Search Documents

By R. E. Carter, F. D. Richardson

Self-diffusion coefficients have been measured for iron in wustite (700° to 1000°C) and for cobalt in cobaltous oxide (800&apos; to 1350°C) by means of radio-isotopes. Both sectioning and decrease of surface-activity methods have been used and a particular shortcoming of the latter method has been disclosed for wustite. The effects of oxygen pressure on the composition of cobaltous oxide and on the diffusion coefficient of cobalt in the oxide have been established. The effect of the preparation conditions of the cobalt-oxide specimens on the diffusion measurements has been determined. It has been concluded that diffusion of cobalt occurs via vacant cation sites and that a cobaltous-oxide disk reaches equilibrium with its environment in a time which is very short compared with that needed for diffusion of the radio-isotope. THE availability of radioactive isotopes in recent years has permitted the measurement of many self-diffusion coefficients which were hitherto impossible to determine. With the advent of radioactivity, the method of measuring diffusion coefficients has also changed. The earlier sectioning method by which the concentration profile of the diffusing species was determined in the diffusion specimen has often been rejected in favor of the decrease of surface-activity method first developed by Von Hevesy,&apos; and extended by Steigman, Shockley, and Nix,&apos; and Raynor, Thomassen, and Rouse." With the experimental arrangement where an infinitely thin deposit of tracer is diffused into a semi-infinite cylinder, the decrease in activity of the active face due to diffusion of the tracer into the specimen is measured by counting the active face before and after diffusion. Under these conditions, the appropriate solution of the diffusion equation is R = e*(l-<K/Z) [1] where R is the ratio of the counting rates after-to-before diffusion, $& is the Gaussian error integral of \/Z, and Z is defined as Z = p2Dt, p being the linear-absorption coefficient of the detected radiation in the diffusion specimen, D the self-diffusion coefficient, and t the diffusion time. In the older sectioning method the concentration distribution of the tracer is found after diffusion by analysing thin parallel sections cut from the active face of the diffusion specimen. As seen from the solution of Fick&apos;s second law for the distribution of an infinitely thin source after diffusion into a semi-infinite cylinder the log of the concentration plotted against x&apos; will be a straight line of slope log e/4 Dt. The diffusion coefficient thus can be calculated directly. The units of the tracer concentration are completely arbitrary, since any change in units does not change the slope of the log c vs x2 lot. Although both of the above methods have been widely used, a thorough experimental comparison does not appear to have been made. Birchenall and Mehl,&apos; during an investigation of the self-diffusion rate of a and r iron by the surface method using Fe" tracer, diffused and sectioned one welded couple. The diffusion coefficient from this run agreed with those by the surface method. Buffington, Bakalar, and Cohen," during an investigation on a and y iron

Jan 1, 1955

By H. L. Hopkins, L. W. Kempf

Aluminum alloys, in common with most other metallic alloys exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with temperature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative consideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators &apos;-5t have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys Subcommittee, during 1917 and 1918, which are not generally available in published form. In these reports the term "permanent growth" was applied to the dimensional changes occurring in the pistons at the tem-

Jan 1, 1936

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.&apos;&apos; The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

United Engineering Society J VIPOND DAVIES,-President WILLIAM L SAUNDERS ALFRED D FLINN Secretary GEORGE H PEGRAM, 2d Vice-president JOSEPH STRUIHERS, Treasurer HENRY A LARDNER Assistant treasurer Finance Committee House Committee WILLIAM L SAUNDERS, Chairman ALFRED D FLINN, Chairman GEORGE H PEGRAMO FREDERICK F SHARPLESS ARTHUR S DWIGHT JOHN H DUNLAP BANCROFT GHERARDI CALVIN W RICE I VIPOND DAVIES, ex-officio F L HUTCHINSON

Jan 1, 1923

State Geological Survey of Kansas, Lawrence, Kansas Raymond C Moore, State Geologist. A list of publications will be sent upon request Most of the earlier volumes and bulletins of the Survey are now out of print, and available only at libraries Many of the bulletins

