Search Documents

By A. M. Gaudin

TEN years ago Taggart, Taylor and Ince1 described a workable, convenient apparatus for the measurement of contact angles be-tween cleaved, ground or polished particles and captive bubbles. Wark and Cox2 and Wark and Sutherland3 have done an im-mense amount of experimental work with this apparatus. Their work has had as principal object the determination of "con-tact curves." Contact curves are Cartesian charts in which pH (or some other variable) is plot-ted against quantity of modifying agent. The rectangular area is broken into two or more curvilinear areas separated by the contact curve. The curve indicates that a sharp demarcation exists between condi-tions that bring about sticking of particles to bubbles and conditions that do not pro-duce sticking, The type curve appears in the TRANSACTIONS as Fig. 1, page 248, volume 112. Wark and Cox offer data to show that the contact angle has a value determined by and characteristic of the agent used. Wark and Cox also make the statement that they believe this value is independent of concen-tration (ref. 2a, p. 209), They say: It is suspected that, given sufficient time and provided that there are no disturbing factors. the full ethyl xanthate angle (corresponding to a complete xanthate film) would be obtained in every case where contact occurs.

Jan 1, 1940

By C. D. Jardine, D. G. Patton

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. An application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by using a "building block" approach to design and equipment selection.

Jan 1, 1985

The conservation movement, initiated during the time of Gifford Pinchot and Theodore Roosevelt, has gradually taken hold of the popular imagination of the American people; and today, although it is little understood, it is an accepted doctrine. But the subject should not degenerate into cheap and misleading publicity. In the wise development and use of human and material resources lies the answer (Fig. 4). Conservation does not mean the parsimonious and misguided avarice of the miser, but the prudent and intelligent use of all types of resources, and the opening of a way for the use of those potentialities that lie just beyond the horizon and wait for man's constructive efforts to make them available. Conservation consists essentially in not emptying the pools of primary wealth before the minds of men, guided by ingenious research, have found ways to replenish them from sources as yet untapped. To advance successfully along this path, man should be guided by science and by a decent understanding of his obligations to his fellow man and particularly to his children and his children's children. Two pathways branch from this general road. One is the restraining of those spendthrifts who would throw away our national heritage for the sake of a cheap and irresponsible enjoyment of the present. Conservation in the generally understood sense usually has meant

Jan 1, 1950

By P. A. Young

The historical background of on-strand cooling is given, together with a resume of recent practical developments. Laboratory test procedures are then considered in detail, for both productivity and quality parameters, with particular reference to the design of the Ravenscraig No 3 machine (Scotland). A heat transfer model is presented for a porous sinter with propagating cracks. The influence of cooling/sintering area ratio, sinter strength, granulometry, return fines, coke consumption and FeO levels are examined in relation to economics. A detailed comparison of capital and running costs for two different strands, designed for identical duties, but with off or on-strand cooling, is then given.

Jan 1, 1977

By H. J. Seaman

The cost of keeping platinum ware in repair becomes such an important item in laboratories where much fusion-work is done, that a method of saving in this direction may not prove unacceptable to at least some of the members of the Institute. Some two years since I had the misfortune to puncture an almost new Bishop crucible. As an experiment I endeavored to patch it, and with such success that it is still in constant use. This may be accomplished in the following manner : The crucible and patch, which should be of stout foil, are rubbed bright with silica, or rotten-stone; a light platinum wire, welded to a corner of the patch, and the whole treated for several hours with hot concentrated hydrochloric acid; after which they are thoroughly washed with distilled water and dried. The head of an ordinary iron rivet, 4 inches by $ inches, is rounded off by hammering to somewhat the shape of the crucible. This is sunk 2 inches in a block of hard wood, and firmly wedged in place. This serves for an anvil. The hammer is an ordinary cast-iron toy, 11/2 inches long, and # inches in face, mounted on a 4 inch iron rod, 10 inches long. A gas-blowpipe is fixed in a horizontal position, and the strongest heat obtainable with it directed upon the rivet head; this soon at-

Jan 1, 1885

By Edgar S. Burkhardt

In mining, the process of comminution starts at the pit and ends at the classifiers. The first machine that breaks or comminutes ore is the primary crusher. There are many types of crushers, but the one most commonly used in large tonnage plants is the gyratory so discussion is restricted to this type of machine. See Figure 1. The primary crusher is the most important piece of comminution machinery in the plant because every ton of ore processed by the concentrator must pass through it, as shown in Figure 2. Most plants can operate if a secondary crusher or a mill is shut down, but if the primary crusher stops, the whole concentrator goes down. It is, therefore, important that the machine be able to produce sufficient ore to keep the concentrator running without hesitation. The plant designer first considers the required daily capacity and an estimate of the size of the ore from the pit. To this he adds an availability factor to compensate for delays due to shovels, trucks and rou- [ ] tine maintenance at the crushing station. This factor is based on experience and can be on the order of 75% (1). With these figures, he determines the hourly capacity required of the primary crushing station to keep the concentrator supplied. See Table I.

