Search Documents

By George Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable appara-tus, which can rapidly give a sufficiently reliable indication of the rela-tive dust hazard.

Jan 1, 1937

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By E. P. Haqyes, J. K. Butler

011, and gas development has continued unabated on the Texas Gulf Coast during 1937. Although the number of important new discoveries has not been great, the extensions in older fields, owing to discovery of new sands and the lateral extension of known sands, has been extensive. Twenty-four new producing fields were added during the year, and many of these areas give promise of developing into important producing districts in the future. Alta Mesa, Amelia, Aransas, Clara Driscoll, Five Corners, Hamman, Heyser, Old Ocean, Premont, Seabreeae, Segno and West Columbia have all had major extensions during 1937. The 1937 production for the Texas Gulf Coast was 120,141,429 bbl., or 32f per cent increase over the 1936 production of 90,865,293 bb1. t The total number of producing wells has increased from 6727 to 8968. Well abandonments have becn few and indications are that they will continue to be so. Rigid proration has been and continues to be in effect, and, as a result, wells in the Gulf Coast will have prolonged life. New Fields Tables 1 and 2 contain general information on all fields in this district. The following named fields were discovered in 1937: Aransas County.—Barnsdall Oil Company's No. 1-A Edwards was the discovery well for the Lamar field. It was drilled to a total depth of 9785 ft., plugged back and completed at 7530 ft. in the Frio as a gas and distillate well. Present indications are not very promising for a major field. Bee County.—The McMurray (Strauch) field was discovered by Dirks Bros. No. 1 Strauch at a total depth of 4577 ft. This is a Yegua producer, and had an initial production of 230 bbl. on a 3/16-in. choke. Brazoria County.—The Sandy Point field was discovered by Henry DeArmanls No. 1 Fite, which was completed as a producer at 6501 ft. in the Marginulina-Frio series. Galveston County.—Although the Hitchcock field was discovered in 1936, the first commercial oil producer was completed in 1937 when

Jan 1, 1938

By A. T. Miesch

The purpose of this paper is to explore relations between the distribution and composition of uranium deposits on the Colorado Plateau and mineralogic, chemical, and lithologic aspects of their host rocks. The paper also appraises the host-rock sandstones as possible sources of elements in the uranium deposits. Other possible sources of elements are not discussed. Uranium deposits on the Colorado Plateau consist largely of sandstone and small amounts of mud-stone impregnated with uranium and vanadium miner- als and a suite of minor accessory minerals containing copper, lead, zinc, silver, iron, cobalt, nickel, yttrium, molybdenum, selenium, and arsenic, in addition to other elements locally. The deposits consist of clusters of closely spaced ore bodies which commonly aggregate several thousand tons, but range in size from less than one ton to several million tons. With only rare exception, the deposits show no close relation to fractures. The ore bodies are generally tabular in layers nearly parallel to the bedding in the host rocks, or they cross bedding at large angles to form roll structures. Absence of fracture control necessitates that the ore and associated elements were transported to the deposits by way of interstitial pore spaces in the sandstones. This points to the general process of lateral secretion as a possible mechanism of ore formation, and suggests the host-rock sandstones as a possible source of the metals. Roll structures in the ore

Jan 1, 1962

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used. Together with 4 pct gypsum to retard setting time, the kiln run clinker—consisting of hard, semi-fused lumps that may have been crushed to — 1/2 in.—is ground to a Blaine surface area of 3000 sq cm per gram and about 92 pct passing 325 mesh. Approximately 32 kw-hr per ton, or 6 kw-hr per 376-1b barrel, are consumed in the grinding mills alone, not counting auxiliaries. Open Circuit Clinker Grinding: Many early clinker grinding plants employed two-stage, open circuit grinding. Comparatively short mills of large diameter, loaded with balls 4 in. and smaller, first reduced the clinker to 95 pct passing 14 mesh. Tube mills of smaller diameter and greater length, loaded with balls 11/4 in. and smaller, carried out the fine grinding operation. An early development was to assemble two or more stages of grinding in a single mill having two, three, or four compartments separated by division heads. There were difficulties in balancing the compartments, but compartment mills were popular in the 1920's because the layout was simple and there were no elevators and conveyors. Oversize Particles: Open circuit mills, whether separate ball and tube mills or compartment mills, always encountered the problem of tramp oversize in the product. A small percentage of clinker survived passage through the first grinding stage as particles—perhaps 1/16 in. diam—that were too large for the smaller balls in the following stages to reduce to —200 mesh. When the feed rate was lowered to reduce tramp oversize, there were serious losses in grinding efficiency. Many ingenious designs were perfected to incorporate perforated screen plates or wire mesh screens in the ball mills or in the first compartments of compartment mills. Their purpose was to prevent mate: rial passing out of the first stage until it was small