Jan 1, 1933

By C. K. Leith

QUOTING from Dr. Richard T. Ely:1 "Conservation, narrowly and strictly considered, means the preservation in unimpaired efficiency of the resources of the earth; or in a condition so nearly unimpaired as the nature of the case, or Wise exhaustion, admits. And broadly considered, it means more than the word itself implies, for it naturally includes an examination of methods Whereby the natural inheritance of the human race may be improved; and still more broadly considered, and as used in popular discussion, it includes a treatment of the effects of productive conservation methods upon distribution. "Conservation means a sacrifice of the present generation to the future generations Whenever it is carried too far. There is a sharp limit to the economic sacrifice that we may reasonably ask the private person to make for even the present Welfare, and the limit is still sharper when we come to consider the interests of future generations." In a paper on the iron ores of America, presented to the Pan-American Scientific Congress at Washington, I have emphasized the fact that the reserves of iron ores in the two Americas are enormously in excess of the requirements of the present generation, in fact, so large that no shortage is to be anticipated for many generations in the future; that a large part of the value of iron ores is put into them by man&apos;s efforts to make them available. This fact is fundamental for the intelligent consideration of- policies of conservation as applied to iron ore. As I interpret it, this fact makes it practically unnecessary that the present generation should make any especial sacrifice for future generations in the way of conservation of its iron-ore resources. Even if we were disposed to look forward to a period of 100 or 200 years, with a view to insuring the welfare of the people living at that time, it is doubtful whether any procedure we could now formulate would materially help them in the matter of iron ores, so large are the reserves available. In order that an appeal for conservation may be effective it must obviously favor the welfare of the present or immediately following generations; it must promise benefits to general and individual welfare during a period within the range of comprehension of the average man.

Jan 2, 1916

By A. Bruce Matthews

Of the many opportunities in the mining industry to invest funds to improve operations, there is always some limit in every company as to how much can be spent each year for the acquisition of capital assets. Generally, there are many more opportunities for investment than funds to make the investments. As such, one of management&apos;s goals is to select the most profitable of all the opportunities available. Each opportunity must be carefully analyzed for its potential percentage rate of return. This percentage return or return on investment concept is an accepted financial yardstick of business profit- ability. For today&apos;s mining engineers, this problem resolves itself in the job of determining how to in- vest most productively the cash that is flowing from their operations so that it will multiply in value. There are four basic types of capital investments: Strategic investments, such as selecting a plant site, are those that affect virtually all long-run plans of a company. Change in a company&apos;s product line and expansion of company facilities are two other types of capital investments.

Jan 3, 1963

By F. W. Jessen

The Mechanism of solution of salt and mixed halites of sodium and potassium is reviewed. The variation in the rate of salt removal under both laminar and turbulent flow conditions is discussed. Many changes are possible in the development of solution cavities whether used for production of salts or for storage of hydrocarbons. The parameters influencing the type and shape of cavity formed with single well or multiple well systems are examined and information presented regarding field application of techniques developed and the means of controlling overall configuration of solution cavities.

Jan 1, 1972

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

Jan 1, 1902

By G. P. Gladis, R. H. Atkinson

PALLADIUM has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items-at least 100 times as rare as gold. Although both visual and spectrophotometric examination demonstrated that the color of palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400° to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By Emil Gathmann

Through wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot. Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium, there is no commercial reason why all steel should not be thoroughly degasified. A degasified steel being provided, the method of freezing or solidifying the liquid steel into an ingot, and the subsequent working into blooms and thence into various products, is of great importance in reducing the crop or scrap portion of the steel, due to segregation and pipe. How to ac-

Jan 1, 1916

By Paul D. Merica, O. B. J. Fraser

PROBABLY the first metallic objects used by man were nickel alloys. In search for flints suitable for the fashioning of their rude tools, our paleolithic ancestors, some 25,000 years ago, quite likely may have come upon some of those heavy, metallic fragments that we now know as meteorites, which consist of an alloy of nickel and iron containing usually from 5 to 15 pct of nickel. Whether paleolithic man ever did discover and use meteoritic fragments, his sketchy records do not actually disclose. We do know, however, that such fragments have been found and used by peoples, particularly the North American Eskimos, for weapons and implements in just the same manner as stones, and prior to any knowledge by those peoples of the reduction of metals from ores. Meteoritic showers were recorded frequently in earliest times and the meteorites often were found and fashioned into useful objects. The ancient Arabic and other myths of "invincible swords fallen from heaven" seem thus to have had a very definite basis in fact, and such weapons, of meteoritic material, have actually been re- covered from archeological excavations. It thus seems probable that meteoric nickel-iron was found and used long before iron was recovered by smelting iron ores (perhaps about 1200 B.C.) and probably even before there was knowledge and use of bronze and gold. Although many centuries were to pass before nickel was first isolated, in 1751, from Swedish ores and recognized as an elemental