Jan 1, 1982

By Dorsey Hager

The possibility of oil and gas production in Alabama his been little considered as yet. Gas and some oil have been found in northwestern Alabama, near Birmingham, in the Pennsylvanian beds, but the oil and gas possibilities in the Cretaceous beds are not generally appreciated. The recent activity of oil companies in that State has attracted much attention, and in this paper the main structural and the general strati-graphic features are described. Four favorable areas are outlined. These contain folds of major interest. There are other favorable areas which have not been mapped-l Commercial pools discovered in this area would have the advantage of being near tidewater. Mobile, Ala., on the Gulf of Mexico, would be the logical site for refineries and shipping facilities. A pipe line could readily be laid to that city from the Hatchitigbee and the Jackson areas. The logical outlet for the Geneva and the Gordon areas would be Panama City, Ha., on the Gulf of Mexico. Topography The whole of the area under consideration lies in the Gulf coastal plain and slopes gently to the southwest and west. The elevations vary from 200 to 400 ft. (60 to 121 m.) above sea level. The streams have sunk their channels into this gently sloping plain, the main drainage flowing south or southwest into the Gulf of Mexico. Between the

Jan 1, 1918

By Carl Floe

THE possibility of separating the various constituents of mixed ores or metalliferous products by differentially producing their soluble sulfates has not received the consideration that it deserves. The production of the soluble sulfate may be accomplished by baking the ore with sulfuric acid or by treating it with gases containing oxides of sulfur. This paper is primarily concerned with the first method. The procedure used was to mix the material with a solution containing a definite weight of sulfuric acid, baking the mixture at various tempera-tures and then leaching out the soluble sulfate with water. The amount of acid used was calculated to produce certain desired soluble sulfates. The temperature of baking depended on the decomposition points of the sulfates involved. The object was to prevent the formation of or to decompose certain sulfates while leaving a maximum quantity of another sulfate in a water-soluble form. This procedure has two possible advantages over the ordinary method of leaching with an aqueous solution of sulfuric acid. First, a more selective leach may be obtained, and second, the higher temperatures and stronger acid concentrations involved will permit a better recovery of materials that are difficultly soluble in relatively dilute aqueous sulfuric acid solutions. The method of sulfuric acid baking followed by water leaching is not new, as it has been applied in the treatment of various metalliferous materials such as the recovery of cadmium from flue dust1, the re-treat-ment of zinc leach residues2 and the working up of electrolytic slimes3.

Jan 1, 1936

By W. B. Mather

A SURVEY of the technical literature concerned with oil well drilling methods and particularly with rate of penetration by various cutting media on different types of rock provides a mass of conflicting data. This is especially true with respect to, (1) the relative efficiency of diamond, rotary and percussion drilling operations; (2) the costs of the various types of drilling; and (3) the hardness factor of various types of rock and cutting media. The latter is the particular phase of the subject discussed here. The cause of the confusion may be attributed partially to a lack of 'basic knowledge concerning the physical properties of the cutting media and of individual types of rock. It is also due in part to a general lack of uniform standards in the industry for evaluating the hardness versus drillability of rocks while possible errors in interpretation by the authors of the various papers pertaining to the subject may be an additional cause of misunderstanding. The hardness of a mineral is defined by Dana' as "the resistance which a smooth surface offers to abrasion." Webster' states that hardness is "the cohesion of the particles on the surface of a body (as a mineral) as determined by its capacity to scratch another or be itself scratched." Rock hardness, although not usually defined in publications describing rocks, is assumed to be the same as the minerals which compose the rock or the resistance of the rock to abrasion. Drillability of a rock may be defined arbitrarily as the rate at which rock is penetrated by a definite type of drilling tool with the assistance of a specific type of cutting surface or medium and under speci- fied conditions as to speed of rotation and applications of pressure. Eventually the term penetrability may have to be employed to include any method of making boreholes in rocks, since methods other than those using conventional cutting surfaces are already in operation. A case in point is the jet piercing methoda which employs an oxy-acetylene flame as a means of penetration. The word hardness as used by the drilling fraternity has a variety of meanings which depend upon the type of drilling method employed. For example, in diamond drilling, hardness is interpretated as resistance to abrasion. In percussion drilling the term implies resistance to impact or indentation, while in rotary drilling, hardness is considered anal-agous to compressive strength. The three types of hardness—abrasion, impact and compression—are conflicting variables for different types of rock. Nevertheless, the term hardness is applied indiscriminately by the industry for the resistance of rock to penetration by any type of drilling technique. Abrasion Hardness Since 1818, Moh's scale of hardness, although only relative in nature, has been accepted universally as the method of measuring mineral and therefore rock hardness. In 1933, Ridgway, Ballard and

