Search Documents

By John Tyssowski

In 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temperatures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several particles had become one unit. From this discovery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the application of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper produced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles. Concurrently, the three metallurgists worked on the problem of effecting a complete union of the cathode particles. Adequate washing was all that was needed to free the particles from electrolyte solution and slimes. A press was designed to produce briquettes of the proper porosity and density, and a method was devised of removing surface oxidation from the particles of cathode, by treatment in an atmosphere of deoxidizing gas at an elevated temperature. The temperature was determined at which the surface cleansing and preheating could be done in one operation, and for this a charging and preheating furnace in which there is maintained a positive pressure of deoxidizing gas atmosphere was designed. And finally, a method of feeding the heated briquettes of deoxidized cathode copper into an extrusion press without contamination from the air was evolved. For the final stage, a press was required because not only heat but pressure was required to obtain complete growth of the new crystals between the cathode particles as well as the elimination of all voids or non-coalesced areas. All essential stages of the process are protected by patents or patent applications in the United States and principal foreign countries, and the copper is produced on a commercial scale.

Jan 1, 1941

By Axel Sahlin

The day is long past when linen and cotton rags were the exclusive raw material of the paper-trade. Wood-fiber, chemically or mechanically prepared, straw, hemp and Esparto grass have largely supplied the demand, which the old materials did not suffice to fill. But even these newer fibers have been of late supplanted, to some extent, by mineral pulp. Weighting and filling materials have also been resorted to, partly to give body to the fabric, partly to increase its weight and reduce the cost per pound. China clay, sulphate of lime and soapstone have generally been employed as loading materials. Even though these materials lack fiber, their addition must by no means be viewed, as it too generally is, entirely as an adulteration. No doubt, to a certain extent, they weaken the paper ; but for ordinary grades the addition of these non-fibrous substances is a positive advantage, as they close the pores between the fibers and lend to the paper a great degree of opaqueness and a superior finish. Fibrous talc, as a form of pulp, has the same effect, without appreciably weakening the paper. When, therefore, some fifteen years ago, fibrous talc in large quantities, and of marvellous purity and whiteness, was discovered in the neighborhood of the town of Gouverneur, it was not long before the

Jan 1, 1893

By W. E. Hall

The Darwin mining district of California, 160 miles north of Los Angeles, has yielded an estimated $45 million in lead, silver, zinc, and copper since 1875. The deposits are in silicated limestone of Penn-sylvanian and Permian age close to a stock of horn-blende-biotite-quartz monzonite. Steep left-lateral strike-slip faults that strike N 50o 70o E served as feeder channels for the ore solutions, and minor folds, favorable beds, and faults close to the feeder channels localized the orebodies. The orebodies are irregular, steep, pipe-like replacements that cut across bedding, bedding replacements, and fissure fillings in a calc-silicate country rock consisting mainly of wollastonite, grossularite-andradite garnet, idocrase, and diop-side. Near surface the ore consists of a soft, crumbly mass of cerussite, hemimorphite, jarosite, limonite, and some secondary copper minerals. The primary ore consists of galena, sphalerite, pyrite, pyrrhotite, and chalcopyrite with smaller amounts of andorite, matildite, scheelite, tetrahedrite, and a high silver-lead-bismuth-selenium-bearing galena. Preliminary X-ray fluorescence study of the primary ore has indicated unusually high concentrations of bismuth, selenium, and silver in galena from certain parts of the mine. One phase of this study concerns the distribution of these elements. Twenty-two samples of galena and thirty of sphal- erite have been purified and analyzed or are being analyzed. The selenium in 21 samples of galena ranges from 0.0045 to 2.11 pct; four contain more than 1 pct. These four samples were collected from the Essex orebody, where most of the selenium is concentrated. Three are from high-grade, near-surface ore, and one is from the 700 level. Four of the seven analyzed galena samples from the Thompson workings immediately north of the Essex orebody contain 0.29 to 0.74 pct Se; the others show less than 0.05 pct. Galena from the Defiance workings about 2000 ft south of the Essex has less than 0.03 pct Se. The selenium-bearing galena also contains concentrations of bismuth and silver. Preliminary spectographic analyses indicate as much as 3 pct Bi and more than 1 pct Ag in galena with high selenium content. Antimony is the only other minor element present in galena in amounts greater than 0.02 pct; most galena contains between 0.1 and 0.2 pct and the maximum is 0.72 pct. A second phase of the study is an attempt to determine the temperature range of the formation of the ore. The iron content of sphalerite deposited in equilibrium with pyrrhotite is being used as a geologic thermometer as it is a function of the temperature of deposition of the ore.' Preliminary results indicate temperature range from 430°C in replacement orebodies in the Defiance workings to 180°C in shallow fissure fillings.

