageloader and a belt tall section arrangement (Figure 1). The longwall face conveyor is an integral component of the face equipment and has a threefold purpose: 1) continuous coal haulage. 2) track for cutter/loader . 3) reference/anchor rail for roof support advance. Further requirements for the longwall conveyor are horizontal flexibility for conveyor advance without interruption of haulage and cutter/loader tramming and vertical flexibility to cope with seam undulations.

Jan 1, 1981

By Louis A. Panek

INTRODUCTION AND SUMMARY With respect to the geomechanics aspects, the primary technical objectives in mining by an undercut-cave method are to achieve a controlled, sustained caving of the mineral body and to remove the fragmented ore with a minimum of dilution from surrounding unmineralized rock, while maintaining stability or control of the rock structure around the access openings. The structurally ideal ore body probably does not exist. If the rock mass is so weak as to cave on a short span, it may tend to be too sticky for easy drawing and handling, or create special problems in regard to support of the access openings. If the ore is strong, caving may be difficult and the caved fragments may be of such a large size as to require special equipment for transferring the ore from the caved zone. Given enough time and money to generate data and conduct trials, engineering and ingenuity can devise an appropriate combination of mine layout, sequence of extraction, and mechanical equipment to achieve a technically successful caving extraction operation to meet the foregoing requirements in many types of deposits. The large capital investment involved, however, reduces the freedom to make major changes once the mine development is well under- way, and the penalties for failure to accurately anticipate operating conditions militate against selecting any but the most obvious candidates for mining by an undercut-cave method. The demonstrated capability to extract large, deep, economically marginal deposits by this low-cost, high-volume method of mining provides an incentive to develop a rationale for predicting the cavability and stability characteristics of a deposit prior to mining, so that the undercut-cave method may be extended to a much wider range of mineral deposit characteristics. The ultimate goal is to establish as explicitly as possible the quantitative interrelationships between the measured rock-mass characteristics, the caving span, the size distribution of caved ore fragments, and the sizes and locations of stable access openings. Lacking an understanding of these relation- ships, a designer may readily change some factor in the wrong direction (e.g., excessively reduce the distance between the extraction level and the undercut to increase the convenience of operations for the undercutting crew, increasing the frequency of repairs to the extraction-level support system) or create unnecessary problems elsewhere in the system by introducing a design change that can achieve only minimal improvement in the factor of direct interest (e.g., unnecessarily complicate the ore-transfer system by changing the orientations of the openings, with- out succeeding in the objective of improving the ground support conditions). Although successful predesign is the prime objective, subsequent modifications in mine lay- out and sequence of extraction operations are inevitable. In developing the modified solution, systematic experimentation based on an understanding of the underlying structural relationships, coupled with monitoring measurements of selected diagnostic structural-behavior parameters, can achieve an acceptable solution in a minimum number of steps, which is far superior to the typical operational trial-and-error approach, in view of the cost of implementing each successive change. Since a drill-core sample of ore rock from a successful undercut-cave operation may exhibit a uniaxial crushing strength in excess of 100 MPa, the caving of such a rock mass is now commonly believed to be ascribable to the presence of discontinuities such as joints or fractures throughout the ore body. An essential part of the present investigation was therefore to characterize the natural discontinuities at each of the test sites by measuring their attitudes and spacings. The term "fracture" is used herein in a general sense to include any planar discontinuity without implication as to its suggested mode of origin. Most, but not all, of the fractures are properly termed joints. As a point of departure we may consider the possibility that the rock mass is transected by three families of joints, each family possessing a distinct orientation, such that parallelepipeds of intact rock are delineated by the jointing. Even if cementation is absent between adjoining parallelepipeds, the undercutting of the rock mass will not necessarily initiate sustained caving--owing to the all-around confinement, an arch may tend to stabilize over the undercut unless prevented from doing so by the failures of key blocks of intact rock. Thus, although the jointing can be assumed to weaken the rock mass, creating preferred directions of

