Search Documents

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute's duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By F. Weinberg

It has been suggested, for some time, that the behavior of metals under high-temperature creep conditions is strongly influenced by the behavior of the grain boundaries present in the material. This has led to a number of investigations1-6 in which attempts were made to measure the properties of the grain boundaries themselves, both to determine their contribution to the creep process and to obtain further knowledge of their intrinsic structure and properties. The present investigation was undertaken to extend the observed data under more closely controlled experimental conditions and to attempt to clarify sonie of the discrepancies in the literature. A brief report of the preliminary results has been published.7 EXPERIMENTAL PROCEDURE For the present investigation, controlled orientation specimens were used having plane boundaries which terminated at the specimen surface. Trierys-tal specimens were used instead of the bicrystal type of Puttick and King,' in order to simplify the gripping technique required to apply a shear stress along the boundary. The aluminum used was obtained from the Aluminum Francaise and was of 99.994 pct purity, containing 0.002 pct each of Cu, Fe, and Si. The aluminum tricrystals were grown horizontally from the melt, in graphite boats, and in an argon atmosphere, following the technique developed by Chalmers.' The orientation of the tricrystals was controlled by using seed crystals separated by mica inserts. Thermal conditions were adjusted to produce tricrystals having boundaries which were macroscopically straight, parallel to the growth direction, and perpendicular to the top surface. Following growth, the tricrystals were carefully cut with a jeweller's saw to the test specimen shapes shown in Fig. l(a) and l(b). In Fig. 1(a), the boundaries subjected to shear stresses are indicated AB and CD: Points A and C are the ends of the mica inserts separating the seed crystals; points B and D are at lateral cuts made in the specimen. It was found that the slots left by the mica inserts at A and C had to be enlarged slightly, by cutting, to ensure that the boundary terminated freely at these points. A shear stress was applied to the boundarks by gripping the upper two legs in file-faced Inconel grips and suspending a weight from the lower part of the specimen held in similar grips, as shown schematically in the diagram. The test specimens shown in Fig. 1(b) were cut from long

Jan 1, 1959

University of Alabama University, Alabama Mining and Metallurgical Society Meets first and third Mondays each month JOHN MACLEOD MCKEE, President WILLIAM L. ALLMAN, Secretary J. R. CUDWORTH, Faculty Sponsor RICHARD L. BOWRON, Counselor University of Arizona Tucson, Arizona Millers' Society LA MONT WEST, President AL WALLACH, Secretary J. B. CUNNINGHAM, Faculty Sponsor B. R. HATCHES, Counselor

Jan 1, 1939

By H. W. Winkler, Discussion, V. L. Forsyth

The development of a new gar lift valve has removed many of the obstacles limiting over-all gas lift efficiency. The valve is pressure charged in place in a well, and operating pressure can be changed without pulling. Temperature and gas gradient compensation have been eliminated. Intermitting and constant flow installations, using conventional pressure-charged valves, are compared with designs incorporating the new automatic stabilizer controlled valve. Specific well performance data are presented. The means of obtaining and controlling multiple-point injection of gas are explained and contrasted with single point injection. The effect on small diameter strings and multiple string installations is discussed. The effect of flowing temperature gradient on a design using conventional pressure-charged valves, the limitations imposed by such temperature, and the obvious benefits which result from the use of automatic stabilizer controlled valves are shown. Reduction of gas requirements is stated mathematically and demonstrated with specific examples which are identified as to oil company and well. Increased fluid recovery resulting from greater drawdown is illustrated. The economic advantages are mentioned with emphasis on reduction of capital expenditures, as well as reduction in operating expenses. INTRODUCTION Much of the engineering and research work performed with gas lift has been based upon the supposition that under producing conditions gas would be injected at a single point in a well. Many tests were performed in determining the optimum size of the opening through which gas would be passed and the exact placement of the valve equipment. The objectives in a gas lift installation are to unload the well and to efficiently produce the well after it is unloaded. Until recently, the function of upper valves was simply to unload the well. An operating valve located at a proper place in a well served as a single injection point for lifting liquid to the surface. The basic problem in using such equipment is to arrive at operating depth with sufficient operating pressure to efficiently lift the liquid. Few gas lift installations are designed with all required well data available. However, regardless of the quality and availability of data, and regardless of the accuracy of the design, there is the practical problem of preparing and placing gas lift equipment in the well in exact accordance with the plans and intentions of the engineer. In recognition of these and many other problems, attention was directed toward a means of removing the need for temperature and gas gradient compensation, a way to change the gas lift installation to meet the changing requirements of the well itself, and a manner of compensating for changes in oil-water content, fluid volumes, PI, and bottom-hole pressure resulting from flood or repres-suring activity. A device which could actually set and change the operating pressure of gas lift valves in the well would meet most of these needs. There now exists a new gas lift valve which fulfills the original objectives and in so doing actually accomplishes much more. With this device, called an Automatic Stabilizer Controlled valve, there is an exact matching of valve operating pressure and well conditions. Gas is injected at more than one point in the well, thereby making controlled multiple-point injection of gas a reality. Installation calculations are materially simplified and the need for basic temperature and gas gradient data no longer exists. Section I—The Automatic Stabilizer Controlled Valve The operation of the ASC valve is more easily understood by first studying a conventional pressure-charged valve and then inserting the stabilizer element to observe the changes which result. Fig. 1 is a schematic of a conventional precharged pressure-operated valve. The pressure in the dome pd, acts downward, against the area of the bellows A,, to hold the valve closed. The resulting force Bf plus the spring effect of the bellows Sf represents the total force acting to close the valve. Correspondingly, the tubing pressure ptbg works upward against the port area Atbg and the casing pressure pc works upward against a portion of the area of the bellows

