Search Documents

By G. W. Josephson

Since the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,l and the large-scale expansion of the industry has taken place since 1900. Historical Background Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low- priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a high degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun's rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof—conservatively, 500 per cent. Slate Graftules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate Pro-

Jan 1, 1948

Jan 1, 1966

By Ralph H. Kress

Haulage trucks designed expressly for mine service were introduced about 35 years ago. The first models to arrive on the scene hauled about 15 tons and easily outperformed the modified highway trucks that had been used for mine haulage up to that time. The specialized trucks obviously had a greater potential for mining operations, and once this fact was recognized, competitive pressures in both the mining and truck-manufacturing industries drove the new vehicles toward ever more efficient performance. Many changes in truck design resulted, but not all were accepted for a variety of reasons. Often poor design was the reason, but in many cases progressive and promising designs were abandoned only because the truck manufacturer lacked the courage, tenacity, or vision to capitalize on them. There were also many cases where a promising new design was abandoned because the prototypes were initiated in a mine where personnel lacked the patience to prove them. Truck Startup Takes A Team Ally new truck that is to succeed and contribute to lower mine haulage costs must be well conceived and launched with good teamwork on the part of all concerned. Naturally, it is essential to have a good overall truck design at the outset to make this teamwork worthwhile. The design must include the selection of the right components manufactured by suppliers that can each do justice to their particular part of the new truck. Last, but by no means least, the mine operator where the truck is to be launched must be enthusiastic in his efforts to see the new vehicle through to successful operation.

Jan 1, 1971

By SME

"Comparison of Secondary Fe-Mn Oxides in Fracture Coating and Heavy-Mineral Concentrates as Sampling Media, Silver City Mining Region, New Mexico," a technical paper, appeared in the Aug. 1983 issue of the magazine. In Table 1, page 1182, the correct sequence of the first five metals in column 1 (Elements) should read: Zn, Pb, Cu, Fe, and Mn under "Central District" and Zn, Fe, Pb, Cu, and Mn under "Pinos Altos District." The published table shows the sequences transposed under the opposite districts. All other columns and sequences read correctly.

Jan 1, 1984

By C. M. Sellars, F. Maak

Electvomotie -force measurements hazle been made on ten Au-Ni alloys at temperatures 7754 825O, 900O, and 935°C using galvanic cells with solid electrolyte. Partial and ivtegral thermodynamic functions are derived from the determined activities. which show la9,ge positive deviations jvom Raoult's law. The enthalpies of mixing- are in close accord with calorinletric data and are of comparable accuracy. The results are used to determine the miscibility gap and the spinoidal curL1e, and are qlalitaticely interpreted in terms of the large size difference and electvonic interactions between gold and nickel. Tabulated nalues of the actielities and partial and inteqal free energies, entropies , and enthalpies of mixing are given in the appendix. The Au-Ni binary alloys are of particular interest thermodynamically as despite the large size difference between gold and nickel atoms they have a simple phase diagram.' This shows complete solid solubility above a miscibility gap with a maximum at about 71 at. pct Ni and 810°C. Activity measurements (over a range of temperature) have been made previously on this system using an electrolytic-cell method with a liquid chloride eletrolyte. The accuracy of this data has, however, been queried3'4 as it leads to values for the enthalpy of mixing which are too high when compared with calorimetric measurements.46 Also, the entropy of mixing is too high when compared with the values derived from specific-heat measrements. It was therefore considered worthwhile redetermining the activity data using a galvanic cell with a solid electrolyte (0.85 ZrO, 0.15 CaO). This method is based on a technique introduced by Kiukkola and aner'' and has been used to determine the thermodynamic data for Cu-Ni alloys.' THE ELECTROLYTIC CELL The cell used to determine the activity of nickel in Au-Ni alloys was: The cell reaction, which is discussed for a similar cell by Rapp and Maak, gives a direct measurement of the activity of nickel in the alloys as where aNi(alloy) is the activity of nickel in the alloy, 3 is Faraday's constant, E is the measured electromotive force, R is the gas constant, and T is absolute temperature. For the valid application of this type of cell the arrangement must be ther modynamic ally stable, which means that: 1) The free energies of formation of the oxides fulfill the relation 2) The vapor pressures or dissociation pressures of each component must be so small that during the time of the experiment the amount of any material transported by the gas is negligible. 3) Side reactions which change the alloy composition must be negligible. These reactions are possible both with the surrounding gas atmosphere and with neighboring solid material. The first two conditions are fulfilled by the above cell.' The third condition is approached by care in the experimental technique. The factors which control the attainment of equilibrium in this type of cell have been considered by Rapp and aak, who conclude that metallic diffusion in the alloy is the rate-control ling step. A lower temperature limit for the practical application of this cell is therefore set by the condition that equilibrium must be attained in reasonable times. EXPERIMENTAL MATERIALS AND TECHNIQUE The starting materials were mint gold (99.99 pct Au) and Mond nickel (99.9 pct Ni). Alloys, nominally 5 at. pct Ni and then each 10 at. pct across the system, were produced by vacuum-levitation melting compacts of mixed drillings of the pure metals. The nickel used for the reference tablets in the cells was melted in a similar manner. The alloy ingots, cast in boron nitride molds, were cold-forged and