Jan 1, 1952

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic loca- tion or seam characteristics, modern raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality, and these objectives may be sought by commencing the preparation of coal underground at the "working face." Under- ground preparation involves choosing those portions of the seam which can be cleaned to satisfy predetermined market requirements involving ( 1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios, and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1 ) seam under development, (2) mining equipment available, and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another, the (1) petrography of the coal in the seam does not remain uniform, (2) character of roof and floor are subject to change, and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution, and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content, and petrography are of considerable interest, and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking, and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal.

Jan 1, 1979

By P. G. Carpenter, H. B. Fisher, W. E. Bergman

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By N. S. Stoloff, R. G. Davis

It is concluded from an X-ray stztdy that the formation of the hcp Mg3Cd superlattice is a nuclea-tion and growth reaction. A two-phase, ordered-plus-disordered, region is observed between 153" nnd 141"C. A maximum in the flow stress is observed both at temperature and in quenched specimens within the two-phase region. The peak arises fro112 the extra energy required to create antiphase boundary upon cutting the ordered regions. Hardening during isothermal annealing in Mg3Cd has been shown to be similar to the domain hardening in Cu3Au-type alloys in that up to the maximum the structure is ordered domains growing into a short range ordered matrix. The hardening is due to a combination of short range order strengthening and the strengthening produced when antiphase boundary has to be created. In a recent study1 of the effect of long-range order upon the mechanical properties and deformation modes of hcp Mg3Cd a comparison was made be- tween quenched (disordered) and slow-cooled (fully ordered) specimens. The most striking observations were that the disordered alloy yields at a much higher stress than the ordered alloy, and that there is a change in slip mode from primarily (_0001) ba_sal slip in the disordered state to (0001), {1010}, {1122}, and {l011} slip in the ordered state. The main purpose of the present work is to extend these observations to determine whether MgsCd exhibits a peak in flow stress at an intermediate degree of order, or at a critical domain size, as do other orderedstems. However, disagreement exists about the Mg3Cd order transformation with respect to: 1) the location of the critical temperature for order, 165°C or 153"~,' and 2) how the degree of order varies with temperature. Welber et a1.5 concluded from specific heat measurements that the formation of Mg3Cd is a second-order reaction with the degree of order a continuous function of temperature, while Moore and Raynor concluded that it is neither a first-order reaction, with the degree of order a discontinuous function of temperature, nor a second-order reaction. Consequently it was considered necessary to undertake an X-ray investigation into the change in degree of order and structure in the

Jan 1, 1964

By W. R. Ingalls

MANY years ago, I expressed the opinion, in writings and otherwise, that it was possible to desulfurize zinc blende autogenously, i.e., without the use of extraneous fuel, and that at some time this would be accomplished. This opinion was based on thermal calculations and also on observations of the behavior of blende during roasting in different ways, all of which observations tended to confirm the theoretical calculations. Among such observations were things like the following: Once in carrying out the stall roast of cupriferous pyrites as a regular metal-lurgical operation, I was minded to charge a stall with lump blende, ranging from walnut to egg size, as I recollect, following the same procedure as with pyrites, and setting fire to the kindling wood, observe what would happen. The blende charge ignited well enough and bravely began to burn, quite actively the first day, at a diminished rate the second day, while on the third day burning ceased and the charge quickly became cold. It was just like trying to set a grate full of anthracite afire with insufficient kindling wood. The volume of air drawn through the stall was too great, quickly cooling the entire contents below the ignition temperature, which means, of course, that burning ceased.

