Search Documents

By L. P. Teas

In spite of the influx of operators into the Gulf Coast anxious to retrieve their depleted production in other fields, and in spite of very active application of the most scientific geophysical methods to locate new producing areas, the results have been very discouraging and the year has failed to produce more than the average results for a Gulf Coast year. During the year seven new oil fields, some of which are still of very little importance, and one new gas area have been discovered. These fields are Tom Ball, Greta, Cleveland, Raisin and Garwood in Colorado County; Louise and Premont in Jim Wells County, and the new producing gas area near Ace in southern Polk County. During the year salt has been found for the first time at Carlos and Esperson. New producing areas have been developed on East Stratton Ridge, Hockley, Hull, Port Neches, near Pettus in Bee County, and on the O'Connor Ranch in Victoria County. The total production for the Gulf Coast for the year was 62,837,435 bbl., an increase of 18,589,000 bbl. over 1932. During the year, 1307 wells have been drilled of which 207 were wildcats, compared with 653 wells and 141 wildcats the previous year. The total daily production at the end of the year was 165,201 bbl. At present there are 3100 oil wells producing. The average production per well is 55.5 bbl. per day. The price of crude fluctuated considerably during the year, beginning at 80c per barrel and closing the year at $1.04 per barrel. Completion data for 1933 are as follows:

Jan 1, 1934

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

By W. A. Wood, W. H. Reimann, K. R. Sargant

A study is made of the microstructural changes produced in armco and pure iron subjected to alternating torsion at amplitudes above and below the knee of the S/N curve. The aim was to identify the basic mechanisms of fatigue and to find why they should give rise to a sharp S/N knee in contrast to the type of S/N curve shown by fcc metals. It is found that the basic structural change above the knee in the iron is a pronounced cell formation in the grains, which determines irregular micro-cracks, and below the knee a dispersion of fine slip that determines a dispersed pore formation in the grains. Comparison of these changes with those in fcc metals similarly tested shows that they do not include an intermediate structural change, a concentrating of slip in narrow bands with associated slip-band cracking, that characterizes the fcc metals and accounts for their different type of S/N curve. RECENT conferences on basic mechanisms of fatigue emphasize that fatigue damage takes many forms: for example, cracking in slip bands (Thompson1), at grain boundaries and inclusions (Hempel'), at precipitation zones in alloys (Han-stock, Forsythe), or at surface notch-peak effects, both hypothetical (Mott, cottrel16) and observed (Wood). Evidently it is not easy to see in this diversity a basic mechanism. At the same time the contributions suggest that some reconciliation may be possible if distinctions are drawn between three phases of the fatigue process: initiation of damage at nuclei, distribution of these nuclei, and the final macroscopic crack system. In initiation, the relevant features appear to be that nuclei may appear early, at least by 1/100th to 1/1000th of the life of a test specimen; that they may do so at many independent centers, appearing according to some observationsa as pores or voids; and that they are not necessarily self-propagating, damage spreading rather by their multiplication. In distribution, the relevant feature appears to be that they form preferentially in zones where the microstructure becomes abnormally strained (as defined more closely below). Now in these two phases the basic fatigue process should be systematic. But, at the same time, the "abnormal strains" in particular set the stage for considerable diversity in the final phase of macroscopic cracking, for where zones of abnormal strain develop will depend on what kind of fatigue deformation is applied and what kind of prior processing the test material has had. On this view it seems desirable to know what in

Jan 1, 1964

THE ladle is a small hearth made on a cage of iron bars like a bird-cage, and has a handle so that it can easily be taken from the forge and carried wherever desired. It is a common device and is much used among masters for small castings, but with a large weight you would have difficulty in lifting it by hand even though you were aided by levers and winches. If you should indeed do it, it would be just as if you had lifted the aforesaid hearth by force, and this would be unwise if you could do anything less difficult. A forge is likewise made for this, with a good pair of large bellows that are well covered with cloth. When the small hearth has been made with good clay, baked, and well covered with ashes, it is placed in front of the mouth [of the bellows] and a crown of two or three brick ends is built around it on top of the rim so that the charcoal may be held better and in greater quantity. Then, having lit the fire and heated the ladle and the charcoal, the pieces of material that you wish to melt are gradually put on

Jan 1, 1942

By Lawrence B. Wright

THE Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 following installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticline and a cross anticline recumbent against Cretaceous granodiorite, and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to oremaking materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937. The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about 1 to 4 and in the disseminated and breccia ores, 1 to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene.

