Search Documents

By W. W. Mullins

The development, by the mechanism of volume diffusion, of a grain boundary groove on an interface separating a solid phase and a saturated fluid phase is calculated under the following assumptions: 1) isotropy of the interfacial free energy 's, 2) applicability of the Gibbs-Thompson formula relating curvature and chemical potential, 3) a nearly planar groove surface. The groove profile is found to have a .fixed shape and linear dimensions that are proportional to (time)1/3. The constant of proportionality is evaluated and involves ?s in such a way that the latter my be evaluated from grooving kinetics. A grain boundary that intersects an interphase interface will tend to produce a groove along the line of intersection (Fig. 1). The ultimate motivation for the formation of the groove is the reduction in interfacial free energ that occurs as the grain boundary contracts. Smith has discussed the way in which the free energy of the interfaces determines their dihedral angles at the groove root and has given a detailed analysis of the effect of the dihedral angles upon the nature the microstructures developed in polyphase alloys. Herring2 has extended the considerations to the case in which the free energy of an interface depends on its orientation and has thus added torque terms to the condition for interface equilibrium. Although the grain boundary and the interphase interface may quickly achieve the proper equilibrium angles where they intersect, as determined by the balance of equivalent tensions and torques,"2 the groove will generally continue to grow (though with decreasing speed). Thermodynamically, this continued growth reflects the fact that the lowest free energy cannot be achieved until the entire grain boundary has been eliminated; mechanistically, the growth occurs in response to inhomogeneities of chemical potential that are caused by the constraint of fixed dihedral angles at the groove root. The latter point is illustrated in Fig. 1, which shows that atoms* near the groove are on the convex side of a cylindrically curved surface and therefore have a higher chemical potential than atoms on the flat interface beyond. Thus atoms tend to leave the curved groove shoulders and force the groove to deepen. When both phases are solid additional chemical potential gradient may arise from whatever strain fields are necessary to insure continuity of material across the interface. In the discussion that follows, this complication due to strain will not occur since we always assume one phase to be a fluid and the other a solid. The transport processes that may operate to permit growth of the groove are surface (interface)* diffusion, volume diffusion in the phase on either side of the interface, and evaporation-condensation when one phase is gaseous. (Also a melting-freezing process is responsible for groove enlargement on a solid-melt interface as discussed in Sec. VI). The theory of grain boundary grooving has been discussed in detail for the processes of surface diffusion and of one type of evaporation-condensation.3'4 The theoretical predictions for the mechanism of surface diffusion have been confirmed in an experimental study of grooving kinetics in copper.5 In this paper, the theory of groove development by volume diffusion will be presented. Volume diffusion can occur either by atomic migration in the solid S or by diffusion of S atoms in the fluid phase, or solvent, adjacent to the groove surface. As discussed in Sec. V, volume diffusion in the solid should be less important than surface diffusion in forming a groove. Apart from verifying this statement then, the main interest of the present analysis centers on diffusion in an external solvent. The solvent may be either a liquid (e.g., water, or-

Jan 1, 1961

By R. M. Board

This paper will focus on measurement and control of four main aspects of crushing, namely horsepower, bowl level, mantle position and feed rate, and will discuss related sensors and control techniques, some of them designed specifically for crusher control, that have proven successful and reliable in many installations.

Jan 1, 1982

By Zay Jeffries

A MORE complete interpretation of the amorphous theory in metals is given than has heretofore been offered. It is believed that Le Chatelier, Tammann, and Heyn, at present the ablest opponents of the amorphous theory, will not he able longer to continue their beliefs that surface tension alone can account for all the observed variations in the properties of single constituent metals. It is strongly advocated that the properties of any solid substance be studied from the standpoint of the number of constituents present, the quantity and arrangement of each constituent, and the properties, of each constituent. Each deformable crystalline constituent by plastic deformation will produce amorphous material, thus changing the properties. Considerable attention is given to the variations in properties of the amorphous and crystalline phases of any substance. These are summarized as follows: 1. The cohesion of the amorphous phase of a substance is substantially zero at the melting point while the cohesion of the crystalline phase is considerable at the melting point. With decrease in temperature, the cohesion of the amorphous phase increases at a faster rate than that of the crystalline phase; this differential rate of change of cohesion holds between absolute zero and the melting point. At a certain temperature

Jan 2, 1919

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

A new apparatus termed a "distribution analyzer" is introduced to ascertain the optimum conditions of electrostatic separation of minerals. It was found that with similar surface condition, testing environment and a constant feed rate of not higher than one layer of particles fed on the grounded roll of the separator, the behavior of each component mineral in a synthetic mixture or ore is roughly similar to that of the same mineral when tested alone.