Jan 1, 1965

By R. G. Powell, R. Schuhmann, E. J. Michal

Liquidus surfaces in the ternary system FeO-Fe2O3-SiO2, were determined from 1250' to 1450°C by the procedure of equilibrating small samples in platinum crucibles, quenching, and microscopic examination. The experimental results were combined with previously published information to construct a ternary diagram for the system showing the entire temperature-composition range of stability of iron silicate slags. Metallurgical applications of the diagram, especially in copper smelting, are discussed briefly. IRON oxides are almost unique among the common oxide constituents of metallurgical slags in that the iron occurs in two different states of oxidation, ferrous and ferric. Moreover, in liquid slags the degree of oxidation of the iron is readily changed by reactions of the slags with oxidizing agents or reducing agents. This behavior of iron oxides in slags accounts, for example, for the effective transfer of large quantities of oxygen through slag layers in open hearth steelmaking. In this process, oxygen supplied by reactions at the gas-slag interface is dissolved in the slag with the oxidation of ferrous iron to ferric. Ferric oxide is transported across the slag layer by convection, and at the slag-metal interface the oxygen reacts with liquid metal while the ferric iron is reduced back to the ferrous state. Another group of processes in which variation in degree of oxidation of iron has great practical importance is in copper smelting. In matte smelting and converting, such large proportions of the iron are oxidized to the ferric state that problems are encountered in preventing or controlling the formation of solid magnetite. The ferrous-ferric relationship also affects the attack of iron oxides on high-SiO2 refractories, which appears to be most severe under reducing conditions for which ferrous iron predominates. Darken and Gurry' determined the chemical properties and phase equilibria of pure iron oxide slags. Their data show that iron oxide melts can have compositions ranging almost all the way from FeO to Fe2O3. The melts of lowest oxygen contents, which exist in equilibrium with metallic iron, approach ferrous oxide in composition but still have a small percentage of ferric oxide. The melts of highest oxygen contents, which have oxygen dissociation pressures of 1 atm, are above magnetite in oxygen content, with over two-thirds of the iron in the ferric state. The previously established phase diagrams for silicate slag systems all show FeO as the iron oxide component. However, Bowen and Schairer? who determined the FeO-SiO2 diagram and many of the other diagrams used by slag chemists, have been careful to point out that their systems always contained both ferrous and ferric iron. Thus, their data are for limiting mixtures with minimum contents of ferric iron, obtained by melting and equilibration in iron crucibles. Under these conditions, the Fe2O3 percentages found by analysis were small enough to justify simplification of the published phase diagrams by calculating the Fe2O3 to equivalent FeO and ignoring Fe2O3 as an additional component. On the basis of experimental measurements of melting points of iron oxides on silica in the presence of various gas mixtures, Darken3 worked out phase diagrams for the Fe-Si-0 system which show the important phase equilibria in terms of temperature and gas composition. This study clarified many aspects of the application of the phase rule to the FeO-Fe2Oa-SiO2 system and was an important basing

