Search Documents

THE shipments of high-grade manganese ore, con-taining 35 per cent or more of manganese, from the mines in the United States in 1926 were slightly less than half as large as similar shipments in 1925, accord-ing to the United States Bureau of Mines, Department of Commerce. The shipments in 1926 by 45 producers amounted to 46,258 long tons as compared with 98,324 long tons by 42 producers in 1925. This decrease was due to the falling off of the shipments from Montana. The domestic production of metallurgical ore in 1926 was 26,530 tons; that of chemical ore, 19,728 tons. Montana was the largest shipper with 5713 tons of metallurgical ore and 17,904 tons of chemical ore. The largest individual shipper of metallurgical ore was the Crescent Mine in the Olympic Mountain Region, Clallam Co., Washington, from which the shipments for the year were 3162 tons. The mine was operated by lessees and reverted to the owners in July, and thereafter to the close of the year no .ore was shipped.

Jan 6, 1927

Jan 1, 1913

By Donald A. Dahlstrom

The selection and sizing of filters depends on the characteristics of the type of filter and the feed slurry. In addition, the rate functions of cake formation, cake washing and cake dewatering must be determined in order to design the filter station on the basis of desired performance. This chapter discusses the applied theory used to determine the rate functions and illustrates how to incorporate these into the filter cycle to obtain the required objectives. This also permits the sizing of the filter and auxiliaries as well as the selection of the proper type of filter.

Jan 1, 1978

By Stanley B. Roboff

Throughout the world nuclear power re- actors are being designed and constructed as the energy source for stationary power plants. They are built to power submarines, surface ships, and long-range aircraft and to provide small package power plants that can be set up with relative ease in outlying areas. Regardless of type, most of these plants are designed to operate at the highest permissible temperatures and with the greatest possible burn-up of fuel. On paper it is now possible to design a nuclear power plant that will out-perform all existing types of power-generating plants, and at costs which are attractive. Such plants, however, are not now being built, nor will they ever be built, unless major engineering advances are made in the realm of reactor materials. The reason for this is straight- forward enough. Although it is known that huge quantities of energy can be generated in nuclear fuels within short periods of time, as yet there are no construction materials capable of withstanding the severe conditions that would exist within a power reactor operating with ultrahigh output.