Jan 1, 1953

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman. JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 9, 1913

By James P. Kimball

Jan 1, 1881

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours&apos; duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.&apos; This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.&apos; Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool&apos; which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By C. S. Matthews, P. Hazebroek, H. Rainbow

It ha been suggested that lormation fractures created by well stimulation treatments will adversely affect sweep-out efficrency in injection operations. Fluid-flow model studies involving vertical fractures of various lengths and fluid systems of various mobility ratios have been carried out to study this subject. In addition, limited data have been obtained on one model containing a horizontal fracture. It was found that relatively long and highly conductive fractures (not generally obtained fracturing operations) were required to affect the sweep-out efficiency substantially. In a given case in the field an approximate distinction can be made between the presence of long conductive fractures and shorter or less conductive ones. This is done with pressure build-up analyses along with data on the relationship of fracture length and conductivity to well productivity. This type analysis shows that usually the fractures induced are either short or of limited conductivity and therefore do not damage sweep-out efficiency. INTRODUCTION Improved well productivity and in-jectivity can frequently be exploited in injection operations. Higher total throughput can yield improved economics. On occasion, the achievement of an increased productivity or injectivity in specific wells can bring about a more uniform sweep of the reservoir. Higher rates can be exploited particularly in water floods of "depleted" reservoirs where a rapid "fill-up" is desired and where low pressures contribute to low well productivity. The creation of fractures local to the wellbore is an excellent means for achieving these objectives. Even though fracturing has been employed in some floods with success,1"3 there still seems to be some reluctance to employ this tool for fear of undue damage to the flood pattern and ultimate recovery. We therefore need to examine the influence which fractures of varying length may have on flood performance and then determine the length of fractures which obtain in the field with conventional fracture treatments. A substantial influence of fractures on the recovery obtained at breakthrough of the injected fluid has been presented by Crawford and Collins for equal fluid mobilities for the line-drive pattern.4,5 In addition, the influence which a fracture has on the production performance after breakthrough and on the ultimate recovery warrants consideration in reaching a conclusion concerning the use of induced fractures in flooding operations. This report presents this type of data for the five-spot injection pattern for several fluid mobilities. In arriving at some conclusion concerning the fracture lengths obtained in field operations we must examine the performance characteristic most affected by the fracture. This is the change in the flow system as reflected in the change in productivity and pressure build-up behavior. A study of these changes is also presented in this report. RESERVOIR ANALOGS The X-ray shadowgraph technique, employing miscible displacement in porous models, has been used in the study of the influence of fractures on pattern sweep-out efficiency. The X-ray shadowgraph procedure is described in detail in an earlier report8. Fractures were represented by leaving the proper portion of the model surface exposed to either injection or production. This assumes the fracture resistance to be negligible compared to that of the formation. Actually the flow resistance in propped fractures obtained in the field is sometimes not negligible so that the results with this model indicate the maximum influence of the fracture. Two types of models were necessary to represent vertical fractures in a five-spot flood. These pattern elements are illustrated in Fig. 1. In studying the influence of the horizontal fracture, only one well spacing length to thickness ratio of 50 was used. The pool unit of a Carter Electric Analyzer was used in studying the influence of fractures on productivity and build-up behavior. The square drainage system of a well was represented by a network of 576 elements of equal volume and resistance. One-fourth of this drainage area was studied as a model unit using a network of 144 condensers and resistors. Vertical fractures were represented by a shunt directed from the well perpendicular to the drainage boundary. Horizontal fractures were represented by a circular shunt. Resistance of a shunt was varied in representing different conductivities for the fractures. FRACTURE DIRECTION AND LENGTH The direction at which a vertical fracture extends into the formation and its length and conductivity influence the sweep behavior. The two