Jan 1, 1958

By Nicholas J. Grant, John Chipman

A FULL understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization; the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag-i.e., equilibrium conditions-and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck :20 [ ] Among others there appear the following:

Jan 1, 1946

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By Freeman Bishop

Copper production has been under Government scrutiny for many years because it's known as a concentrated industry which in turn creates what many economists label administrative prices. Neither of these conditions is illegitimate, per se, the Federal Trade Commission and the Justice Department have said time and again. But Justice spoke up once more. This time over a Puerto Rican copper development planned by American Metal Climax, Inc., and the Kennecott Copper Corp. Bureaucratic Dichotomy Creates Confusion and Conflict In the Copper Industry Ian MacGregor, chairman and chief executive officer of Amax, said Justice in a recent communique questioned the propriety of the proposal of a joint copper venture in Puerto Rico. At the same approximate time, Dr. Hendrik S. Houthakker, chairman of the President's Commission on Copper, was urging copper producers to expand production to help hold down prices by making more copper available to all consumers. This, Mr. MacGregor said, is creating confusion and conflict, since the Administration from one source is chastising the industry for doing what another branch requests.

Jan 1, 1970

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

This symposium is based on material presented at the AIME Annual Meeting in New York, February 1958. Co-Chairmen of the panel discussion were Truman H. Kuhn, Colorado School of Mines, and J. E. Monroe, Freeport Sulphur Co. Panel members are listed above. In opening the meeting Chairman Monroe pointed out that both industry and education have their special problems and that the purpose of this and similar discussion groups is to bring together members from both industry and education in order to help solve their problems.

Jan 6, 1958

By R. F. Shurtz

The author proposes a method used with some success on a magnesite deposit at Gabbs, Nev. He believes this procedure to be more sound than the blind practice of assigning uniform quality to large, soinetimes vast blocks or ore on the basis of analyses made of a small number of samples. When an ore deposit is evaluated on the basis of core sampling, questions always arise as to how much weight should be given the various sample grades and how the deposit should be divided into specific volumes assigned to corresponding grades. For a tabular deposit it is customary to use the so-called zone-of-influence. This zone is usually defined as the polygon in the plane of the deposit having corners halfway between a given core drill intersection and each of the nearest neighboring intersections. The volume of the ore in this polygon is assigned the analysis obtained from the drill core taken at the intersection. In massive or irregular deposits, volumes of various shapes may be defined with respect to the locations of drill core samples. These volumes may be regarded as three-dimensional zones-of-influence; the theory involved in assigning the values of the central analyses to the ore in the volumes is the same as that used in the case of a tabular deposit. The zone-of-influence method was used in evaluating one of the magnesite deposits at Gabbs, Nev.'-"

Jan 1, 1960

COLORADO LOCAL SECTION Executive Committee CHARLES A. CHASE, Chairman S. A. IONIDES, Vice-Chairman C. LORIMER COLBURN, Secretary-Treasure, 614 Ideal Bldg., Denver, Colo. F. H. BOSTWICK, W. G. SWART. The annual meeting of the Colorado Local Section of the Institute was held at the Savoy Hotel, Denver, Jan. 15.- The Chairman, Frank Bulkley, presided and made a short address on the work of the Section. The following officers were elected:

Jan 3, 1915

Jan 1, 1950

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called' "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also.