Jan 1, 1967

By G. F. Bolling

HE high mobility of grain boundaries in zone-refined metals has been particularly demonstrated for lead above 150°C in grain growth studies1 and in the extensive work by Aust and Rutter.1 In these investigations, no elaborate precautions were taken to eliminate oxygen from the zone-refined lead; however the alteration of creep characteristics by oxygen concentrations of less than 5 x 10 -5 wt pet

Jan 1, 1962

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

By Henry H. Logan

THE purpose of mine-hoist safety controllers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper acceleration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoisting drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of mechanical hoist controllers, the basic elements of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical connections would cut off the power and set the brakes. Since in strictly mechanical hoist controllers valuable time was lost while the various mechanical movements took place, an important development was the invention of controllers partly mechanical and partly electrical. This type of controller has a governor and movable cams to be driven in synchronism with the hoist drum, the governor representing the hoist speeds and the cams profiled to form a pattern for retardation, representing the travel of the cages in the shaft. This type is also provided with an overspeed switch and usually with a pair of selective-limit switches, one for the top limit and the other for the bottom. In overspeeding or failure to retard in accordance with the profile of the cam, the overspeed switch will be opened, or if the top or bottom limit is overrun one of the limit switches will be opened, breaking the retaining circuit of a contactor or magnetic latch, causing the power to be cut off and the brakes applied. When the speed falls to the predetermined safe speed, the overspeed switch closes, and a hoist equipped with power-operated brakes controlled in emergency by a solenoid-operated valve can be restarted immediately by simply moving the master control lever to the "off" position and then applying power-unless brake interlocks are used, in which case the brake lever or levers must also be brought to the "applied" position, after which the hoist can be restarted in the usual way. When hand-reset weights instead of solenoid-operated mechanism are arranged to set the brakes for emergency, it is necessary to reset the weights manually, besides bringing the master control lever to the "off" position before the hoist can be restarted. Should a final limit be slightly overrun, and a stop made with a limit switch held open by a cam, it is necessary for the hoistman to use a "backing-out" switch which short-circuits the overrun limit switch, reestablishing the hoist-control circuit, and simultaneously opening the

Jan 1, 1940

By Sherwin F. Kelly

Airborne techniques enter hard rock exploration field. . . the gap between pure geophysics and engineering seen as closing rapidly.

