Search Documents

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

Jan 1, 1947

By Alexander Squire

ONE of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test: methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials' and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three-chemical analysis, density, and hardness. The last of these may or may' not be a pertinent characteristic, since the indentation hardness of many powdered-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple, to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. , It. is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the properties of compacts formed from different types of powders are made on the basis of compacting... pressures instead of density, and for. this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By George D. Dub

INTRODUCTION OWENS LAKE is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.2H20) and borax, (Na2B407.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. CLOSED BASINS Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I Chloride type; largely sodium chloride (NaCI) and of oceanic type, such as Great Salt Lake. Related is the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. 2. Sulphate type; largely sodium sulphate (Na2S04) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate-chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate-Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1947

By Donald W. Scott, L. A. Roe, B. J. Sweo

INTRODUCTION THIS paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizers and organic dyes, and 35 parts of water are added to loo parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder' in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the overspray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1947

By Fred C. Bond

MANY grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.1 The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1 1/2 to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six 1 1/4-in. diameter and two 1 3/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5° for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus 1/2-in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication3 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1947

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By A. R. Oltrogge

WE have just seen? that resistance is a characteristic of an electric circuit that makes it difficult for current to flow; also, that if, by the application of voltage, we cause a current to flow through a circuit having resistance, heat is generated. This is the principle utilized in the production of heat by electric power in the arc furnace. In order to fully appreciate the problems of the arc-furnace electric circuit, let us examine the characteristics of some of the more commonly used materials that offer resistance to a flow of current and thereby produce heat. Usually the resistance material is a metal or a metal alloy, such as the nichrome ribbon in an electric toaster or the tungsten filament of an ordinary light bulb. These are the materials whose resistance-remains relatively fixed and which therefore permit the flow of a definite amount of current for a given impressed voltage. If we want more current to flow, we must either decrease the resistance or increase the voltage that is causing the current to flow. Such a resistive material has what we call a positive volt-ampere characteristic, which means that in order to get more current we must apply more voltage, and in order to reduce the current we must reduce the voltage. Such a volt-ampere characteristic can be represented by a line plotted on a graph (line B, Fig I).

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

By B. K. Miller, George E. Moore

THE Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the over burden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known clay deposit. A two-man crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot.

Jan 1, 1947

Jan 1, 1947

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By Charles Locke

IT will soon become apparent that the Conference Committee's choice of the title for this presentation is a fortunate one for the speaker; since if it had read "Review of Known Facts Controlling Slag Volume" he would best step down right now. There is a dearth of facts in a quantitative sense on this subject, especially in regard to the effects of slag volume on the acid electric practice for steelmaking, as borne out by a library search involving some 175 references from 1915 to date. Even the opinions in these references on any phase of slag volume are meager. This, then, leads to a report that is candidly based on private observations, on readings and on conjectures gleaned from gossiping with fellow practitioners. Perhaps the subsequent papers, which, as I understand it, are substantiated by actual measurements, of slag volume versus specific contributing factors, will be able to acclaim or disclaim my remarks.

Jan 1, 1947

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

Jan 1, 1947