Jan 3, 1950

By J. F. Bryson

Instantaneous outbursts of coal in underground workings have occurred frequently in various coal fields in Nova Scotia; British Columbia; Canada; South Staffordshire, England; and the states of Washington, Virginia, West Virginia and eastern Kentucky in the United States. Such outbursts in eastern Kentucky have been called "mountain bumps " because they are more likely to occur under mountain cover than elsewhere, but recently they have become generally known as "coal bumps." The eastern Kentucky coal field has been troubled by these outbursts since 1923. Many men have been injured and killed, and the morale of the workmen in the vicinity of such outbursts has been affected to such an extent that mine production has suffered for a considerable period following each outburst. Such phenonlenal occurrence in any coal field naturally has led to discussion as to the cause and means of prevention. In the eastern Kentucky field, local mine officials, workmen, mining engineers, and many others have offered many ideas as to the cause and many methods of prevention have been suggested, and tried without success. Some of the plans were either practically or economically unsound and in general impossible to follow. To enumerate all the suggestions would require a large volume. One cause mentioned was that they might be due to gas under high pressure, as in Lower Silesian mines, and the remedy reeommcnded was to drain the gas by drilling holes into a suspected area. A hole 30 ft. long was drilled into a 60-ft. pillar to allow the gas to drain off, hut the pillar bumped the next day. Realizing the importance of obtaining the best information available on coal bumps, the writer, with the permission of the Harlan County Coal Operators' Assoeiation, invited Mr. George S. Rire, Chief Mining Engineer of the U.S. Bureau of Mines, who had investigated bumps in several countries, to conduct an investigation of coal bumps in this field. Mr. Rice, by permission of the Director of the G.S. Bureau of Mines, accepted the invitation, and it was the writer's privilege, in company with

Jan 1, 1936

By C. G. Durdaller, W. H. Robinson, G. M. Pound

The nucleation rate of the a (pay) to 0 (white) tin transformation was measured as a function of temperature and a tin particle size using an X-ray diffraction technique. The powder specimens of a tin were essentially monodisperse and the small dinzension of the particles of these specimens was varied from 13 to 75 p. Several types of nucleation sites of differing potency were fbund to be operative in the nucleation process, but it could not be determined whether these sites were on the free surface of the tin particles or within the volume. Assuming that they were on the free surface, the average density of the most potent sites was calculated to be 2.5 to 5.3 x 10' sites per sq cnz through the application of a Poisson distribztion finction to the isothermal data. Analysis of the temperature dependence' of the rate constmts at a given fraction transformed suggests that the active sites are regions of higher free energy and not catalytic interfaces. Appreciable induction periods were observed at the lower temperatures of transformation. Experimental studies1 of solid-solid phase transformations have led to the belief that the new phase nucleates at structural imperfections. The purpose of the present work was to learn more about the mechanism of nucleation in solids and the nature of the singularities at which nucleation occurs. In this investigation nucleation rates in the isothermal transformation of gray to white tin were measured by an X-ray diffraction technique using essentially monodisperse powders of gray tin. This particular phase transformation was chosen for study because it presented fewer experimental difficulties than most others. The experimental temperature-control problems were minimal because the two phases coexist in equilibrium at 13.3"C, and measurable transformation rates occur at temperatures only slightly above room temperature. The growth rate of the P phase into the a2 is sufficiently fast to make the measured transformation rate equivalent to the nucleation rate, provided that the particle size of the samples is small enough; for the experimental temperatures used in this study, the particle diameter must be less than 100 p. EXPERIMENTAL TECHNIQUE The P tin used in this study was obtained from Capper Pass and Son Ltd., North Ferriby, Yorkshire, England, and was of 99.999 pct purity. It was transformedS to the a phase and ground into a fine powder in an agate mortar. This powder was separated by a Roller air classifier into seven fractions whose dimensions, as determined by microscopic measurement of many thousands of particles, are given in Table I and whose distribution of size within each fraction is given in Figs. 1 and 2. The shape of the particles was roughly that of an oblate spheroid,