Jan 1, 1981

By Torres S. Ricardo, Encina M. Víctor, Segura O. Claudio

INTRODUCTION This paper is a conceptual resume of engineering studies that have been evaluated by the Mine Department related to production planning over the next twenty-five years. These studies have been required principally because: a) The Rio Blanco Mine, property of CODELCO- CHILE, Andina Division, faces an operational problem due to heavy snowfall in winter which enters the surface subsidence area of the cave; later melts and filters into the broken ore creating a product that is difficult to transfer through the orepasses. The phenomenon is especially serious during the spring and has been increasing over the years. This element that complicates extraction will be controlled with the procedures proposed or others that may be determined in the future. b) The mine will increase production in 1985 by 40% . LOCATION The deposit is located in the central region of the Andes Cordillera, at an altitude of approximately 3,600 m above sea level, 50 km to the northeast of Santiago. The main camp is Saladillo (at 1,300 meters above sea level) located 30 km from the mine. Due to its location, the mine is subject to heavy snow storms during the year. On many occasions the road from Saladillo to the mine is closed because of storms and avalanches. For this reason the company has self-sufficient civil facilities near the mine to cover the needs and welfare of the working force. These housing facilities are connected to the mine by underground passages. For the same weather related reason the primary and secondary crushers, and the entire concentrator complex are located underground. GEOLOGIC CHARACTERISTICS Geology Based on the geologic model developed for the Rio Blanco deposit and comparing it with standard models pertaining to copper porphyries, it can be concluded that this deposit is part of the apical sector of a mega deposit and therefore the projections of the Xio Blanco cop per mine are very favorable, both in lateral area and depth. In order to confirm and evaluate these geo- logic features, an extensive drilling program was started at the Rio Blanco deposit. Diamond drill holes were drilled to depth as well as in the areas named "La Americana", "Don Luis" and "Elguin". The area explored by the drill program is 3 km long in a north-south direction and 1.5 km wide in an east-west direction. In some sections the drilling in depth reached the 2,300 m elevation mark. The lowermost level in the mine is at elevation 3,070 m. These new studies have permitted the recognition of the following lithologic units: Andesite Andesite Breccia Granodiorites, Rio Blanco and Cascada Granodiorite Breccia Quartzmonzonite Porphyry Monzodiorites and Latites Tourmaline Breccia Dacite Pipe and Rhyolite marginal ring. The mineralogical study permits the definition of three stages of hypogene and hydroterma1 alteration of importance with a time-altered sequence. These stages correspond to a late hydrothermal stage. The kinds of alteration that have been recognized are: Potasic Alteration Propylitic Alteration

Jan 1, 1981

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By Joseph A. Gill, Ernest A. Curth

The Government and Leeco concluded a cost-sharing agreement in 1976 to demonstrate longwall mining of a thin coalbed, 1 m or less, in a mine near Hyden, Ky. A premining investigation laid the groundwork for mine design and equipment specifications. Four- legged shields, a face conveyor, a stage loader and an in-web shearer were selected to operate on a 183 m face. Lengwall mining began in 1979 and initially was slowed by low mining height and equipment problems. A rock mechanics program provides early warning capability and criteria for future mine design. Monitoring of surface effects is included.

Jan 1, 1981

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

By W. L. Chen

The Batac jig was first introduced in the US for fine coal cleaning in 1973 (Tackett, 1977; Hake, 1976). Since then, a total of six such jigs of various sizes have been installed in five US plants for a total capacity of 2346 t/h. The raw coal size ranges from 19 mm x 0 to 9.5 mm x 0-fraction sizes previously fed to heavy medium cyclones, Deister tables, or water only cyclones. Growing interest in the Batac jig as a replacement for the above equipment is due to the following reasons: • Unlike heavy medium cyclones, no magnetite is required. As a result, the operating cost of the plant is reduced. • The compactness of equipment is unique on a unit ton per hour basis as compared to other equipment. • Solid state electronic control of jig stroke length, frequency, and jig bed depth makes the equipment highly efficient. Installations of Batac jigs in the US as of June 1980 are shown in [Table 1]. Use of the Batac jig is even greater outside the US (Anonymous, 1980; Chen, 1980). Its use is not limited to fine coal but is applied to coarse coal as well, with 102 mm size in the feed (Zimmerman, 1975). In countries where consumption of magnetite associated with the heavy medium system of coal cleaning is considered a waste of iron ore resource, the Batac jig is regarded as the primary choice in the selection of cleaning equipment (Chen, 1980).