Jan 1, 1960

Although the Suggestions to Institute Authors, as revised and amplified over the years to meet changing conditions and experience, have had as their primary objective the guidance of the author who is preparing a paper for record in the TRANSACTIONS, there are in this current version many excellent suggestions for the preparation of any material for publication by the Institute In this connection it should be emphasized that in a sense, and to a degree determined by the editors, the Institute has in its journals "a place for everything," especially a place for the article of practical nature that is of immediate but not necessarily permanent interest Such articles may be referred by the Institute Technical Publications Committee to the editors or submitted directly to them , [Papers (TECHNICAL PUBLICATIONS and TECHNICAL NOTES) authorized for the TRANSACTIONS are, with the discussion, gathered together at the end of the calendar year and with a table of contents and index, bound, according to Branch classification, as volumes of the TRANSACTIONS

Jan 1, 1952

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, get in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has ken mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been almost entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is anlazing that the iron companies will persist in sending abroad under heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests mere canducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition: Water,....2.68 Silica,..........65.48 Iron oxide,.........2.10 Alumina,.........15.02 Magnesia,... 15.35 10061

Jan 1, 1882

By Thomas C. Atchison

An understanding of the physical processes involved in breaking rock with explosives will lead to better blasting techniques. In this chapter known rock breakage principles will be outlined, some conjectural ideas will be discussed, and areas needing further study will be pointed out. The principles outlined will serve as a basis for the design of blasting rounds described in the following chapter. 7.2-1. Factors Important to Rock Fragmentation. The efficacy of explosives as tools for rock fragmentation lies in their ability to deliver almost instantaneously large amounts of energy to a limited portion of the rock. When an explosive charge is detonated in a drill hole, its energy is released in a very small fraction of a second in the form of gas at extremely high pressure and temperature. The mechanics of the transfer of this energy to the rock and the resulting breakage are complex and not completely understood. Factors that have been identified as important to the fragmentation process may be grouped in three categories: explosive parameters, charge loading parameters, and rock parameters. EXPLOSIVE PARAMETERS. Explosive parameters known to influence breakage are density, detonation velocity, detonation impedance, detonation pressure, gas volume, and available energy. Detonation pressure is probably the best indicator of an explosive's ability to break solid hard rock. Detonation pressure is roughly proportional to the product of density and the square of the detonation velocity. The relative ability of different explosives to transmit their pressure to stress in a given rock is function of their detonation impedances. Detonation impedance is the product of density and detonation velocity. The volume of gas released in the explosive detonation undoubtedly is of importance, at least in the later stages of breakage, and is probably

Jan 1, 1968

Draftsman and transitman for coal mine work in Middle West. Salary $125 per month. No. 277. Mechanical draftsman familiar with mill and machinery design for metallurgical and chemical plants. Advise experience, salary expected, and references. No. 289. Two cyanide shift bosses, one cyanide mill supt, and one assayer, for work in South America. Expenses clown and return if two year contract is made. No. 290. In assay laboratory of University in the Middle West, man to take charge of ore-dressing and. help in assay laboratory work. Willing to give right man assistant professorship. No. 291. Experienced appraisers familiar either with field or office methods, capable of field survey of the physical properties and able to check up their survey on the books of the company, which require a very intimate knowledge of accountancy. Salary $2000 to $2700. No. 292. Young man trained in chemistry and engineering to conduct experimental work on storage of coal. No. 293.

Jan 4, 1918

Discussion of the paper of R. H. RICHARDS and BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 191.5, pp. 67 to 72. R. H. RICHARDS, Boston, Mass.-I believe that the manner of working for efficiency in almost all lines is to study the conditions of highest efficiency, and then to measure what is being clone. We can then see how near we have approached the highest efficiency. Spigots in practice often use many times the water theoretically needed. There are places where that is necessary for safety reasons. There are, however, places where it is unnecessary, and in these places it seems to me that this work of Mr. Dudley's will be a great help to the mill man to arrive at the greatest economy of water and highest efficiency. ALBERT R. LEDOUX, New York, N. Y.-A good many years ago I received a telegram from that distinguished engineer, Hamilton Smith, which simply said in substance: "I have discovered that liquids will flow faster from a square orifice than from a round orifice of the same area, under the same head." I wondered why he sent me the telegram, but some time afterward he told me that he had been making experiments along that line in Montana; that he thought the discovery was interesting