Sep 1, 1956

By M. Metzger, J. C. Bilello

Microyielding in 99.999 pct Cu occuwed in two distinct parabolic microstages and was substantially indeoendent of grain size at the relatiz~ely large grain sizes stzcdied. The strain recouered on unloading was a significant fraction of the forward strain and was initially higher in a copper-coated single crystal than in poly crystals. Results were interpreted in terms of cooperative yielding and short-range dislocation motion activated otter a range of stresses, and a formalism was given for the first microstage. It was suggested that models involving long-range dislocation motion are more appropriate for impure or alloyed fcc metals. THERE are still many unanswered questions concerning the degree and origin of the grain size dependence of plastic properties. In the microstrain region, a theory of the stress-strain curve proposed by Brown and Lukens,' based on an exhaustion hardening model in which the grain boundaries limit the amount of slip per source, accounted for the variation with grain size of microyielding in iron, zinc, and copper.' This theory assumes N dislocation sources per unit volume whose activation stress varies only with grain orientation. Dislocations pile-up against grain boundaries until the back stress deactivates the source, which leads to a relationship between the axial stress and the strain in the microstrain region given by: where G is the shear modulus, D the grain diameter, a the flow stress, and a, is the stress required to activate a source in the most favorably oriented grain.3 If this or other grain-boundary pile-up models are correct, then the reverse strain on unloading would be much larger for a polycrystalline specimen than for a single crystal. Also, the microplasticity would become insensitive to grain size if this could be made larger than the mean dislocation glide path for a single crystal in the microregion. These questions are examined in the present work on polycrys-talline copper and a single crystal coated to provide a synthetic polycrystal. EXPERIMENTAL PROCEDURE Tensile specimens 3 mm sq were prepared from 99.999 pct Cu after a sequence of rolling and vacuum annealing treatments similar to those recommended by Cook and Richards4-6 to minimize preferred orientation. Grain size variation from 0.05 to 0.38 mm was obtained by a final anneal at temperatures from 310" to 700°C. Dislocation etching7 revealed pits on those few grains within 3 deg of (111). For all grain sizes dislocation densities could be estimated as -107 cm per cu cm with no prominent subboundaries. The single crystals, of the same cross section, were grown by the Bridgman technique with axes 8 deg from [Oll] and one face 2 deg from (111). An anneal at 1050°C produced dislocation densities of 2 x 106 cm per cu cm and subboundaries -1 mm apart in these single crystals. A Pb-Sn-Ag creep resistant solder was used to mount the specimens, with a 19 mm effective gage length, into aligned sleeve grips fitted to receive the strain gages. All specimens were chemically polished and rinsed8 to remove surface films just prior to testing. The synthetic polycrystal was made by electroplating a single crystal with 1 µ of polycrystalline copper from a cyanide bath. Mechanical testing was carried out on an Instron machine using two matched LVDT tranducers to measure specimen displacement, the temperature and the measuring circuit being sufficiently stable to yield a strain sensitivity of 5 x 107. At the crosshead speeds employed, plastic strain rates were, above strains of 10¯4, about 10¯5 per sec for polycrystalline specimens and 10-4 per sec for the single crystals. Plastic strain rates were an order of magnitude lower at strains near l0- '. A few checks at strain rates tenfold higher were made for reassurance that the initial yielding of polycrystalline copper was not strongly strain-rate dependent. Test procedures followed the general framework outlined by Roberts and Brown.9,10 An alignment preload of 8 g per sq mm for polycrystals, and 2 to 4 g per sq mm for single crystals, was used for all tests. These gave no detectable permanent strain within the sensitivity of the present experiments; although at these stress levels, small permanent strains are detectable in copper with methods of higher sensitivity.11 12 stress and strain data are reported in terms of axial components. RESULTS General. The initial yielding is shown in the stress vs strain data of Fig. 1. For polycrystals, cycle lc, the loading line bent over gradually without a well-defined proportional limit, and almost all of the plastic prestrain appeared as permanent strain at the end of the cycle. The unloading curve was accurately linear over most of its length with a distinct break indicating the onset of a significant nonelastic reverse strain at the stress o u, indicated by the arrows. The yielding in subsequent cycles, Id and le, had the same general character. The single crystal behavior, shown to a different scale at the right of Fig. 1, was different in that initially the nonlinear reverse strain was unexpectedly much greater than for polycrystals. It should be noted that these soft crystals had a small elastic

Jan 1, 1970

By M. L. Jeremic

Abstract-Observations of ground behavior in mining the Choka Dulkan ore body have been described. Ore recovery was limited to approximately 60% because unconsolidated hydraulic fill did not permit either the widening of stope spans nor secondary ore recovery from pillars. Stope undercutting induced high stress concentrations. However, as extraction progressed, ground conditions improved but before extraction was complete they deteriorated again. After completion of a stope, the remnant rib and crown pillars continued to be deformed by other stresses for some time.

Jan 4, 1978

By W. F. Burns

(Butte Meeting, August, 1913.) ATTEMPTS were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting- the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No.1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles.

Jan 7, 1913

By M. P. Sidorova, D. A. Fridrikhsherg

The surface charge, electrokinetic potential and surface conductance were studied for silica, alumina and rutile as the functions of PH and concentration of 1-1 electrolyte solutions. The adsorption potentials of potential-determining and specifically adsorbed ions were calculated from isoelectric and zero charge points on the basis of Stern equation and thermodynamic description. From surface conductance and charge data the mean ionic mobilities in double layer were estimated. The results give some information about the real structure of oxide-electrolyte interface and gel-layer concept.

Jan 1, 1980

By C. A. Heiland

THERE once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indica-tions, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophys-ical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much con-vinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family . he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's foot-steps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1938

By W. H. Reck

Increasing use of flotation in modern beneficiation has resulted in a variety of froth handling methods. Froth must be handled mechanically to maintain common floor elevation, because pure gravity flow, stage to stage, makes for multiple level machine installations with higher first cost and less convenient operation. Bucket Elevator--Froth is collected by launder and goes to the feed entry of the elevator, below the floor. The bucket goes to the next treatment stage by gravity flow. The outstanding advantage is high efficiency of conveyance.