Jan 1, 1964

By K. C. Strebig, C. W. Schultz, A. A. Selim

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory. The drill was designed to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation and an equation representing the bit performance was derived from the mathematical theory of reliability. The drilling torque was found to increase with the use of additives while the sliding coefficient of friction and the wear coefficient decreased. The energy per unit volume consumed was found to increase with the use of additives. A hypothesis explaining the effects achieved with the additives is given. INTRODUCTION For some time researchers have attempted to increase drilling efficiency by adding certain agents to the flushing medium. Much of this interest is the result of the observations of Rehbinder, Shreiner and Zhigach1 They postulated that "...in processes for the mechanical destruction of solids, a region of increased crack formation is created in the deformed layers adjoining that surface of destruction, forming the predestmction zone. The surrounding medium (for example, a liquid) which wets a given solid will penetrate the embryo microcracks of the predestruc-tion zone. Increasing the molecular affinity of this liquid for the surface of the solid considerably facilitates the deformation and destruction by softening the solid in the zone of increased crack formation. In this manner, the hardness or strength of the deformed body is decreased by the influence of the penetration of the liquid into the predestraction zone." This is known as the "Rehbinder effect". Rehbinder's work has prompted many investigators to examine the effect of additives on the mechanical destruction of rocks. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the solution.* Robinson reported that his results did not appear to support the theory of Rehbinder.3 Joris and .McLaren suggested that additives with surface tension lower than water will be more efficient in cooling the diamonds.4 Their effectiveness in removing the fine cuttings from the face of the bit will also improve the efficiency of the system. They reported an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. In contrast, Long and Agnew, drilling with surface set bits, reported that lubricating agents increase bit temperature and wear.5 A significant change was reported6 in the mechanical properties of rock with polar additives. It was concluded that this change in the mechanical properties of the rock in the presence of the additive is due to the rock hydrophilic properties. Ethylene glycol, glycerine and anionic detergent were selected for this investigation because their surface tension is lower than that of water. The surface tension of these additives for the concentrations studied was 42 to 75 percent of the surface tension of water. A low surface tension additive would wet the surface of the diamonds more easily and hence would be more effective in cooling the diamonds. Another characteristic of these low surface tension additives is their effectiveness in removing the cuttings and preventing the flocculation of the formed particles in the drilling process. This article summarizes the results of an investigation performed at the laboratories of USBM, Twin Cities Mining Research Center. The objective of the investigation was to study the over-all effects of some organic additives on the performance of diamond impregnated bits in atmospheric drilling conditions only and not in downhole pressured conditions.

Jan 1, 1970

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

By Howard Eavenson

THE mines of the United States Coal & Coke Co. are located in the Pocahontas coal field, in McDowell County, West Virginia. Twelve plants have been opened and equipped, of which, by reason of the present business depression, only nine are now in operation. These twelve plants serve eighteen mines; some of the plants having several openings, in either the same seam or in different seams, tributary to the same tipple. Only nine of these mines are now being worked at the plants in operation. Construction work was begun in 1902, and coal from the first three plants started was shipped in December of that year. An additional plant was opened in 1903, two in 1904, two in 1905, two in 1907 and the last two in 1908. On Jan. 1, 1915, the plants have been in operation an average period of 8.8 years. The rules of the company, which have been in operation since work was first begun, are similar to those in use by the H. C. Frick Coke Co. at its mines in Pennsylvania, in which "Safety First" was incorporated as early as 1907; and it has always been the policy of both companies to look carefully after the safety of their employees. Although the field is an extension of the old Pocahontas field, the mines, located upon a new branch railroad, are away by themselves, and, as is usual in such cases, the class of labor attracted at first was temporary in character. The rapid development of the mines required the employment of many new men and officials each year; and, while the accident record from 1904 to 1909 was as good as the average of the field, it was felt to be not as good as it could be made, and a determined campaign was inaugurated for preventing accidents of all kinds. Fig. .1 shows the tonnage of coal produced per fatality, both total and for inside accidents only, at our mines; the tonnage per fatality of all West Virginia mines, and of those in the Pocahontas field.