Jan 1, 1954

By J. B. Austin

Jan 1, 1945

By Frederick Crabtree

WHEN Professor Stock asked for a paper on the above subject, it was too late to prepare by June 1, or near that time, one that would involve any appreciable amount of experimental work or original research; but the suggestion was made that a review of the literature bearing on the subject might be submitted in good time, and that later this could be supplemented by any experimental data obtained during the summer, if experiments were carried out. In accordance with this suggestion, there are submitted the following notes on references found in the literature of recent years bearing on sulfur in gas. It is to be, understood that, ill general, these notes express the opinions of the authors whose papers are abstracted, not necessarily the opinions of the abstractors. Very little published information was found bearing directly on producer-gas sulfur, so this has been supplemented, in certain phases of the subject, by references to illuminating gas. Methods of analysis and processes for the elimination of sulfur from the gas are, without much doubt, very closely related in these two products. As in illuminating gas, sulfur is found in producer gas mainly as hydrogen sulfide, mixed with a much smaller and variable quantity of carbon bisulfide.1 The presence of minute quantities of other organic-sulfur compounds has been intimated, but no definite statement is made concerning these. The amount of sulfur present in producer gas is variable and depends on several conditions. The primary factor is the quantity of sulfur in the fuel, but the form in which the sulfur exists, the temperature of the producer, the air-steam ratio, and the efficiency of the scrubbing process are all determining factors. When the coal used contains less than 0.5 per cent. of sulfur, the sulfur in the gas will not exceed the quantity found in the average illuminating gas.2 Sulfur in producer gas may safely

Jan 9, 1919

By E. R. Brownscombe, Francis Collins

A study has been made of the material balance-fluid flow method of estimating reserves and degree of water drive from pressure and production history data. By considering the effect of random pressure errors it is shown that in a particular example a standard deviation of three and one-half pounds in each of ten pressure survey? permits the determination of the reserves with a standard deviation of 8 per cent and the water drive with a standard deviation of 15 per cent, assuming that certain basic geologic data are correct. It is believed that this method of estimating reserves and water drive is useful and reliable in a number of cases. The method is particularly valuable when reservoir pressure data are accurate within a very few pounds, but may also be applied with less accurate pressure data if a relatively large reservoir pressure decline occurs early in the life of the field, as for example in an under-saturated oil field. INTRODUCTION A knowledge of the magnitude of reserves and degree of water drive present in any newly discovered petroleum reservoir is necessary to early application of proper production practices. A number of investigators have contributed to methods of relating reserves, degree of water drive, and production and pressure history. 1-8 Three types of problems of increasing complexity may be mentioned. If a reservoir is known to have no water drive. and if the ratio of the volume of the reservoir occupied by gas to the volume of the reservoir occupied by oil (which ratio permits fixing the overall compressibility of the reservoir) is known, then only one further extensive reservoir property remains to be determined, namely the magnitude of the reserves. A straightforward application of material balance considerations will permit this determination. The problem becomes very much more difficult if we wish to determine not only the magnitude of the reserves but also the magnitude of water drive, if any, which is present. In principle, a combination of material balance and fluid flow considerations will permit this evaluation. Finally, if neither the magnitude of reserves, the degree of water drive, nor the ratio of oil to gas present in the reservoir is known and it is desired to determine all three of these variables, the problem could in principle be solved by a fluid flow-material balance analysis which determines the overall compressibility of the reservoir at various points in its history. The change in compressibility with pressure would provide a means of determining the ratio of gas to liquid present, since the compressibilities of gas and liquid vary differently with pressure variation. However, in practice this problem is probably so difficult as to defy solution in terms of basic data precision apt to be available.' It is the purpose of this discussion to illustrate the second case, which involves the determination of two unknown variables, single phase reserves and degree of water drive, from pressure and production history and fluid property data, and to study the precision with which these unknowns can be determined in this manner in a particular case. Although an electric analyzer developed by Bruce as used in making the calculations to be described, numerical methods necessary in carrying out the process have been devised and have been applied for this purpose. Schilthuis,' for example, developed a comprehensive equation for the material balance in a reservoir. He combined this with a simplified water drive equation, assuming that the ratio of free gas to oil was fixed by geological data and that a period of constant pressure operation at constant rate of production was available to determine the constant for his water drive equation. On this basis he was able to compute the reserves and predict the future pressure history of the reservoir. Hurst developed a generalized equation permitting the calculation of the water drive by unsteady state expansion from a finite aquifer. He showed in a specific case how the water influx calculated by his equation, using basic geologic and reservoir data to fix the constants, matched the water influx required by material balance considerations. Old3 illustrated the simultaneous use of Schilthuis' material balance equation and Hurst's fluid flow equation for the determination of the magnitude of reserves and a water drive parameter from pressure and production history. He used this method to calculate the future pressure history of the reservoir under assumed operating conditions. As a basis for determining reserves, Old assumed a value for his water drive parameter and calculated a set of values for the reserves, using the initial reservoir pressure and each successive measured pressure. The sum of the absolute values of the deviations of the resulting reserve numbers from their mean value was taken as a criterion of the closeness of fit to the experimental data possible with the water drive parameter assumed. New values of the water drive parameter were then assumed and new sets of the reserves calculated until a set of reserves numbers having a minimum deviation from the average was established. The average value of- the re-