Jan 1, 1928

By C. P. Parsons

To properly account for the various characteristics of drilling muds obtained in different areas and geological horizons, it is necessary to study the composition of the mud from a chemical and physical standpoint as determined by the proportions and activities of the various solid contituents that are present in various states of division. Briefly summarized, science teaches that there are three states of division into which these solid constituents or particles may be grouped: namely, the suspended state, the individual particles of which are known as suspensoids; the colloidal state, in which the individual particles are termed colloids; and the crystalloidal state, wherein the individual particles are held in true solution and are termed crystalloids. The suspended state is one wherein the particles are fairly large and are present as molecular complexes, having none of the properties of colloids or crystalloids. Since matter varies in physical character and in chemical activities with its state of division, these coarser suspensoids do not themselves materially affect the physical or chemical properties of the solution in which they are suspended. On the other hand, they are distinctly detrimental in drilling muds and it is desirable that they be removed. Under the general classification of suspensoids are included sand, gravel and cuttings which contribute nothing to the colloidal stability or other desirable properties of the drilling fluid. As the state of division approaches but does not reach a molecular simplification, the term "colloidal state" is used in describing this condition. The colloidal state arises when one form of matter is in a very fine state of division and is distributed through a second phase. The material in the finely divided state is called the dispersed phase, while the liquid in which it is dispersed is called the dispersive phase. These particles of matter are in a colloidal state and will not settle out from the dispersive phase so long as colloidal conditions are stable. Moreover, they exhibit the property of having an oscillating movement around a central position in solution (the Brownian movement). In the third state of division, the crystalloidal state, the individual particles are held in true solution and are usually present as single molecules or ions. In a drilling fluid the water content of the fluid contains

Jan 1, 1931

By Glenn Allen

SAN FRANCISCO Mines of Mexico, Ltd. owns and operates an extensive group of claims in the San Francisco del Oro-Santa Barbara district, about 15 miles southwest of Parral, Chihuahua. The property comprises the mines, aerial tramways, flotation mill, power plant, shops, offices, assay and testing laboratories, modern hospital, water and sanitary system, quarters for miners, mechanics and operators, a well housed colony for Mexican staff employees and residences for foreigners. Each colony has a club house and mess and tennis courts. The employees have constructed a nine-hole golf course. In other words, the property is self-contained and completely integrated for production of lead and zinc concentrates from complex sulfide ores.

Jan 1, 1930

By J. H. Hamilton, J. R. Lewis, J. H. Dismant, W. M. Fassell

RECENTLY this laboratory undertook the task of preparing some low carbon metallic cobalt by the carbon reduction of precipitated cobalt oxides. The oxides came in two lots and had the compositions given in Table I. Industrially, cobalt rondels' are made by the carbon reduction of cobalt oxide in small reverberatory furnaces at temperatures near but not above 1050 °C. This is a slow and tedious small batch process but does give cobalt metal which is low in carbon (1 pct C). Inasmuch as these cobalt oxides were relatively low in copper and iron it was decided to reduce them with petroleum carbon in a small three-phase electric arc furnace of about 3 to 5 Ib of metal capacity. It was hoped such a procedure would save considerable time and perhaps also indicate an improved commercially feasible process. The furnace was preheated by using small pieces of carbon electrodes to maintain the arc until a temperature of 1500°C was reached. The broken pieces of electrodes were then removed and 500 g of the cobalt oxides and 60 to 100 g of petroleum coke added. At the end of the reduction reaction, a high lime flux was added to the furnace to facilitate the removal of sulphur. Due to the fineness of the cobalt oxide powder used and also to the presence of chlorides there was considerable dust lost in charging the furnace. This was overcome by preparing briquettes composed of the cobalt oxides, charcoal, and a little bentonite to serve as a binder. The results obtained are summarized in Table 11, which shows that the cobalt metal produced in the arc furnace was high in carbon varying from 2.5 to 3.5 pct. This, of course, is much too high. For certain uses, such as in the preparation of permanent magnets, the carbon content of cobalt must be low. It was necessary therefore to find an effective method of reducing the carbon content of the cobalt that had been prepared in the arc furnace. Van Arkel3 recommends the use of Co2O3 as a means of removing carbon from cobalt. Experiments by the authors indicate that carbon is removed with difficulty by this method. Other methods used, including lancing of the molten high carbon cobalt with a jet of oxygen, proved to be ineffective. The method finally used makes use of the fact that cobalt metal is decarburized by carbon dioxide at the temperature of the molten metal. Two methods were used: 1—carbon dioxide was bubbled up through the molten cobalt, and 2— molten cobalt was maintained in a carbon dioxide atmosphere. In the first method the gas was introduced below the surface of the molten metal by means of a quartz tube. A high frequency induction furnace was used to keep the cobalt molten in both of these experiments. This kept the metal somewhat agitated and no doubt was an important factor in hastening the decarburization 'process by the second method. Both methods gave satisfactory results as shown in Table 111. An interesting observation in connection with this 'work was that a small sample of carburized cobalt metal could be decarburized by heating it with an acetylene torch adjusted to give an oxidizing flame. This may have been due to the presence of carbon dioxide in the products of combustion. Samples of molten high carbon steel were decarburized by the same method and it is suggested that nickel and perhaps manganese can be decarburized in a similar manner. Additional work, including rate studies and other theoretical aspects of this problem, is in progress in this laboratory.