Jan 5, 1955

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By C. J. P. Ball

Prior to 1939 the bulk of the magnesium metal produced outside of the united Stater was extracted directly from the ore and ifi the United States from magnesium chloride obtained as a by-product from the treatment of natural brines. A typical brine is one containing about 0.25 to 0.75 per cent bromine, 11 to 14 per cent sodium chloride, 9 to 11 per cent calcium chloride and 3 to 10 per cent magnesium chloride. The state of Nevada was known to possess large deposits of magnesite ore (MgCOs, the carbonate of magnesium), in Gabbs Valley, near Luning, approximately 350 miles north of Boulder Dam. Deposits mined in Europe were supplying magnesite giving 97 per cent MgCOs with about I per cent each of silica, lime and oxides of iron and aluminum. parts of the Luning de-posits Were almost equally rich, and the general average was of sufficiently high grade for production of magnesium. power to the amount of 200,000 kw. was available immediately from Boulder Dam, and water from Lake Mead, and it was this combination of available power, water, and ore that led to the initial proposal to erect a magnesium reduction plant in southern Nevada to reduce the magnesite ores from Gabbs. The extraction of magnesium metal from these magnesite deposits had been considered by the I. G. Farbenindustrie of Germany as far back as 1929. Mine and Oxide Plant The mine and oxide plant of Basic Magnesium Incorporated are perched upon the oride slope of the Paradise Range, at an altitude of 5000 ft., overlooking the 30 mile desert panorama of Gabbs Valley, Nevada. , Ore Occurrence The Gabbs magnesite ores occur in a thick series of flat, westerly dipping dolomites of Upper Triassic age. The mag-"esite bodies are exposed in steep canyon "areas encircling the north and east edges of a northerly projecting tongue of a roughly elliptical stock of granodiorite, which intrudes the dolomite. The magnesite mineralization is considered to be a a of calcium by magnesium through the agency of hydro-thermal solutions associated with the intrusion of the granodiorite. The ore bodies are of very irregular shape and distribution. Incomplete evidence points to deep pipelike replacement shapes that mushroom out erratically at various elevations. A wide latitude in the degree of magnesium replacement is reflected in a variance of quality from pure magnesite to magnesitic dolomite. The, ore is a massive crystalline mag-nesite. Though some differences in characteristics occur between ore bodies, in general the ore is a medium-grained carbonate varying in color from white, through all shades of gray, to black. Recrystallized dolomite, which encloses and occurs as

Jan 1, 1944

By Spencer Cragoe

I have read with much interest the elaborate and able paper of Messrs. Granger and Treville on the Mining Districts of Colombia, presented at the Atlantic City Meeting (ante, p. 33). Going into detail, however, as the paper does—and particularly with reference to the department of Antioquia, I am somewhat surprised that the property of the Frontino and Bolivia Company, probably one of the richest and most extensive in Colombia, should come off with such scant notice. The entire property embraces an area of some 28 square miles, and is situated at a distance of about 2 leagues from Remedios—after Medellin probably the most important town of the Department—and lying in approximately '7° N. latitude. The neighborhood of Remedios has been long celebrated for its production of the precious metal. Alluvial gold in large quantities has been obtained from the vicinity for upwards of two centuries; and even to-day a large proportion of the population finds a comfortable livelihood, during the dry season, in washing the sands of various rivers, notably the Rio Porce; while the amount of gold, in the form of nuggets, brought almost daily to Remedios and other points, from streams in the immediate neighborhood, is astonishing. These nuggets vary much in size. The majority, of course, are small, but larger ones are by no means scarce. I have been considerably surprised at the amount and value of the trade thus transacted between natives and merchants of the various towns. The property owned by the Frontino and Bolivia Company has been, I believe, for the larger part of the present century,

Jan 1, 1899

By Thomas MacFarlane

IN smelting copper, lead, and silver ores, it is scarcely possible in every case to make analyses of the various parcels of ore, with the view of combining these and the fluxes so accurately as to yield, in the furnace, slags of exactly the most favorable composition. This is even more difficult with ores which require previous calcination, or with mattes which have been roasted in heaps. Even in cases where the greatest pains have been taken and the most elaborate calculations made beforehand, it frequently happens that variations in the working of the furnace interfere with the result so much desired. Generally, the practical metallurgist must be content with ascertaining the average composition of his ores and fluxes, making a calculation once for all as to the most advantageous mixture, and leaving slight changes in its composition to be taken care of as it is passing through the furnace. The various products then afford him the best material whereon to base his judgment as to the manner in which his smelting mixture is working. Of course the character of the slag is one of his chief guides, but it is not always possible from its outward characters alone to form a correct judgment as to its composition. Neither would it be possible or practicable to apply chemical analysis for this purpose, as it would be impossible to wait for its results while working a furnace. Abich was, I believe, the first to point out the relation existing between the composition of volcanic rocks and their densities, and to show that, the latter being ascertained, very correct conclusions