Jan 12, 1922

By Rossiter W. Raymond

THE most important event in the history of mining in the United States was the discovery of gold in California, which led to the rapid development, not only of a new industry, but of a new empire. The settlement of the Pacific slope was making but slow progress under the inducements of a scanty commerce in furs and hides. The liberal grants offered by the government to agricultural pioneers in Oregon had attracted to the Willamette valley and other favored points in that territory a limited population; but the government of the Mexicans in California was positively unfavorable to enterprise. It is true that gold was known to exist in the country. Rumors of it were current among the trappers, and placers had actually been worked in what is now Los Angeles County ; but the padres of the neighboring mission of San Fernando had discouraged the business as demoralizing to their flocks ; and the existence of the precious metal was not widely known; still less was its distribution north¬ward suspected. The discovery of gold, January 19th, 1848, at Sutter's saw-mill, on the south fork of the American River, afterward famous as Coloma, in Eldorado County, was the beginning of the new epoch. This discovery was made by James Wilson Marshall, a partner in the mill, who observed in the debris washed down by the tail-race a glittering fragment of a mineral unknown to him. Suspecting it to be gold, he sought for further specimens, and obtained, in the course of a few days, several ounces of it. Tests subsequently

Jan 1, 1875

By S. R. B. Cooke, Y. S. Kim, I. Iwasaki

lron oxides or the gangue minerals of iron ores can be made to float, depending upon the choice of collector. The selectivity of the separation is controlled by the accompanying chemical and operating conditions. In this report the findings on the general flotation characteristics of magnetite are summarized and the results are compared with those obtained for other iron oxides. Depending upon the choice of collector, either the iron oxides or the gangue minerals of iron ores can be made to float, the selectivity of the separation being controlled by the accompanying chemical and operating conditions. The mechanism by which a collector exerts preferential affinity for either group of minerals has been a subject of extended discussion. Previous investigations on the electrokinetic properties and flotation characteristics of hematite,' goethite,2 and quartz3 have demonstrated the electrical nature of the interaction of the collector with these oxide surfaces; anionic collectors are effective on positively charged surfaces and cationic collectors on negatively charged surfaces. Thus, from the differences in the electrokinetic properties of the above-named oxides, a theoretical basis has been provided for their separation by some typical collectors. Examination of the results reported for hematite and goethite shows that their electrokinetic properties and flotation characteristics are remarkably similar. It is of considerable interest, therefore, to examine similar information for magnetite, another common iron oxide, in order to consolidate the flotation characteristics of the three principal minerals of oxide iron ores. Such information is practically significant in the up-grading of both natural and artificial mag- netite produced from taconite, and in the treatment of partially oxidized magnetite ores. Information on maghemite and lepidocrocite, polymorphs of hematite, and goethite, respectively, is also of some theoretical interest in ascertaining the effects of crystal structure and of hydration in the iron oxide group. This article reports the findings on the general flotation characttxistics of magnetite, and compares the results with those obtained for other iron oxides. Experimentally, tlhe surface properties of magnetite were investigated by electrophoresis, and by measurement of the aclsorption of some typical flotation collectors. Its flotation behavior was tested by contact angle measurements and by simple flotation tests using a modified Hallimond tube. The basic information thus gathered was shown to be directly applicable to the interpretation of the results of batch flotation tests made on an artificial mixture of magnetite and quartz. EXPERIMENTAL MATERIALS Magnetite: Magnetite concentrate from Port Henry, N. Y., was further purified by fine crushing and magnetic separaiion, and was used throughout this investigation. For flotation tests the 150/200 mesh fraction was iso1ated and was cleaned by leaching briefly with warn 0.1 N HC1 followed by repeated washing with demineralized water. The final sample analyzed 71.71 pct Fe, 22.37 pct Fe" and 0.47 pct insoluble, and was stored in demineralized water. For e1ectrophoresis and adsorption measurements, the —400 mesh fraction of the magnetite concentrate was ground dry in a pebble mill. The surface area of the ground sample, as determined by the gas permeability method, was 70,000 sq cm per g. Since artificial magnetite has been reported to possess somewhat different physical properties than those of natural magnetite, it also was briefly examined. Preliminary flotation tests on a sample of artificial magnelite, prepared by reducing Brazilian hematite in a C0/CO2 mixture and analyzing 71.94 pct Fe and 23.78 pct Fe'', gave, however, nearly identical results with those using natural magnetite. It was concluded that artificial magnetite behaves similarly to natural magnetite. Samples which had been magnetically separated showed a tendency to cluster together due to residual