Jan 1, 1953

By D. G. Deveraux

A BRIEF SKETCH OF THE DAVE JOHNSTON MINE The Dave Johnston coal mine is located near the southwestern extremity of the Powder River Basin in central Wyoming. This mine is operated entirely for the purpose of furnishing fuel to the 750,000 Kw Dave Johnston power generation station located five miles east of Glenrock, Wyoming on the North Platte River about 24 miles east of Casper, Wyoming. Coal is delivered to the power plant by a company-owned railroad moving the coal 15 miles downgrade from the mine to the power plant. The mine first belonging to Pacific Power & Light Company has now been transferred to Northern Energy Resources Company (NERCO), a mining subsidiary of Pacific Power & Light Company. The coal beds which make up the field at the Dave Johnston Mine are locally referred to as the School and Badger seams and occur beneath gently rolling terrain in the Fort Union formation. The School seam is found approximately 180 feet beneath the Badger in the southern portion of the field and about 110 feet beneath the Badger towards the north. The coal beds dip down toward the northeast on about a four percent average inclination. The School seam has an average thickness of about 35 feet and the Badger seam about 16 feet. The climate at the Dave Johnston Mine is semi-arid, with annual precipitation varying between 10 and 12 inches with 70 percent occurring during the months of April to September, with the maximum occurring in May. A few storms occur in July and August which are usually torrential in character, often causing erosion damage to un- protected soils. Snowfall averages 50 inches a year at the mine with 12 to 15 inches of snow yielding one inch of moisture. However, snow seldom

Jan 1, 1983

By F. V. Lenel, M. V. Rose, A. B. Backensto

WHEN aluminum-flake powders are compacted and hot pressed and the resulting compacts are extruded or hot forged, a group of materials with unique properties is obtained. Not only do they exhibit high room-temperature strength of the order of some of the aluminum alloys, but they maintain this strength even after prolonged heat treatment at temperatures up to 900°F. Moreover, their strength decreases much less with increasing temperature than that of aluminum alloys of comparable room-temperature properties. Irmann,'" who discovered and first described this group of materials, which was called SAP, showed that the room-temperature mechanical properties of the extrusions are a function of the oxide content of the powders and therefore the oxide content of the extrusions. The higher the oxide content, the higher are their tensile strength, yield strength, and hardness, and the lower their ductility. Lyle" investigated the relationship between mechanical properties at elevated temperature and oxide content in the course of the development work of the Aluminum Co. of America on materials, called APMP, similar to those developed in Switzerland. He found that at 600 °F, just as at room temperatures, tensile strength and yield strength increase and elongation decreases with oxide content. A careful study of his data (Fig. 3, loc. cit.) shows, however, that the scatter is more pronounced than at room temperature. Gregory and Grant's data on the creep5 and stress-ruptureb roperties of the one commercial grade of the Swiss SAP and the various grades of APMP indicate that creep strength and stress to rupture also generally increase with increasing oxide .content. Ever since this new group of materials was discovered, attempts have been made to explain the mechanism by which they obtain their high room-temperature and particularly their elevated-temperature strength. In most of the attempts the new material was considered as a dispersion of aluminum oxide particles in a matrix of aluminum. Ir-mann, Von Zeerleder, and Rohner' applied a theory on dispersion strengthening developed by Rohners to the flake-powder extrusions. According to this theory the elastic limit S, of a dispersion would depend upon the average distance between the dispersed particles L according to the equation: 2 E ¦ a where E is the modulus of elasticity and a the distance between nearest neighbors in the lattice of the matrix material. Irmann and co-workers assumed

Jan 1, 1958