Jan 1, 1981

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness and grindability of coal determine the maintenance cost for coal mining, handling, and pulverizing equipment; the specific gravity of coal and its associated minerals determines the coal preparation technique used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent on the chemical constituents of coal, and all properties are interrelated. Specific Gravity The specific gravity (sp gr) of a solid is the ratio of the weight of a cubic foot of the solid to the weight of a cubic foot of water. The specific gravity of pure coal has been reported to range between 1.23 to 1.72 and increases with the change in rank from lignite to anthracite. This means that it is 1.23 to 1.72 times heavier than water.

Jan 1, 1981

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By G. A. Wells

The consumption of barytes in certain paints, polyurethane foams, seamless flooring, glass, brake linings, plastisol gaskets for food containers, and in fluids used for gastrointestinal X-ray examinations relies on the unique properties of barium sulfate. There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase Prices which have encouraged the use of alternative or competitive materials and restricted market growth.

Jan 1, 1981

By K. W. Grubaugh, L. W. Saperstein

The recently enacted federal surface mine law (P. L. 95-87) increases further the complexity of securing a reclamation permit This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the construction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance, and improved cost control.

Jan 1, 1981

By James K. Grunig

As the real price of uranium increases, deposits of lower and lower grade will be treated. The various occurrences of uranium ore are described and the chemical aspects of extraction are detailed.

Jan 1, 1981

By K. Thirumalai, D. P. Schlick

Longwall Technology has a potential of resulting in safety and productivity improvements of U.S. underground coal mining similar to those experienced by the introduction of continuous miner systems. The study presents a comprehensive national evaluation of longwall technology to assess the potential of longwalls to improve health and safety and coal productivity. The study was conducted by the authors during the spring of 1980 as part of MSHA New Technology Coordination activities and with a view to examine the factors that may limit the acceptance of longwall technology in the U.S. coal mining operations. The study points out areas where adjustments need to be made in MSHA regulations and enforcement to help Longwalls. A two-entry longwall system appears to offer a practical method of improving underground coal productivity and safety. Applying regulations that are primarily designed for room and pillar methods to longwall mining, in some instances, reduces the effectiveness and productivity benefits feasible by new technology application. Controlling dust is the single predominant problem in the design and operation of longwalls in the United States. The results of this study points out a need for a coordinated program between government and industries on dust control technologies for examining acceptable technological options to control dust in longwalls without restraining the production capability of the system.

Jan 1, 1981

By F. P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in common rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modeled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1981

By R. Hogg, F. F. Aplan, P. B. Bradley

The mineralogy of the solids contained in the black-water effluent from coal preparation plants has been investigated. Samples were obtained from 13 locations, representing major coal seam in the Appalachian, mid-continent, and western regions of the United States. On the average, the samples were found to contain 60% carbonaceous material with the balance as mineral matter. The mineral fractions from all of the samples from the eastern half of the United States were found to be remarkably similar, consisting of over 50% illitic clays; about 10-15% each of kaolinite, calcite, and quartz; and lesser amounts of chlorite and pyrite. The western samples were somewhat different, generally containing significant quantities of montmorillonite clay. Flotation may be wed to recover additional clean coal contained in the black-water discharge.

Jan 1, 1981

By Warnie Flint

PERSONAL INJURY ACCIDENTS According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. NO one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, but not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

By Jack A. Simon, M. E. Hopkins

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981