Jan 1, 1947

EVERY dry thing that burns easily and multiplies or maintains fire by its own intrinsic nature can be put into an incendiary composition and various effects are produced. Some of these things are mineral combinations, like sulphur or its oil; some others, [163v] hot, dry, and subtle substances, like saltpeter; and some are. unctuous things, like fats and oils of any kind; while some serve because of dryness, like pith and wood. Some of these things are natural and some artificial But now I set aside the search for these differences in their composition. This is what I have found among all the ancient and modern things that I have been able to seek, and first, back in the time of Alexander the Great. Marcus Graecus, who was perhaps the inventor or a great experimenter and practicer of such things, writes of many of them. I have chosen some among these, and one* is this: In order to make it, he took Grecian pitch, alchitran, live sulphur, tartar, sarcocolla, niter, and petroleum oil, one part of each, and, in addition, a double amount of quicklime. He mixed it all with oil of egg yolks. Having put it in a well-covered and closed vessel of glass or glazed earthenware under warm manure, he left it for a month. Then, having liquefied it over a slow fire, always keeping the vessel well closed, he finally put this liquor in hollow sticks, in little pots, or in vessels expressly made, all with a little fuse fitted in the middle. If I should have to do this, I would say that a little gunpowder should be put in, which should give beginning to the fire so that it would ignite more easily. I have also found that another fire is made. For this sulphur is taken, or oil of sulphur if it is possible to obtain, petroleum oil or some rock oil, juniper oil, very well-refined saltpeter, and for one part of each of these five parts of asphalt; in addition, take goose or duck fat, pure black pitch, varnish, pulverized dove's dung, and enough aqua vitae to cover all the aforesaid things.. Then it is put in a glass vessel under warm manure for

Jan 1, 1942

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

The study of copper alloys of the age-hardening type has received considerable attention, and, among the alloys which the authors have, considered, those containing small amounts of nickel and phosphorus as essential constituents seem especially interesting. Such alloys have attractively great capacity for being hardened and also have relatively high electrical and thermal conductivity in the hardened state. In addition, it has been found that the increase in hardness and strength imparted by aging can be greatly augmented by cold-working, so that excellent combinations of conductivity and strength are obtainnble. In view of the possible importance of the alloys, it was considered desirable to investigate the solubility relationships in the copper-rich portion of the copper-nickel-phosphorus system. This paper present's some of the results obtained in this investigation to date and also gives propertics of typical alloys that appear to be of commercial interest,. Review of literature Copper-nickel System,.—The binary coppcr-nickcl system has long been known to consist of a series of simple solicl solutions, copper and nickel being miscible at all tempcrat'ures and concentrations. This was establisl~cd by Guertler arid Tammannl in 1907 and confirmed by Tafel2 in 1908. Copper-phosphorus System.—The copper phosporus system has been studied by numerous investigators, so that the copper-rich portion is now definitely known. As most recently determined by Lindlief," his system has a cutectic at 8.38 per ccnt P, cuteetic temperature being 714° C. Components of the cutectic are Cu3P and alpha solid solution. Solid solubility of phosphorus in copper, according to Mertz arid Mathewson decreases from a maximum of about 1.75 per cent at 714' C. to about 0.6 per cent at 300' C.

Jan 1, 1940

By G. W. Thomas

Jan 1, 1967

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

By E. F. Young

The Porter Tunnel will open up 10 million tons of coal for Philadelphia & Reading which can be taken without hoists or pumps.