Jan 1, 1949

By E. Ordonez

I have read in the Bullentin a paper by H. von Hofer relating to the Origin of Petroleum, in ehich the author supports his and Englers views, express before, of the organic origin of petroleum.

Jan 1, 1915

The opening session was held on Tuesday evening, October 23d. Mr. J. F. Lewis, on behalf of the local committee of arrange ments, made a short address of greeting to the members assembled, and then introduced Gov. A. H. Holley, of Lakeville, Conn. Gov. Holley addressed the Institute as follows: Gentlemen, we give you cordial welcome to a mining, manufac turing, and agricultural country, of which we are not a little proud. We welcome you as an association, and as individuals. We invite you to an inspection of our resources, and to our methods of im proving them. We appreciate the results of your efforts in past years, and we anticipate good from your advice and counsel in the future. You are in the vicinity of some of the oldest mining and manufacturing operations in iron in our country. It will be our pleasure to conduct you to a mine which was worked for more than a half century before our country achieved national inde pendence, and to point out to you the spot where the products of this mine were wrought into cannon and shot during the progress of our Revolution. We can show you also a far larger area of mining country than was supposed to exist in this vicinity at that early day. There are, within a radius of thirty miles from this spot, ten mines at least that have been extensively worked, and there are as many more that have been occasionally worked, with a fair degree of success. All the mines that are wrought to any extent produce excellent qualities of iron, while many of them in various combinations produce as good material for the manufacture of steel, car wheels, axles, and many other purposes, as can be found in ally country. The old Salisbury iron retains its reputation for tensile strength unsurpassed, when made entirely from the ore of the old mine. The progress that has been made in the development of these mines since the days of the pickaxe, when the product was trans ported in pounds upon horseback, to those of the steam-engine, which now moves hundreds of tons per day, presents, indeed, a

Jan 1, 1879

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential, but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for converting a prospect into a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is usually headed by an engineer-promoter or an entrepreneur trader who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the ha1 operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1964

By Charles Wurms, Robert Steinitz

DURING an investigation to determine the compatibility of several metals with tungsten, the degree of reaction between tungsten and lead was determined. A literature survey showed considerable disagreement between the results of various earlier investigators. Information presented by M. Hansen1 states that, according to S. Inouye,2 tungsten has very poor resistance against attack by molten lead, even at the low temperature near the melting point of lead. A phase diagram in the same reference indicates a solubility of 30 wt pct W in molten lead at 1300°C. Contrary evidence was shown by Parkman and shepard3 in their investigation of materials for use in heat transfer systems containing liquid lead alloys; they performed experiments at 980°C for times up to 50 hr without noticing any appreciable attack on the tungsten. Tungsten sheet was immersed in molten lead contained in Vycor tubes evacuated to at least 10-4 mm Hg. R. Bernard4 and R. I. Jaffee5 also indicate that no reaction occurs between molten lead and tungsten. However, no experimental data were included in these reports. In order to settle the question of the solubility of tungsten in molten lead, tungsten powder with an average Fisher subsieve particle size of 6µ was pressed in a double-acting die at 6 tsi to small compacts. They were then sintered in an atmosphere of hydrogen for 2 hr at 1700°C, resulting in a sintered density of 64 pct of theoretical with final dimensions of 0.260 in. in height and 0.245 in. in diameter. For all tests, the tungsten pellets were immersed in molten lead. Table I is a summary of the experimental procedures showing atmospheres, temperatures, and times. The first experiments were performed at 650°C; at this temperature, the liquid lead should wet the porous tungsten better than at its melting point, and penetrate into the pores. The lead was heated in a graphite crucible with a graphite cover. No protective atmosphere was used, as it was expected that the formation of CO would be sufficient to prevent oxidation. This, however, proved to be wrong, and all tungsten samples showed a slight oxide film after treatment. The tungsten samples were immersed in the molten lead for times of 5 min, 10 min, 1/2 hr, 1 hr, and 2 hr. After this time, the melt was poured into a form and the