Jan 1, 1962

By J. J. Pelley

NOT being a scientist, an engineer or a metallurgist, I consider it a very great honor indeed to be asked to address the American Institute of Mining and Metallurgical Engineers. Your program indicates that any lack of intricate and technical knowledge on my part in the field of metals will be well taken care of by others. Therefore, I believe any remarks that I have to make might well be devoted to the practical side of metals in railroad service and to the general railroad situation as I view it today. The experiments now being conducted on the railroads with so-called streamlined, light-weight trains and cars would not have been possible had it not been for scientific and engineering research in the past that made these lighter weight metals available. The railroads now have approximately forty units of these new trains in operation. Experi-ence with them will no doubt be a guidepost for future construction in that direction. While the best known experiments are in the passenger service, they are being extended into the freight service. Within the past three years there was constructed for the Association of American Railroads a new standard box car of ordinary carbon steel, in which, by reason of superior design, weight was reduced by 3500 to 4500 lb. under that of existing cars of like capacity. The Association is now testing a box car that weighs approximately six or seven tons less than practically all of the box cars of like capacity in service today. If these tests are successful a very large field for the use of lighter weight metals will immediately be opened, provided the costs of such metals are not too high. The fact that various experiments are being carried on with other classes of equipment constructed with so-called light-weight and non-corrosive metals no doubt will have a considerable effect upon the rebuild-ing of old equipment. The question then will be: How much can we afford to spend on the rebuilding of an old car weighing six to seven tons more than a new car constructed with the latest available materials?

Jan 1, 1936

By L. Massé, Th. Koulomzine

Note on Haalck's Formula Quantitative interpretation of magnetic anomalies is admittedly a difficult process. Few authors have attempted a general approach to this problem. A number of publications can be found widely scattered through scientific periodicals, which present particular solutions obtained by the introduction of simplifying assumptions, such as the reduction to an equivalent magnet or pole, or the hypothesis of a very thin vein. The practical applications of these solutions are necessarily very restricted though they have given satisfactory results in isolated cases. Probably the most widely known equation of this type was given by Haalck.' His classic work contains curves calculated for typical conditions, and has now become a standard reference. However, a close scrutiny of Haalck's derivation reveals that, aside from the hypothesis of a thin vein, it rests on the

Jan 1, 1949

By John M. Crowl, L. E. Sawyer

5.3-1. General Public Resistance to Strip Mining. Surface (strip) mining is the oldest recorded method of extracting coal and other minerals from the earth. This method of mining completely alters the topography of the earth's surface, leaving an area of more or less parallel ridges or of peaked mounds of the materials which overlay the mineral seam. It destroys all original vegetation and provides materials for new type soil. During the early years the acreage mined by this method was small, land was plentiful, and with a growing young nation no thought was given to the restoration of the disturbed areas to some form of productive use. Early in the present century the development of steam shovels and drag-lines made it possible to remove thicker overburden to recover the products. With the deeper digging, the size of the disturbed areas increased. With this increase in the size of equipment and the improvement of blasting techniques, mining was expanded into more prominent locations and to areas of more valuable land. The more progressive operators became aware of the need to reclaim those areas for some productive use. Electric shovels with capacities of up to 200 cu yd and draglines with capacities of 145 cu yd, capable of uncovering products over 100 ft below the surface, are now in use. Combined with the increase in the size of equipment, the expansion of contour mining or rim stripping in the mountainous areas has focused public attention on the need for a sound reclamation program for all disturbed areas. APPEARANCE. After mining, the areas consist of varying percentages of rock, shale, slate, and soil material devoid of all plant and animal life. Unless a definite reclamation plan is carried out, many of the mined areas will remain bare for a period of years. The topography of the area is completely altered. What may have been level to rolling land in cultivation, in grass, or in timber is thrown up into a series of ridges or mounds.

Jan 1, 1968

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form' The final pressure to which a natural gas may 'be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.' The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

By Rossiter Raymond

(Butte Meeting, August, 1913.) ON Mar. 28, 1913, the Board of Directors of the American Institute of Mining Engineers unanimously adopted the following Minute: JOHN FRITZ, one of the most distinguished of American mechanical and metallurgical engineers, won that position by the force of innate genius, indomitable industry, unstained integrity and unfailing sympathy, and generosity towards his fellow-men. Self-educated in the hard school of practice, he appreciated nevertheless the advantages of technical instruction and discussion, and evinced this appreciation both by his membership and lively interest in this and other similar societies, and by his munificent gifts to engineering education at Lehigh University, and his long and faithful service us a Trustee of that institution. . As one of the foremost of those American engineers who, through their brilliant inventions and practical skill. developed here -the modern iron blast-furnace -and rolling-mill, and introduced and perfected the Bessemer process and other improvements in the manufacture of steel, Mr. Fritz contributed mightily to the chief departments of that industrial progress which characterized the Nineteenth Century. Proud of his great achievements, we cannot but rejoice over his long and fruitful life, crowned with a peaceful death ; but our praise and thanks are mingled with sorrow, as we recall the kindly face which we shall see no more on earth, and the loyal friendship and spontaneous good-will which led the love of his generation, and the reverence of the generation which followed, to regard him universally as " Uncle John Fritz." That. summary, though only an outline, is a good portrait ; and in the present sketch, we shall do no more than supply some details of the likeness, and some elements of the background.

Jan 6, 1913