Jan 2, 1951

By G. F. Bolling

Single crystals of each metal were deformed at 77°K and heated at constant rates, variously in the range 0.125" to 4o°Kper min from 77" to -390oK, while being monitored in an X-ray diffractometer. Changes in diffraction-peak heights and line breadths were used to ascertain the temperature ranges of recrystalliza-tion. The results were subjected to the analysis of nicholas&apos; in order to obtain the rate-controlling activation energies,Q. In this analysis no recourse to a separate and distinct nucleation stage is required and the results of studying recrystallization proved consistent with the hypothesis of a constant number of nuclei or equivalent hypotheses. The values Pb = 5.5 ± 0.5 keal per mole Zn ~ 7.5 Sn - 5 Bi - 9. 5 correspond for lead, zinc, and tin to activation energies obtained elsewhere for grain boundary migration, and for bismuth and lead to previous studies of re-crystallization by Barrett.6 This correlation allows the conclusions that interference from recovery was minimal and that the observed recrystallization rates in these pure metals are effectively governed by grain boundary migration. Good agreement was not found between the results of this kind of study in zone-refined aluminum and previous work; and supplementary isothermral experiments involving hardness tests and metallography did not resolve the discrepancy. Nevertheless, at least a range,Q = 11.5 ± 2 keal per mole, can be assigned to the activation energy for boundary migration in aluminum. An experimental study of one aspect of the recrystallization process is presented here for four metals of different crystal structure. The metals chosen for study were all zone-refined to reduce impurity effects, but the attendant high purity presented a difficulty. For any reasonably high driving force a "re-crystallization temperature", TR, is in the range of 0.25 T,, where T, is the absolute melting point, and study was therefore restricted to lower temperatures. An X-ray technique under constant heating-rate conditions adequate above 90°K was devised for the study; in consequence, a newer type of analysis following Nicholas1 had to be used to obtain quantitative information about activation energies. The standard methods of studying recrystallization have involved the comparable analyses of Johnson and Mehl2 and Avrami3 which are reviewed by Burke and Turnbull.* The general analysis4 which is applied only to isothermal studies using any of various investigative techniques states:

Jan 1, 1968

By Nicholas J. Grant, Olaf Troili, John Chipman

D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—How does this effect of silica compare with the effect of silica in combining with the lime in the slag to reduce the activity of CaO, thereby affecting the first equation? John Chipman(authors&apos; reply)-—That is the object of showing this effect for slags of two different basicities. In the more basic, the silica is more firmly tied up in the slag and is less easily reduced. It is therefore less able to interfere with desulphurization. The important point is that silica is acting in two ways. Of course it is an acid and as an acid it ties up lime and in tying

Jan 1, 1952

By David Baker

Devices for saving labor in immediate connection with the operation of the iron blast-furnace have received comparatively little attention. Machines for hoisting and blowing, always employed in some form, have been improved; but charging, tapping, casting and handling the pig-iron in the beds are still performed chiefly by manual labor. At almost all furnaces, filling is done with the handbarrow of twenty-five years ago; and it is only recently that, here and there, chills have been employed in the cast-house instead of the usual sand-beds, to lessen the labor of handling the pig, as well as to secure its greater purity. The manual labor of opening and closing the tapping-hole has

Jan 1, 1893

DAVID THOMAS 1871 R. W. RAYMOND 1872-1874 A. L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HUNT 1877 ECKLEY B. COXE 1878-1879 WILLIAM P. SHINN 1880 WILLIAM METCALF 1881 RICHARD P. ROTHWELL 1852 ROBERT W. HUNT 1883 JAMES C. BAYLES 1884-1855 ROBERT H. RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B. POTTER 1888 RICHARD PEARCE 1889 ABRAM S. HEWITT 1890 JOHN BIRKINBINE 1891-1892 H. D4. HOWE 1893 JOHN FRITZ 1894 J. D. WEEKS 1895 E. O. SPILSBURY 1896 THOMAS M. DROWN 1897 CHARLES KIRCHHOFF 189S