Jan 1, 1962

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer's nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

At its meeting on June 22, 1950, the Board of Directors passed a resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters On June 23, 1959 the Board of Directors made minor revisions in the resolution to bring it up-to-date with recent changes in the Institute's structure The revised resolution IS as follows

Jan 1, 1960

By Donald E. Crowell

Due to falling metal prices and depletion of ore reserves, lead- zinc mining in the Leadville, Colo., area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Co. and Asarco, with Asarco being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Co. of Salt Lake City in conjunction with the central engineering department of Asarco. The plant was constructed by Stearns-Roger Corp. Construction began in the spring of 1970 and the plant went onstream in April 1971.

Jan 11, 1972

By A. H. Shoemaker

THE shutdown of Homestake by Government order L-208, with its consequent disruption of a very stable and trained working force, coupled with postwar inflation and the coincidence that a mining depth had been reached that posed problems of ventilation, access to exploration areas, and choice of mining methods that would be applicable to zones of greater rock pressures made a very searching analysis of every phase of Homestake's operations a necessity. Any changes to be made had not only to meet the problems of deeper mining but also had to provide greater efficiency so that the mine might operate at a substantial profit until such time as a gold price adjustment might be forthcoming that would offset post-1945 inflation. Geology and Mining Situation The Homestake mine lies in the northern Black Hills in an area of Pre-Cambrian rocks exposed by the erosion of the paleozoic formations which covered the Black Hills. The Pre-Cambrian rocks in the vicinity of Lead comprise metamorphosed sediments with a total thickness of about 20,000 ft. The oldest formation, the Poorman, is ankeritic carbonate schist. The next oldest, the Homestake formation, host rock for all Homestake orebodies, is a siliceous iron-magnesium carbonate schist. The younger formations are dom-inantly argillaceous with some quartzites. Tertiary intrusive rocks cut all formations. The Pre-Cambrian rocks have undergone extreme isoclinal folding. Superimposed on this intricate folding are zones of shear folding which cross the isoclinal folds at small angles. The Homestake orebodies are pipelike replacements of the Pre-Cambrian Homestake formation where certain cross folds intersect some earlier isoclinal folds. These orebodies plunge flatly to the southeast at variable angles locally as steep as 45". The orebodies are replacement areas where numerous vein quartz of irregular shape have formed with surrounding zones of chlorite alterations containing disseminated sulfides and metallic gold. Where the numerous individual quartz veins with the sulfide and gold-bearing alteration zones are close together, large irregular orebodies with a roughly elliptical plan outline result. These ore zones may be more than 200 ft wide and 700 ft long in plan area. They have followed down the plunge of certain severely folded structures with great persistence. Two vertical operating shafts, the Ross and Yates, serve the mine, one with rope capacity to reach the 4850 level, the other to the 5000 level.

Jan 1, 1959

By D. A. Schemnitz, O. W. Ellis

Certain alloys1 that, as a result of quenching, are retained in the form of homoaeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys2 that, on rapid cooling, are held in the form of homogeneous solid solution, as, for example, certain steels, behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as " aging"' or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 1, 1925

By Thomas MacFarlane

In smelting copper, lead, and silver ores, it is scarcely possible in every case to make analyses of the various parcels of ore, with the view of combining these and the fluxes so accurately as to yield, in the furnace, slags of exactly the most favorable composition. This is even more difficult with ores which require previous calcination, or with mattes which have been roasted in heaps. Even in cases where the greatest pains have been taken and the most elaborate calculations made beforehand, it frequently happens that variations in the working of the furnace interfere with the result so much desired. Generally, the practical metallurgist must be content with ascertaining the average composition of his ores and fluxes, making a calculation once for all as to the most advantageous mixture, and leaving slight changes in its composition to be taken care of as it is passing through the furnace. The various products then afford him the best material whereon to base his judgment as to the manner in which his smelting mixture is working. Of course the character of the slag is one of his chief guides, but it is not always possible from its outward characters alone to form a correct judgment as to its composition. Neither would it be possible or practicable to apply chemical analysis for this purpose, as it would be impossible to wait for its results while working a furnace. Abich was, I believe, the first to point out the relation existing between the composition of volcanic rocks and their densities, and to show that, the latter being ascertained, very correct conclusions

Jan 1, 1880

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939