Jan 2, 1915

By W. C. Winegard, C. J. Simpson, C. J. Beingessner

VARIOUS organic compounds, such as borneol, carbon tetr a bromide, and hexachloroethane, solidify as transparent plastics with a fcc structure. Each of these substances undergoes a solid-state transformation from the plastic phase to a brittle phase at temperatures slightly above 20°C. Since it was known that these plastic crystals solidified like metals,1 it was decided to investigate the possibility that solid-state grain growth would occur in the same way as it does in metals. Two-dimensional grain growth in thin films of plastic organic compounds has been studied with the aid of cinemicrophotography. Samples varying in thickness between 250 and 1000 @ were prepared by subliming a thin layer of the compound onto a microscope slide plate which was then covered with a second slide plate.

Jan 1, 1968

By H. R. Hendricks

The ore of the Iron King mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalcopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the non-sulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pet minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. Development of Present Flowsheet and Milling Practice The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (I) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pet, zinc 7.60 pct, copper 0.22 pct, iron 22 pct and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation mas practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1949

By Chingyuan Y. Li, C. Y. Hsieh

REALIZING that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. ALUNITE Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. [ ] Other alunite deposits have been found in Kiangpei, Szechuan province; Channing, Liuyang and Hsanshan, Hunnan province; Tsingchow and Chowyuan, Shantung province. No reserve figures are available. HIGH-ALUMINA SHALE Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China (Table 2). [ ] In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* SHANTUNG BAUXITE Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (Si02) and mineral composition (diaspore) are dis-

Jan 1, 1946

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

By John Bell

Aim of Rock-Crushing Experiments THE aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately, as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial. types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½ -ft. Huntington mill was used.

Jan 2, 1917

By G. Y. Chin, W. F. Hosford

It has long been recognized that, for a crystal to undergo an arbitrary shape change by crystallographic shear, at least five independent shear systems must be activated. Taylor1 analyzed the deformation of fcc crystals by {111}<110> slip and showed that the principle of minimum work could be used to determine which combination of slip systems might act to produce a given shape change. Later Bishop and Hi112 attacked the same problem by first identifying the state of stress which could physically activate five or more {111)(110) systems simultaneously and then invoking the principle of maximum virtual work to determine which combination would act for a given shape change. Taylor&apos;s general approach has been used to calculate the active slip systems and the relative strengths during axisymmetric flow of cubic crystals with other deformation modes, including {112}<111> slip3 and {111}<112> twinning.&apos; It is the purpose of this note to identify the stress states capable of activating simultaneously five or more of these systems. {111}<112> Twinning. The {111}<112> systems are defined in Table I and illustrated in Fig. 1. The sense of the shears are those for twinning in fcc crystals. The shear stress on any system may be written in terms of the stress components expressed relative to the 1,2,3 cube axes. For example, the stress For five or more of the systems ij to be activated simultaneously, it is necessary that Tij/T be equal to unity in at least five of the expressions [3], while Tij < T for the remainder. (These restrictions assume that the same shear stress T is required to activate each system and that the shear stress on any system cannot exceed that for its activation.) The discrete values of the stress components A through H which can satisfy these restrictions are listed in Table II together with the values of Tij/T for all systems. It may be noted that Tij/ T is not necessarily zero on all nonactive systems as found by Bishop and Hill for <110> {111} slip. In fact, for the case of twinning Tij/T may reach negative values as large as -2 for shear stress in the reverse direction, Table 11. This means that, if those stress states are to be valid, the shear stress to activate reverse twinning must be greater than twice that for forward twinning. Such stress states are probably valid in view of the directionality of the twinning process. There has been no documentation of reverse twinning thus far. It may be noted that the stress states fall into four classes, which may simultaneously activate eight, six, six, and five twin systems respectively. These solutions may be applied to the {112}(111)