Jan 5, 1915

By Theodore Holt

Outline of the Process THE Mines Operating Co.'s plant at Park City, Utah, was designed to treat the low-grade fillings in the old stopes of the Ontario mine. These fillings carry 6 to 14 oz. of silver, 1 to 2 lb. copper, 0.01 to 0.015 oz. of gold, and a small percentage of lead and zinc. The treatment consists in mixing the crushed ore with coal dust and salt and then roasting in a new type of furnace y combustion of the contained fuel. The roasted ore is leached with an acid salt solution to dissolve the silver, gold, copper, and lead. At present these metals are precipitated together on scrap iron and the product sold to a refinery. The only new feature of importance in this scheme of treatment is the roasting process, which makes possible the chloridizing of ores without any loss of the valuable metals, and at a very low cost. History of the Development of the Process The roasting process had its beginning in connection with research work at the Utah State School of Mines. N. C. Christensen, Jr., who held one of the School of Mines' fellowships, was engaged in some experimental work on blast roasting. At the same time I was doing some work on the insoluble gold in Mercur base ores. Mr. Christensen roasted some of this base gold ore in his pot furnace, and found that when he mixed a sufficiently low percentage of fuel with the ore, it did not sinter but roasted to a leachable product. We considered this a new application of blast roasting, and proceeded to test out a large number of ores in several different types of small roasters which we constructed. This experimental work continued well into the summer of 1911.

Jan 7, 1914

Single orders 2.5 c. Pamphlets 10. c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlet, of the same or different titles. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long as the supply, lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets that have been published by the Institute. Any other paper published by the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare.

Jan 5, 1917

By Jun-Yan Chen

Ground control problems in sublevel caving become evident as the rock pressure increases with depth. Recently, a finite element analysis of the stability problem of the sublevel caving method was completed by the author. This paper summarizes the results of stress analysis in sublevel extraction drifts under different field stress conditions by using linear elastic and nonlinear elastic-plastic finite element modeling techniques. A critical stress concentration will occur in the uppermost sublevel drifts beneath the caved area or blasted ore area. During the blasting and drawing cycle, a tensile and shear failure condition could develop in the center extraction drift when it would be mined last. Under a high horizontal stress field condition, almost all tensile stress in the back of the extraction drifts will be eliminated and only slight yield can be seen in the floor of the extraction drifts. Compared to the cases under the stress field where vertical stress is the dominant factor, the total yielding zone will be greatly reduced because of an in- creasing horizontal stress field with depth. However, it is predicted that the center of each ore column side will experience excessive shear stress that probably will result in ore failure. The two major conclusions drawn from this study to improve the overall stability of sublevel caving are: (1) the drift width must be carefully controlled and an appropriate stoping sequence selected; and (2) the sublevel caving method can be used in deep min

Jan 1, 1983

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By M. L. Jeremic

The massive Pb-Zn-Ag sulfide ore body is originated at the contact between the porphyry (footwall) and volcanic (hanging wall). The ore zone is folded and refolded, which results in two different structural geometries of the individual ore bodies. This requires both shrinkage and cut-and-fill mining methods. Strong bedrock resists caving after shrinkage stope completion, so high stress zones are developed below and above the mined area. The cut-and fill system has a limited destressing mechanism, where the stope walls with a backfill exhibiting stress close to a primitive one. This results in closure deformation of the open stope walls, yielding deformations of crown pillars and roof falls of the wide stope backs.

Jan 1, 1985

By Clifford Wilson

SCREENED pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments a. Consolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use. of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1932

By C. H. Mathewson, P. W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By Seymour G. Epstein