Jan 1, 1939

BOSTON SECTION R. L. AGASSIZ, Chairman, - JAMES G. CARLETON, Vice-Chairman, E. E. BUGBEE, Sec.-Treas., Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS, G. A. PACKARD. The forty-fifth meeting of the Boston Section was held, at the Engineers&apos; Club, on Tuesday, Nov. 6, 1917. Mr. F. C. Carstarphen, tramway engineer of the American Steel and Wire Co., was the guest of the evening. After dinner, Mr. Carstarphen gave a most interesting illustrated talk on the subject of aerial tramways. The views-showed the various forms of aerial tramways and three&apos; unique installations, one carrying 285 tons of coal an hour, undoubtedly the maximum quantity transported by any tramway up to this time. The second installation is that of a lumber-carrying tramway, 5 miles long, operating in California. The last views illustrated a 13 ½ -mile tramway for carrying salt over the

Jan 2, 1918

By James Terry Duce

The gross production on the Island of Sahreirl during 1944 was approximately 6,700,000 U. S. bbl. No additional wells were drilled in the field during the year, but a number that were plugged off during the critical days of the war were brought back on production. This work is continuing. The construction of the extension of the refining plant was continued during the year and the new crude still was started in November. In Arabia, the production for the year 1940 was 5,074,838 U. S. bbl. Four wells were completed in Dammam field and all were commercial producers. Production for 1941 was 4,310,110 U. S. bbl. Seven more commercial producing wells were completed in Dammam field, and Well No. I at Abqaiq was complcted at 6180 ft. and was also a commercial producer. In 1942 production was 4,530,492 U. S. bbl. Abqaiq No. 2 was drilled to 5785 ft. but was left standing because of mechanical difficulty. The 1943 production was 4,868,- 184 with one well drilled, Abqaiq No. 3 completed at 6488 ft. and a commercial producer. Total production in Arabia for the year 1944 was around 7,800,000 U. S. bbl. and at the close of the year was running at approximately 40,000 bbl. per day. The small refinery, built in 1939, at Ras Tanura was in operation in the fall and a new refinery is being constructed. Only three wells were completed during the year—the El Jauf well in Northern Arabia (completed at 10,974 ft.) which did not bring in commercial production and Wells No. 4 (completed at 6270 ft.) and No. 5 at Abqaiq (completed at 6751 ft.), which were brought in as substantial commercial producers. Production for the year was entirely from the Dammam field. In this field, some of the wells that had been plugged off early in the war were brought back in production and this work is continuing. At the close of the year, one well was drilling in the Abqaiq field and an additional well was drilling at Qatif, the latter being a wildcat. Neither of the wells in question had reached producing horizons on the first of January.

Jan 1, 1945

EUGENE MCAULIFFE, St. Louis, Mo. (written discussion*).-When we undertook the development of the Kathleen mine, near DuQuoin, certain features greatly influenced the construction and underground development. The country is very flat, so that the usual gravity yard movement of empty and loaded coal cars would entail a very heavy fill at the empty-car end of the tracks, with some form of car-pulling arrange-ment to move the loads where it was practically impossible to provide. a gravity movement. So the yard was made level, except for 1000 ft. (304 m.) under the two tipples, where the cars are moved by gravity and controlled under the main-shaft tipple by four Fairmont car retarders. Both tipples are spread sufficiently to admit of introducing a narrow-gage track and locomotive. One 18-ton locomotive is at present employed in moving empties clown to a point above the main-shaft tipple and the loads off the track scales clown into the storage yard; ultimately a 25-ton loco-motive will be employed on the loaded side of the tipple. This form of car movement and control will admit of handling empty and loaded cars

Jan 11, 1919

By S. F. Willey

Difficulties encountered in justifying replacements for overage mobile mine equipment at the Gay mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians or computer men. The Gay mine is located 17 mi east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Co. and the FMC Corp. with 1.5-2.0 million tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24-cu yd scrapers; twenty-one 30-50-ton end-dump trucks; four 3%-4%- cu yd shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units.

Jan 9, 1972

By D. W. Smith

THE beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.1 R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 0 phase in the system copper-zinc takes the form of needles lying parallel to a [111.] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [111] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective 0 phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum.

Jan 1, 1932