Jan 1, 1970

By Victor Phillips, J. P. Blair

Jan 1, 1952

By C. Richard Tinsley, Ta M. Li

Accelerated development of the deep-ocean and continental margin resources may be the ultimate answer to meet rapidly increasing material demands to the year 2000. The mineral-rich oceans that have been described as "vast" and "nearly inexhaustible" have to date remained virtually untapped. Mineral Dependencies Trigger US Interests A lack of known domestic reserves of selected commodities and a climbing mineral trade deficit that reached a record $19 billion in 1974 are two factors that have sustained US interests in deep-ocean and offshore mining over recent years. But the lack of federal leadership in formulating ocean mining policy is said to have significantly discouraged the major capital commitments necessary to develop these resources.

Jan 4, 1975

By Hugh S. Spence

IN the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mattawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were &apos;found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by Inspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the summer of 1942 to inspect the property,

Jan 1, 1947

By E. S. Bardwell

Each of the three refining furnaces in use at Great Falls is provided with a waste-heat boiler. The general arrangement of furnace and boiler is as shown in Fig. 1. Two of the furnaces have hearths 45 ft. 7 in. by 14 ft. 6 in.; the third has a hearth 46 ft. 101/2 in. long and of the same width as the other two. The furnaces at present are equipped for firing with natural gas. As originally constructed two of the furnaces had hearths 36 by 14 ft., and were designed to use coal on grates, but these furnaces were lengthened and fired successively with pulverized coal and oil. The third furnace was added in 1926 and was oil-fired until 1928. Since that year natural gas has been in use on all of the furnaces. The changes that have occurred in connection with furnace design and the comparative performance of the furnaces with various fuels were described1 by the author in 1932. Two of the furnaces are provided with Stirling class A-30 boiler. rated at 400 hp. and having 4008 sq. ft. of heating surface. The thir furnace has a class A-21 Stirling waste-heat boiler rated at 300 hp. with 2805 sq. ft. of heating surface. The boilers are not baffled. The waste-heat boilers are placed on a platform 17 ft. 3 in. above the level of the furnace charge floor. The waste gases from the furnace pass by a vertical uptake flue, 4 by 3 ft. inside at the point where it enters the chamber, to a brick chamber from which the gases pass over a bridge wall and into the boiler setting. The uptake flue and chamber are constructed of silica brick. Each furnace has a steel stack 125 ft. high, measured from the boiler floor. The stacks have a 41/2-in. firebrick lining and are 5 ft. in diameter

Jan 1, 1934

By James F. Kemp

In submitting an additional contribution to the discussion on ore-deposits in the recent volumes of the Transactions, it is my desire to adhere closely to matters of material importance as affecting the actual processes. Judging from the discussion by Professor Van Hise, and from one or two reviews or other articles by associates of his in geological work, the impression seems to prevail that, in so far as my paper* referred to his masterly essay, I was guilty of misconceptions regarding both the part attributed by him in it to the igneous rocks and the ubiquitous presence of the ground-water. I should regret extremely to be wanting in these particulars or to have misunderstood one for whose great services in this and other branches of geology no one has a higher esteem than myself. I have, however, in the most careful way, and with these points in mind, read his essay again, and, taking it as a whole, I cannot gain any different impression of relative magnitudes than the one first received. The importance of the igneous phenomena and the restrictive influence of the processes described by " cementation " in their effect upon the ground-water, as set forth in Professor Van Hise&apos;s "Discussion" (Trans., xxxi., 292), impress me as being in very marked contrast with the same things in his first essay. If the point seems to anyone of sufficient importance, it can easily be decided by reading the originals. My paper was the result of some years of observation, reading and reflection, and was meant to be an independent contribution, controversial only in some subordinate particulars. In depicting the drama of the deposition of ores, I cannot but feel that Professor Van Hise assigned to the chorus and the scene-shifters some characters which, it seems to me, should

Jan 1, 1903