Using a modified capillary-reservoir technique, electromigration of dilute solutions of silver in liquid bismuth has been measured with relatively good precision. The effects of experiment duration, temperature. current density, and silver concentration have been investigated. Chemical diffusion coefficients of silver in liquid bismuth were also measured at temperatures ranging from 300°to 600°C. The effective valence of silver in bismuth was calculated as a function of temperature from a comparison of electric mobilities and diffusion coefficients. In an alloy containing 1 wt pct Ag, the electric mobility of silver increased from 1.65 x X sq cm per v-sec at 300°C to 2.38 x 10-4at 600°C; the diffusion coefficient in-creased from 3.0 to 17.5 x 10-5 sq cm per sec over the same temperature range. Calculated values of effective valence decreased from 0.28 at 300°C to 0.10 at 600°c. ALTHOUGH there has been considerable progress in the theoretical treatment of electron-transport properties in liquid metals, the mechanisms of mass-transport phenomena in liquid metals are still not clearly understood. This is especially true for the case of electro migration, alternatively termed elec-trotransport or electrodiffusion, which is mass transport induced by an applied electric field. A thorough knowledge of the mechanisms governing electromigration will considerably aid in understanding the electronic state of an impurity atom in a liquid metal. Electromigration has been long observed and studied in liquid metals and alloys. However, no satisfactory theory to explain the observed effects has been developed. The disparity in the present theoretical treatments, summarized by Verhoeven,1 has been attributed to the difficulty in describing the momentum transfer between electrons and ions and to the lack of precise measurements in liquid metals, especially at elevated temperatures. Prior to the last decade most of the electromigration studies were qualitative, in that only the direction of migration of alloy constituents was determined with any degree of reliability. These results have been summarized by schwarz,2 who was able to measure the electric mobility of several elements in mercury. More recently electromigration in liquid metals has been measured by a variety of techniques, with a varying degree of success. Mangelsdorf3,4 made precise measurements on dilute amalgams at room temperature, using a technique relating changes in composition to changes in alloy resistivity, but was unable to make measurements at elevated temperatures. Using a modification of this technique, Verhoeven and Hucke5 measured electromigration and resistivities in liquid Bi-Sn alloys. However, the resistivity technique is not sensitive to small composition changes and is impractical for very dilute alloys. Verhoeven and Hucke6 also measured electromigration of several solutes in liquid bismuth by adapting the capillary-reservoir method for determining diffusion coefficients in liquids. The reported precision of these measurements was poor, however, primarily due to the large uncertainties in the chemical analyses to determine concentration changes. Belashchenko7 has summarized the recent Russian investigations of electromigration, many of which, however, are of questionable accuracy. The present study was initiated to develop an experimental technique which would be both versatile and sufficiently sensitive to yield precise measurements of electromigration of solutes in dilute metal alloys at elevated temperatures. Using this technique, a comprehensive study of silver in liquid bismuth was made to determine the effects of experimental variables on the apparent electric mobilities. Chemical diffusion coefficients of silver in liquid bismuth were also measured over the same temperature range for comparison with the electromigration data. EXPERIMENTAL TECHNIQUE Electromigration Measurements. Electromigration of silver in liquid bismuth was measured by the capillary-reservoir technique, similar to that used by Verhoeven and Hucke,6 but modified to yield more

Jan 1, 1967

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By L. E. Young

THE purpose of this paper is to start a discussion on: (1) methods of supporting the immediate roof, particularly of local areas of poor roof, during the mechanical loading of coal; (2) methods of increasing the rapidity of the movement of the mining faces so that, without the use of cribs, jacks, pack walls, and filling, there will be no danger to men, equipment,, and working places from the subsidence of the overlying strata. In the Pittsburgh district the application of mechanical loading devices in mines working in the Pittsburgh seam, has been retarded by the difficulties of holding and handling the draw slate. Normally the thickness of this slate averages about 8 in. but the hardness varies, and a cut of coal cannot always be loaded without placing posts or crossbars to support the slate. Locally, the slate may be thicker and special methods of support may be required. If crossbars are placed to hold the slate when the coal averages 5 ft. in thickness, the standard methods of transporting the coal cannot be followed, and the use of conveyors may be desirable. Very little information is available on the effect of increasing the rate of movement of advancing or retreating break lines or longwall faces. A few British publications have presented some data but all such data relate to longwall faces that have moved not more than 6 ft. a day. The most rapid rate of movement of longwall faces in Germany is 6 ft. per day. In the ordinary hand-loading mine in western Pennsylvania break lines on full retreat will move about 2 ft. per day. If loading machines are used under similar conditions the, rate of retreat may reach 4 ft. per day. In a mine where coal is loaded by hand on conveyors three shifts per day, the rate of retreat has ranged from 11 to 16 ft. per day, with an average of 13 ft. If mobile loading machines could be used to load on con-veyors on break lines, the rate of retreat should be increased substantially.

Jan 1, 1938

By D. I. Cameron

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at 1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystal- line thoria.

Jan 1, 1962