Jan 1, 1880

By Richard D. Call

Data obtained from development drilling provide the basic input for open pit mine planning and design. Development drilling is defined as delineation of the size, mineral content, and disposition of an ore body by drilling boreholes (Thrush, 1968). The objectives of development drilling are: ( 1 ) determining the geometry of the mineralization, ( 2 ) determining the grade and tonnage, , ( 3 ) obtaining samples for metallurgical testing, and ( 4 ) obtaining geotechnical data for mine design. To accomplish these objectives, an appropriate drilling plan must include the number of holes, the spacing and orientation of the holes, and a suitable data collection program. The data collection program covers sample collection, hole logging, and data presentation. This chapter will present some guidelines for development drilling and data collection techniques. The operational aspects of drilling will be covered in an- other chapter.

Jan 1, 1979

By K. Koneko, T. Nokoyama, S. Shibato

SEYBOLT et al.' have detected various silica films formed on a 3 pct Si-Fe alloy after heating at low oxygen potentials with the electron diffraction method, and they have made some observations on the H,0/H2 ratios required to form them. The purpose of this note is to describe the structure of the oxide film formed on either mechanically or electrolytically polished surfaces of a 3 pct Si-Fe alloy containing small amounts of manganese after heating at low oxygen potential. The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron, 76 pct ferrosilicon, and 76 pct ferromanganese, vacuum-in-

Jan 1, 1969

By M. A. Hunter

THIS paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.0004 per degree centigrade at 2.0° C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been published by the Bureau of Standards.1 The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments are published as additional information. ELECTRICAL PROPERTIES OF PURE NICKEL It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately. 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the electrolytic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting.

Jan 5, 1922

By Van Der Muelen P. A.

SOME time ago, the writer received from W. 0. Borcherdt, Manager of the, works of the Bertha Mineral Co. at Austinville, Va., several specimens of a dense yellowish slag-like material, containing cavities showing clear needle-like crystals, and representing a product formed by the fumes of zinc oxide and basic lead sulphate from the oxide furnace, attacking the firebrick lining of the flues. The matrix, which is of a greenish-yellow color, is made up chiefly of an amorphous glass, carrying numerous crystals, the latter being well-defined, clear, and transparent, but colored a very light yellow by small amounts of ferric oxide. A number of the crystals were carefully separated from the matrix and tested with the blowpipe. They have a fusibility of about 2, yield a globule of lead and a coating of lead oxide before the blowpipe on charcoal, and contain some zinc. Their hardness is 5 to 6. 1 Fig. 1. Under the microscope the crystals appear to be made up of a prism, with narrow faces, and a fairly large pinacoid, but unfortunately show no terminal faces (Fig. 1). Between crossed nicols they gave parallel extinction in. the three planes containing the crystallographic axes, and are therefore orthorhombic. The index of refraction is high. A number of the best crystals were measured on the reflection goniometer, the angles given below representing the average of measurements made on different individuals. mm = 46° 52' mb = 66° 34' a:b:c = 0.4334:1 :?

Jan 5, 1917

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By H. V. Fairbanks

This report covers a study of three different methods for drying ultrafine coals by sound waves. Ultrafine material is classified as coal which passes through a 100-mesh sieve. During the investigations, it was found that the addition of acoustic radiation to the drying of ultrafine coal is effective in increasing the rate of drying; the effect of acoustic radiation to improve drying decreases with an increase in the temperature of the system; the drying rate increased 10-40% when acoustic radiation was introduced into a rotary kiln but was dependent upon the environmental conditions; the application of vertical vibrations to multi-tiered drying screens increased the rate of moisture removal ten times over that obtained in the rotary kiln; the formation of coal balls in any of the drier systems retards the rate of drying; the higher the initial moisture content of the coal the greater the amount of coal balls formed.

Jan 1, 1970