Jan 3, 1951

By H. E. Mussey

When the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then completed were referred to as monumental.' Their dimensions are givcn in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 1, 1925

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970

CHARLES E. GUILLAUME,* .Sèvres, France written discussion?).-Referring top. 2052, experiments made at the end of the year 1884showed a remarkable agreement between the indications of various verre dur thermometers of which all the corrections had been determined with the greatest possible precision. The maximum deviations not attributable to the comparisons themselves were then about 0.002 to 0.003 degree. Much later, greater differences began to show. They were caused by the fact that the glassmaker-had modified the composition by adding to it a small quantity of lead. Efforts are now being made in France to obtain a regular, supply of glass made according to the old formula. The determination of the boiling point of sulfur made by Chappuis,1 444.5°, accords very well with the value noted on p. 2054. The International Committee of Weights and Measures and the General Conference have already considered the future abandonment of the hydrogen scale in favor of the thermodynamic scale. The hydro-gen scale appears to be, in their estimation, a transitory one, happily so closely approaching the final scale that no correction should be necessary for all measurements of temperature made during the last 30 years.

Jan 12, 1919

By Edgar Trask

EACH branch of engineering seems to depend on the cooperation and contribution of some other branches to enable it to produce more efficient methods and appliances for man to use. The purpose of this paper is to show approximately the gain in efficiency of self-propelled merchant ships when steel of greater elasticity is substituted for mild steel in some of the strength members and alu-minum alloy is substituted in some of the parts where strength is not essential. The new steel will have some greater strength and a much greater elastic limit in the as-rolled condition, and must be readily weld-able under ordinary conditions of shipbuilding. Naturally, its cost may be more than mild steel, but if the demand is great that excess cost may be reduced to an amount that will make its use more economical than that of the present mild steel. There appears to be a well defined axiom in engineering today that to use the least power to carry a given load the weight of the carrier must be reduced to a minimum. This minimum must be, of course, consistent with the necessary strength, rigidity and durability and it must not be attained at an excessive cost where the fixed charges of the carrier will exceed the savings in, operating the motive power. Recent railroad equipment is a notable example of this, and in these trains alloy steels and aluminum together with less weight per horsepower of the power plant are reducing the weight of the carrier and hence the total power required for moving the paying load. Before considering the application of these metals to shipbuilding, it is well to explain some of the fundamentals of ship design.

Jan 1, 1936

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, 'and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.' The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By I. H. Silberberg, R. L. Reed, O. K. Kimbler

interfacial films have frequently been observed at interfaces between certain crude oils and water. Several investigators have postulated that the presence of these films should influence the efficiency of oil recovery in water drive or waterflood operations. They may also influence the stability of emulsions which are sometimes a problem in petroleum production, and may be a factor in the fonation of paraffin deposits in oil well tubing and flow lines. This paper presents a technique with which a modified Langmuir film balance may be used to study the compressibility and collapse pressure of these natural interfacial films. Experimental data are presented for several nude oil-water systems. Data developed are used to infer the phase state of the film as a function of such variables as rate of reduction of interfacial area, ionic composition of the subtrate and pH of the subtrate. A film of known physical characteristics is shown to have a sinnificant effect on oil recovery from an unconsolidated sand pack. Possible applications of these results to petroleum production are discussed. INTRODUCTION The use of water to displace petroleum from reservoir rocks is of major importance both as a primary and a secondary recovery process. As water invades the rock, oil is completely displaced from some pores and left as a discontinuous phase in other pores. The manner in which water moves from pore to pore is strongly influenced by capillary forces. In view of the complexity of reservoir fluid systems, there can be little doubt that complicated interactions take place at both the liquid-solid and oil-water interfaces. One of the more interesting, and least understood, of the phenomena which take place at the oil-water interface is the formation of interfacial films. These films are believed to result from the adsorption of high molecular weight polar molecules at the interface.l.2 Presence of such molecules may cause a striking alteration in interfacial tension. When the oil-water interfacial area of certain crudes is rapidly reduced, a thin region (film) about the interface assumes the appearance of a solid membrane, and striations, wrinkles and gross distortions may occur. If such a film is solid, it should greatly alter the interfacial tension normally assumed to exist between the oil and water phases. If the membrane is continuous, a solid phase would separate the oil and water. Interfacial films between crude oil and water were observed in 1949 by Bartell and Niederhausers who commented upon the apparent rigidity of the films and their possible importance in the petroleum industry. Morrell and Egloff4 had earlier attributed the extreme stability of emulsions of sea water in fuel oil to very stable asphaltic films. Numerous investigators have observed rigid films in the course of crude oil-water interfacial tension determinations by the pendent drop method. Several investigators5,6,2 have separated inter-facially active materials from crudes and attempted to characterize them chemically. Reisberg and Doscher,2 using Ventura crude, showed the interfacial tension against water (as measured by the pendent drop method) to be affected by aging, contraction and expansion of the interface, and the pH of the water. These investigators attributed the adhesion of oil to a water-wetted surface and the distortions of flow paths in glass capillaries to the presence of rigid films. Dodd7 has studied the interfacial viscosity of adsorbed films and found them to be non-Newtonian in behavior. Craighead and Harvey8 reported a series of displacements in tubes packed with 60 mesh glass beads. They interpreted the results as indicating an effect of stearic acid films on waterflood recovery and imply that natural films may produce similar results.

Jan 1, 1967

By A. T. Peters

DURING an investigation concerning the use of large nozzles for pouring of low-carbon rimming steels, the practical details of which were reported elsewhere, it was noticed that increases of nozzle sizes were generally followed by improvements of slab surface quality. It is the purpose of this note to present the data available and some tentative opinions about this phenomenon. The problem of correlating pouring rates with the metallurgical performance of steels is complicated by several factors. The two most important are; 1) Variations of the steel pouring rate throughout a pour, these being due to the nozzle erosion, which enlarges the bore area, and the dropping ferrostatic pressure in the ladle. The pouring rate is lowest towards the end of a heat when the ladle is nearly empty. 2) Variations in the ingot pouring time due to the different ingot weights poured. Consequently, the use of the average pouring rate of a heat may not be exact, but in large-scale production it is not practical to treat ingots separately according to their pouring rates. The variations of ingot weights and sizes may be overcome by considering the rate of rise of steel in the mold. Hence, the average rate of filling of molds throughout the pour of a heat, inches per second, will be used in this note. Every ingot rolled at Inland is rated at the blooming mills prior to hot machine scarfing as being good, fair, or poor for cracks, scabs, and checking. The latter term refers to the network of breaks or lines associated with overheating or burning in the soaking pits. It is also known that thin-skinned steel is prone to show this defect if the subsurface blowholes are exposed during reheating or rolling. The experiences with the surface quality of slabs rolled from ingots poured at different rates are presented in Fig. 1. The data represent nearly 11,000 ingots. It appears that all three types of defects are in-

Jan 1, 1960

By P. H. Dudley

I HAVE taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its economical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 95i miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 foot-pounds, exclusive of the force to move the locomotive itself. We

Jan 1, 1876

Reno, Nevada. J A Fulton, Director For publications of either the Mackay School of Mines or the State Bureau of Mines, address the School of Mines at the given address. Except where the contrary is indicated in the following list, available publications are sent free From the Mackay School of Mines. Bulletin 1, The identification of Nevada's common minerals, 50 cents; 3, Notes on the ore deposits of Cave Valley mining district, Lincoln County, 4, A preliminary survey of the Scossa mining district, Pershing County, 5, Ore deposits of the Gold Circle mining district, Elko County, 6, Bedded deposits of manganese oxides near Las Vegas, 7, Spruce Mountain district, Elko County, and Cherry Creek (Egan Canyon) district, White Pine County From the State Bureau of Mines: Bulletin 1, Mineral resources of southern Nevada One volume: Mining districts and mineral resources of Nevada, by F C. Lincoln (1923), $1.50.

Jan 1, 1933